Super-Pro VAPOR-B1 Manuale utente
Specs
Input voltage 120 Volts AC
Maximum amperage 14.5 amps @ 120 VAC
Humidity control range 20 – 90% rH
Separate Day & Night settings *photocell control
Humidity accuracy +/- 5% rH
Humidity dead-band (hysteresis) 5% rH
Weight < 1 lbs
Dimensions 3” x 6” x 3.5”
VAPOR-B1
humidity controller
Basic Description
The VAPOR-B1 is a humidity controller that can control either
a dehumidifier or humidifier. Once the VAPOR-B1 is
connected to a power source, and the humidification device is
connected to the VAPOR-B1 power outlet, the device
connected will be automatically controlled by the settings on
the VAPOR-B1.
The user can choose to have different Day and Night humidity
settings which will be automatically switched to the correct
mode by the built-in photocell. The knobs make it easy to
adjust the settings and provide a quick visual verification of the
current set-points. The LEDs on the front of the unit will turn
ON and OFF to show the user the current conditions of the
VAPOR-B1.
NOTE: This unit is water-resistant however…
Keep it away from water!!! It is NOT WATER PROOF.
Installation
Plug the unit into a standard NEMA 5-15 wall outlet. A 120 volt
power supply is required. For more permanent installations,
the mounting tab at the top of the unit can be secured to a
wall.
Ensure that the device being connected to the VAPOR-B1 has
the proper voltage and will not exceed the maximum
amperage rating of this unit. Connect the device to be
controller into the power outlet on the front of the unit.
NOTE: If you are trying to control multiple devices, a
power expansion module can be used to increase
the amount of power load that can be controlled.
DO NOT EXCEED THE MAXIMUM RATING!!!
Selecting Dehumid or Humid Mode
Before using the unit, the user must decide if they are using it
for a DE-humidify or HUMIDIFY control. The 2 knobs on the
unit are used to select the desired mode.
To select Dehumidify (lower humidity levels / rh-): Connect
the unit to power. Rotate both knobs fully COUNTER-
clockwise. After a couple seconds the LEDs on the front of the
unit will start flashing On / Off. After the LEDs stop flashing,
the selected mode is indicated by the LED that remains
illuminated. (*Verify the rh- mode is ON.)
To select Humidify (raise humidity levels / rh+): Connect
the unit to power. Rotate both knobs fully clockwise. After a
couple seconds the LEDs on the front of the unit will start
flashing On / Off. After the LEDs stop flashing, the selected
mode is indicated by the LED that remains illuminated. (*Verify
the rh+ mode is ON.)
* Once the correct mode is selected, the user can now set the
desired humidity settings using the two knobs normally.
Changing Settings
Use the knobs on the front of the unit to adjust the DAY and
the Night humidity settings*. The photocell will automatically
use the correct setting depending on the lighting level. When
the humidity of the area exceeds the humidity set-point, the
device connected to the power outlet will be activated. Since
the humidity control has a dead-band setting of 5% rH, the
power outlet will remain activated until the humidity is lowered
by 5% rH. When the outlet is powered, the Output ON LED
will be ON.
*This example describes the Dehumidify mode. When in
Dehumidify mode, the setting is the maximum humidity of the
area to be controlled. For Humidify mode, it is the minimum
humidity of the area to be controlled.
Q & A
How can I tell if the photocell is working? There is a built-in
30 second time delay for the photocell to change status. A
green LED on the top RIGHT edge of the unit that says
“Daytime” will light up when the photocell is in Daytime mode.
Can I connect more than one device to the unit. Yes… As
long as the total amperage of the devices connected to the
unit do not exceed the maximum rating of the unit. We
recommend the total amps not to exceed 75% of the rating.
The humidity of the area does not seem to be correct? The
sensor is located on the bottom on the unit in the protective
plastic “cage”. Ensure the unit is not being affected by other
factors such as direct sunlight exposure or areas that may not
have good air movement.
What if there is no power? Ensure the unit is getting power.
Check the device that is connected to the unit by plugging it
directly into a known power supply. If the unit will not turn on
and no LEDs will illuminate, contact your distributor for repair
and warranty issues.
made in china
Altri manuali Super-Pro Controllori
