superbrightleds PLC-F Manuale utente
Landscape LED Path Light with Cone Shade
Important: Read all instructions prior to installation.
User Manual
Part Number:
Landscape LED Path Light with
Cone Shade
PLC-F
Installation Manual
Rev Date: V1 02/05/2018Rev Date: V1 02/05/2018
Trouble Shooting
PLC-F
PLC-F-WWCOB
Problem Possible Cause Solution
Fixture does
not light
1. There is no power to 12V power
supply.
2. The quick connector does not
make contact with wires.
3. The primary landscape wire is not
connected to 12V power supply.
4. There is a disconnection in prima-
ry landscape wire.
5. Minimum load not exceeded.
1. Check the outlet to 12V power supply and ensure that a breaker or GFCI
circuit has not been tripped.
2. Check the wiring of quick connector that it is screwed tightly, piercing
through wire insulation to make solid contact with wire conductors.
3. Check primary landscape wire connection to 12V power supply.
4. Follow wires from xture to 12V power supply to ensure a continuous run
and/or follow wires between problematic xture and working xture.
5. Ensure that your power supply does not have a minimum load requirement.
Consult the power supply specications or manual.
Light ickers
(one xture)
1. There is a loose connection with
quick connect on primary land-
scape wire.
1. Tighten quick connects, and ensure contacts are piercing through wire
insulation to make solid contact with wire conductors.
Light ickers
(all xtures)
1. There is a loose connection to 12V
power supply.
2. Minimum load not exceeded.
1. Disconnect power to 12V power supply and ensure primary landscape wire
connections are securely fastened and not in contact with other wire.
2. Ensure that your power supply does not have a minimum load requirement.
Consult the power supply specications or manual.
Light is dim 1. Maximum load of 12V power
supply has been exceeded.
2. Recommended distance per land-
scape wire guage exceeded.
1. Check for other lights or other load on same system and/or increase 12V
power supply wattage.
2. Increase primary landscape wire gauge size to recommended guidelines.
* For superbrightleds.com technical help call 866-590-3533
* For superbrightleds.com technical help call 866-590-3533 or use our online chat service.
User Manual
Part Number:
Installation Instructions
Landscape LED Path Light with Cone Shade
Important: Read all instructions prior to installation.
Rev Date: V1 02/05/2018
SBL Part No. Description
*WWN-2212 Silicone Filled Wire nut
SFT-20 Self Fusing Silicone Tape
WP14-2DB 14 Guage Landscape Wire
WP12-2DB 12 Guage Landscape Wire
Safety and Notes Parts Included
Recommended Accessories
Assembly
Dimensional Drawings
1 - Low Voltage Path Light
1 - Mounting Stake
*Note: Cutting quick connects will not
void warranty. Product exchange only.
1. Lay xtures out as they will be installed.
2. Run landscape wire (WP14-2DB or WP12-2DB available at
superbrightleds.com) from 12V supply past each light. Wire must be
within 8” of mounting stake to allow power connections to be made.
3. Use quick connects supplied with each xture to connect each light
to the landscape wire.
4. Using a small shovel and/or water, loosen the ground where xture will be
installed. Press stake into ground.
Note: Do not use a hammer or exert excessive force on the xture while
installing as this may cause damage.
Note: DO NOT force stake using xture as grip. Push from stake only.
5. Turn on 12V supply and ensure all xtures are working. If one or more individual
xtures are not working, check each connection to landscape wire. If none
come on, check connection to the 12V supply. It is recommended to wrap all
connections in electrical or self-fusing tape (available at superbrightleds.com).
6. Bury landscape wire, xture pigtails, and connectors. A depth of 3” is
recommended. Wires and connectors can also be covered by mulch or stone.
Low Voltage
Landscape Wire
Quick Connects
Slot
Power
Supply
Assemble xtures as shown
below. Run power wires
through slot in stakes.
160.66mm
6.33in
406.48mm
16.00in
115.19mm
4.54in
GY6.3 BULB NOT INCLUDED
160.66mm
6.33in
406.48mm
16.00in
115.19mm
4.54in
GY6.3 BULB NOT INCLUDED
160.66mm
6.33in
406.48mm
16.00in
115.19mm
4.54in
GY6.3 BULB NOT INCLUDED
PLC-F
PLC-F-WWCOB
G4 Bulb
• For use with OUTDOOR, low-voltage
landscape lighting systems ONLY.
• NOT FOR USE with submersible or pool/
spa equipment.
• Do not submerge in water, the product
can be damaged.
• This light xture is only suitable for a
12~15 Volt AC or DC power supply.
Do not exceed 80% of power supply
max output.
• Use landscape wire: SBL Product #:
WP14-2DB or WP12-2DB
• This light uses a G4 bulb, which is
not included.
Questo manuale è adatto per i seguenti modelli
1
Altri manuali superbrightleds Illuminazione del paesaggio
superbrightleds
superbrightleds XS2 Series Manuale utente
superbrightleds
superbrightleds SPL-xKxW-60BR Series Manuale utente
superbrightleds
superbrightleds PLTT-WW1BK Manuale utente
superbrightleds
superbrightleds PLMB-W4BK Manuale utente
superbrightleds
superbrightleds PLDT-W4BK Manuale utente
superbrightleds
superbrightleds PLDT-W2BK Manuale utente
superbrightleds
superbrightleds PLMB-W2BK Manuale utente
superbrightleds
superbrightleds PLST-W2BK Manuale utente
superbrightleds
superbrightleds PLST-W4BK Manuale utente
superbrightleds
superbrightleds PLMB-xK3BR Manuale utente
Manuali Illuminazione del paesaggio popolari di altre marche
Cooper Lighting
Cooper Lighting MCGRAW-EDISON WBG Manuale utente
Cooper Lighting
Cooper Lighting Invue 42 - 175W Manuale utente
Saxby Lighting
Saxby Lighting Islay 68784 Manuale
LIGMAN
LIGMAN EU-10016-3 Manuale utente
Cooper Lighting
Cooper Lighting McGraw-Edison ZD Credenza Manuale utente
LIGMAN
LIGMAN KI-60475 Manuale utente
