Superior Xtreme Series Manuale utente

Xtreme ™ Series

Touchscreen Manual

Software version 4.2.XX

Why Would You Go Anywhere Else?

Superior PAPER HANDLING SOLUTIONS

Have this information ready when calling in about your equipment:

Model: Serial #:

PLC firmware version: HMI firmware version:

Warranty Start Date:

Illustrations in this guide are for reference only and may depict optional features that are available

at additional costs.

Superior Paper Handling Solutions, Inc.

14414 21st Avenue North

Plymouth, Minnesota 55447 – USA

Tel. 763-546-9140

Fax. 763-546-8883

Email. [email protected]

Web. www.Superior-PHS.com

CONTENTS

SCREEN LAYOUT .......................................................................................................... 3

MECHANICAL PUSH BUTTONS .................................................................................... 4

POWER UP SCREEN ..................................................................................................... 4

RUN SCREEN ................................................................................................................. 5

5_JOB SETUP SCREEN ..................................................................................... 6

1_SETUP 1 SCREEN ...................................................................................................... 7

2_SETUP 2 SCREEN ...................................................................................................... 8

3_SETUP 3 SCREEN ...................................................................................................... 9

4_COUNTERS SCREEN ................................................................................................. 9

6_DROPPER SELECT SCREEN .................................................................................. 10

BD/RD SELECT SCREEN ................................................................................. 10

MDRD SELECT SCREEN ................................................................................ 11

SD DROPPER SELECT SCREEN ................................................................... 12

2 STAGE DROPPER SELECT SCREEN ......................................................... 13

7_INPUTS 1 .................................................................................................................. 14

8_INPUTS 2 .................................................................................................................. 14

9_OUTPUTS 1............................................................................................................... 14

10_OUTPUTS 2............................................................................................................. 14

MESSAGE and ERROR DISPLAYS .............................................................................. 15

OPERATORS NOTE PAGE

page 2

RUN COUNTER DROPPER INPUTS/OUTPUTS SETUP

POWER UP

Brings you to the POWER UP Screen

Brings you to the RUN Screen

Brings you to the previous numbered Screen

Brings you to the next numbered Screen

Brings you back to the main

numbered Screen you started from

BELOW COMMANDS WORK WITHIN THE

NUMBERED SCREENS 1-10:

Why Would You Go Anywhere Else?

page 3

Superior PAPER HANDLING SOLUTIONS

HMI and PLC firmware versions

HOME [POWER UP SCREEN]

RUN: Takes operator directly to Run Screen

COUNTER: Takes operator directly to 4-Counters Screen

DROPPER: Takes operator directly to 6-Dropper Select Screen

INPUTS/OUTPUTS: Takes operator directly to 7-Inputs 1 Screen

SETUP: Takes operator directly to1-Setup 1 Screen

NOTE: All settings from previous power down will be retained

page 4

Stop/Reset Button If an error occurs this push button will illuminate.

It will also light when the stop is used to stop the feeder. Clear all errors if

present and push this button to move the feeder to a Ready stage.

Cycle Button If the feeder is Ready than this push button will illuminate.

From here pressing the button will command a start cycle.

Jog Button The feeder will advanced when the Jog button is pressed.

The feeder will continuously run when the jog button is activated. This

option is typically used when setting up product in the feeder or clearing

any product under the Separator. While holding down the Jog button, you

can adjust the Separator and feed product until the product feeds consistently.

MECHANICAL FRONT PANEL PUSH BUTTONS

Why Would You Go Anywhere Else?

RUN

JOB SET: Takes operator directly to 5-Job Set Screen

MODE [LOCAL or SYSTEM]: Local Mode is the standard

setting. Push to toggle between System and Local Mode.

To run the feeder in a stand alone operation this

must show Local Mode. (Green displayed)

CONTINUOUS MODE: Display only. If the feeder is in

Continuous Mode this display will appear. (Green displayed)

CYCLE SPEED: Allows user to set feeder speed. 100 is

equal to maximum speed.

RESET COUNT: Pressing this button will reset the Actual Count display. If the feeder has stopped in the

middle of completing a Batch, pressing this reset will start the batch count over.

BATCH SIZE: Pressing this button will allow a user to set the batch size.

[KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

ACTUAL COUNT: Display only. Displays the count as the feeder is running. It will count up to your batch

size and reset to zero when the batch is complete. If the feeder errors or stops before the batch cycle

completes, this number will reflect what has been counted. Starting the feeder again will finish the batch.

NOTE: If using the EXT I/O to remotely STOP, RESET and CYCLE the feeder; Upon an error

or remote stop, the Actual Count will always reset to zero and not retain the partial batch. If required to retain

the partial batch, then remotely PAUSE/RESUME the feeder through the EXT I/O.

