Sunvic TL ONE Manuale utente
Installation Guide
TL ONE
TL ONE
Electronic Thermostat
TL ONE
Installation Guide 3
1 Introduction
TL ONE is an electronic thermostat provided with a
2-pole switch and a room sensor to measure and control the
surface-mounted.
The thermostat has a button for adjusting the temperature
setting with a scale from ( ) 5-35°C. Furthermore, it has
a LED indicator showing standby periods (green light) and
heating periods (red light).
More information on this product can also be found at:
sunvic.co.uk
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 . . . . . . . . . . . . 4
1.2 Safety Instructions . . . . . . . . . . . . . . . . 5
2 Mounting Instructions . . . . . . . . . . . . . . . . 6
3 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Disposal Instruction . . . . . . . . . . . . . . . . . . 12
TL ONE
Installation Guide4
1.1
Operation voltage 220-240 V~, 50 Hz
Standby power consump-
tion
Max 0.25 W
Relay:
Resistive load
Inductive load
Max 15 A / 3450 W @ 230 V
cos φ= 0.3 max 1 A
Sensing units NTC 15 kOhm at 25 °C
Sensing values:
0 °C
25 °C
50 °C
42 kOhm
15 kOhm
6 kOhm
Hysteresis ± 0.2 °C
Ambient temperature -10 to +30°C
Frost protection temper-
ature
5 °C -
Temperature range () 5-35°C with room
sensor
1 x 4 mm² or 2 x 2,5 mm²
Ball pressure temperature 75 °C
Pollution degree 2 (domestic use)
Type 1C
Storage temperature -20 to +65°C
TL ONE
Installation Guide 5
IP class 31
Protection class Class II -
Dimensions 85 x 85 x 36 mm
Weight 90 g
The product complies with the EN/IEC Standard“Automatic
electrical controls for household and similar use”:
• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)
1.2 Safety Instructions
before installation.
IMPORTANT: When the thermostat is used to control a
Please also note the following:
• The installation of the thermostat must be done by an
regulations.
TL ONE
Installation Guide6
• The thermostat must be connected to a power supply
via an all-pole disconnection switch.
• Always connect the thermostat to continuous power
supply.
• Do not expose the thermostat to moisture, water,
dust, and excessive heat.
2 Mounting Instructions
Place the thermostat at a suitable height
on the wall (typically 80-170cm.).
In wet rooms, place the thermostat according
to local regulation on IP classes.
Do not place the thermostat on the inner
side of an exterior wall.
TL ONE
Installation Guide 7
Always install the thermostat at least 50 cm.
from windows and doors.
Do not place the thermostat in a way that
it will be exposed to direct sunlight.
Follow the steps below to mount the thermostat:
1. Open the thermostat:
devireg™550
3
5
6
24
20
30
40
50
• Press the release tab in the bottom of the ther-
• Carefully detach the front cover.
• Carefully detach the frame.
TL ONE
Installation Guide8
2. Connect the thermostat according to the connection
diagram.
IP31
-10T30
D531
Mains
220-240V~
Max. Load
15 (1) A
N L
N
LOAD
L
LOAD
9еквонатсуоповтсдовокуР
The screen of the heating cable must be connected
to the earth conductor of the power supply cable by
using a separate connector.
Note:
3. Mount and reassemble the thermostat.
• Fasten the thermostat to a socket or an exterior
wall box by driving the screws through the holes
in each side of the thermostat.
• Install the frame and front cover in the reverse
order of disassembly.
4. Turn on the power supply.
TL ONE
Installation Guide 9
TL ONE
Installation Guide
4 Disposal Instruction
Altri manuali Sunvic Termostato
Sunvic
Sunvic SunStatRF Manuale utente
Sunvic
Sunvic SunPro2000 Manuale utente
Sunvic
Sunvic TLX 6001RFPv Manuale di istruzioni
Sunvic
Sunvic TLX 7506 Manuale utente
Sunvic
Sunvic SunStat Istruzioni per l'installazione
Sunvic
Sunvic TLX RFP Manuale utente
Sunvic
Sunvic TLX 7506 Manuale utente
Sunvic
Sunvic TLX1009 Manuale utente
Sunvic
Sunvic TLX 6501 Manuale utente