Superior PAPER HANDLING SOLUTIONS

page 6

NOTE: When the Job Set is turned on and the Total Count reaches zero a display will appear

stating the Job Set is complete. In order to initiate another batch cycle you must turn the Job Set off.

5 - JOB SET

DROPPER: Takes operator directly to 6-Dropper Select

Screen

TOTAL COUNT: Enter the Job size. [KEYBOARD ENTRY

-MIN/MAX WITHIN KEYBOARD DISPLAY ]

JOB SET ON/OFF: When using the Job Set function, you

will be able to set a Total Count that will stop the feeder

when reached (i.e. while batching 50 piece sets, you only

5000 sheets batched out)

NOTE: If Total Count is at zero when Job Set is turned on

it will display Job Complete. Enter count first

ACTUAL COUNT: Display only. Does not function in Continuous Mode. This will display the Actual Count

where the feeder is at within a batch. Mirrored display to the Actual Count from the Run Screen.

BATCH COUNT: Display Only. Does not function in Continuous Mode. This will display the number of

batches completed by the feeder. The Reset button allows this field to clear to zero when pressed.

NOTE: The Run Screen does not display accumulation of Batch Counts. Because this field doesn’t require

the Job Set to be turned on, acquiring Batch Counts can be retrieved in this 5 - Job Set Screen even when

the Job Set function is not being used. The 4 - Counters Screen also displays the Batch Count field. They

are also mirrored displays and the Reset buttons from either screen will zero it.

COUNT to TOTAL : Display only. Displays the quantity left until the Job Set is complete.S

Why Would You Go Anywhere Else?

1 - SETUP 1

TRIGGER DELAY: Enter the delay time in seconds

[KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD

DISPLAY ] Used only with trigger sensor or external

CYCLE input.

SKIP FLIGHT: Enter the number of skips per trigger.

[KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD

DISPLAY ] Used to skip the feeder from firing every

on every trigger. (i.e every third pocket)

SLOW START or STOP function: The next three functions control the settings with regards to

setting a slower speed when starting or stopping the feeder. At high speeds this will assist

controlling product to stop consistently and also limit the possible skewing of product as the

feeder advances at startup to a high speed.

SLOW STOP COUNT: Set how many pieces at the end of a batch will run at the slow speed.

[KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

SLOW START COUNT: Set how many pieces at the beginning of a batch will run at the slow speed.

[KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

NOTE: The slow function is turned ON when a value of 1 or greater is recorded at either two of the count

buttons above. In order to not use the slow function, a value of zero must be recorded in those settings.

CONTINUOUS MODE: Set ON/OFF from here. The Run Screen has a display and this button will

illuminate green when the condition is ON.

PAUSE RESUME: Set ON/OFF from here. The Pause/Resume function is used to automatically keep

cycling the feeder with a period of time between batches. This button will illuminate green when the

condition is ON.

PAUSE RESUME TIME: Enter the time value in seconds. This represents the time between the batch

cycles. [KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

SLOW SPEED : Set the speed of the feeder when either the Slow Start or Slow Stop is activated.

[KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ] Recommended to be less than half

the speed recorded in Cycle Speed from the Run Screen.

Superior PAPER HANDLING SOLUTIONS

page 8

2 - SETUP 2

DOUBLE DETECT: Allows user to turn ON/OFF the

Double Detect. Green illumination when ON.

MISS DETECT: Allows user to turn ON/OFF the Miss

Detect. This function monitors that the batch cycle

has completed before receiving another trigger or

remote START. Green illumination when ON

BUSY/DONE VACUUM: Allows user to turn ON/OFF

the Busy/Done or Vacuum function. Read below for

explanation of functions. Green illumination when ON

BUSY/DONE or VACUUM function: There is a particular I/O point in the Ext Interface that will

change its state with regards to whether the motor on the feeder is running or not. Thus a

system controller could monitor the feeder and know when it has completed its batch cycle.

The Vacuum application is considered when an optional venturi vacuum setup is purchased

with the feeder. This allows the vacuum to only operate when the feeder is running. EITHER

one condition or the other is used as a scenario. Both situations use the same I/O point.

TIME OUT function: The next three functions control the settings with regards to setting the

Time Out function. This is used to monitor the sheet sensor for clear and block conditions.

(Feeder empty or Jammed conditions)

TIME OUT EYE CLEAR: Enter the time in seconds. An error will occur if the sheet sensor stays open

the duration of time set. [KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

TIME OUT EYE BLOCKED: Enter the time in seconds. An error will occur if the sheet sensor stays

blocked the duration of time set. [KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

NOTE: The time set for blocked has to be large enough to allow one piece to advance completely

through the sheet sensor. This may have to set bigger for large product running at slow cycle speeds.

LOW STACK function: The next three functions control the settings with regards to setting the

Low Stack function. This function is only used if the feeder was purchased with a Low Stack eye.

LOW STACK WARN: Set how many pieces once the Low Stack eye clears to when the warning amber

light will flash (Requires purchase of light tower with feeder) [KEYBOARD ENTRY-MIN/MAX WITHIN

KEYBOARD DISPLAY ]

LOW STACK HALT: Set how many pieces once the Low Stack eye clears to when the feeder will stop.

Product must be filled again to cycle the feeder. [KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD

DISPLAY ]

TIME OUT: Allows the user to turn ON/OFF the Time Out function

LOW STACK : Allows the user to turn ON/OFF the Low Stack function. Green illumination when ON

. Green illumination when ON

Why Would You Go Anywhere Else?

3 - SETUP 3

and cycles at the speeds programmed below.

TAMPER RETURN DELAY: Enter the return time in seconds

for the actuator arm. [KEYBOARD ENTRY-MIN/MAX

WITHIN KEYBOARD DISPLAY ]

TAMPER EXTEND DELAY: Enter the extend time in seconds

for the actuator arm. [KEYBOARD ENTRY-MIN/MAX

WITHIN KEYBOARD DISPLAY ]

NOTE: General settings will have these extending and

returning times around .2-.5 seconds, dependent on the

air volume and tamping speed requirements.

MANUAL CYCLE: Manually activates the wedge tamper

WEDGE TAMPING function: This function along with the mechanical assembly will tap the

product while stacked in the hopper. This assists in funneling the product down into the separator

assembly for better performance.

# OF SHEETS BETWEEN TAMPS: Set how many pieces will run between tamping cycles.

[KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

TAMPS # OF TIMES : Set how many times the tamper will extend and return during its tamping cycle.

[KEYBOARD ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

TAMPER DISABLED : Turn the Tamper ON/OFF. Green Illuminate when the function is enabled.

NOTE: If you did not purchase a Wedge Tamper, disregard this setup page and leave it disabled.

4 - COUNTERS

products through the sheet counter. RESET button sets

to zero

BATCH COUNTER: Display only. Counts the number of

batches completed through the sheet counter. RESET

button sets to zero

TOTAL PIECE COUNTER: Display only. Counts the

number of products through the sheet counter.

NOTE: This Display is not resettable. It will reflect the

number of pieces through the feeder at any given time

PIECE COUNTER: Display only. Counts the number of

Superior PAPER HANDLING SOLUTIONS

page 10

6 - DROPPER SELECT

BD/RD DROPPER: Allows user to turn ON/OFF. Green

illumination when ON.

BD/RD DROPPER SETUP: Takes you to Setup page.

SD DROPPER: Allows user to turn ON/OFF. Green

illumination when ON.

SD DROPPER SETUP: Takes you to Setup page.

MDRD DROPPER: Allows user to turn ON/OFF. Green

illumination when ON.

MDRD SETUP: Takes you to Setup page.

2 STAGE SETUP: Takes you to Setup page.

NOTE: If you did not purchase a dropper, disregard this setup page and leave all OFF.

NOTE: Only one Dropper can be ON at one time.

BD/RD SETUP

BACK: Takes user back to 6 - Dropper Select Screen

DROPPER EXTEND DELAY: Sets the time in seconds

the period the dropper stays open. [KEYBOARD ENTRY

-MIN/MAX WITHIN KEYBOARD DISPLAY ]

FEEDER DELAY: Sets the time in seconds the feeder

will delay before feeding the next batch. [KEYBOARD

ENTRY-MIN/MAX WITHIN KEYBOARD DISPLAY ]

MANUAL CYCLE: Cycles the dropper once.

Indice

Altri manuali Superior Schermo tattile

Superior

Superior Xtreme XM Series Manuale utente

Manuali Schermo tattile popolari di altre marche

Elecro Engineering

Elecro Engineering Poolsmart Plus Istruzioni per l'installazione

Johnson Controls

Johnson Controls IQ4 HUB Manuale utente

Elo TouchSystems

Elo TouchSystems ET2270L Manuale utente

Elo TouchSystems

Elo TouchSystems ET1002L Manuale utente

Elo TouchSystems

Elo TouchSystems 3201L Manuale utente

Duratec

Duratec S15 Manuale utente

Crestron

Crestron TPMC-3SM Manuale utente

Racelogic

Racelogic MFD Touch Manuale utente

J2 580 Guida utente

HAI

HAI OmniTouch 10p Manuale utente

panel

panel PC PSR108-FM Series Manuale utente

Tipro

Tipro FREE+ Manuale utente

Systemline

Systemline Commander Manuale utente

Interactive Technologies

Interactive Technologies Insite Manuale utente

GVision

GVision Legacy Manuale utente

BeiJer

BeiJer T21C-C24 Manuale utente

Advantech

Advantech ITM-5117 Series Manuale utente

Edge

Edge CS Manuale utente