Supermicro Super C9X299-PGF Manuale utente

C9X299-PGF

C9X299-RPGF

C9X299-PGF/-RPGF QUICK REFERENCE GUIDE Product Safety Information

Standardized Warning Statements

Motherboards

About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user of situations which can potentially

cause a bodily injury. Should you have questions or experience di󰀩culty, contact Supermicro's Technical Support De-

partment for assistance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the Supermicro chassis.

Battery Handling

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-

lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメーカーが推奨する型、または同等のもの

を使用下さい。使用済電池は製造元の指示に従って処分して下さい。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理

廢棄舊電池。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理

废旧电池。

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한

종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.









WARNING: This product can expose you to chemicals including

lead, known to the State of California to cause cancer and birth

defects or other reproductive harm. For more information, go

to www.P65Warnings.ca.gov.

C9X299-PGF/-RPGF QUICK REFERENCE GUIDE 限用物質含有情況標示聲明書

限用物質含有情況標示聲明書

Declaration of the Presence Condition of the Restricted Substances Marking

限用物質含有情況標示聲明書

設備名稱：主機板

Motherboard

,型號（型式）:

C9X299-PGF,C9X299-RPGF

單元Ｕnit

限用物質及其化學符號

鉛Lead

(Pb) 汞Mercury

(Hg) 鎘Cadmium

(Cd)

六價鉻

Hexavalent

chromium

(Cr+6)

多溴聯苯

Polybrominated

biphenyls

(PBB)

多溴二苯醚

Polybrominated

diphenyl ethers

(PBDE)

主機板

(Motherboard)

－○ ○ ○ ○ ○

備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準

值。

備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。

備考3.〝－〞係指該項限用物質為排除項目。

Equipment name

Type designation (Type)

Restricted substances and its chemical symbols

Declaration of the Presence Condition of the Restricted Substances Marking

Note 1

：

“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the

reference percentage value of presence condition.

Note 2

：

“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.

Note 3

：

The “−” indicates that the restricted substance corresponds to the exemption.

C9X299-PGF/-RPGF QUICK REFERENCE GUIDE AMI BIOS POST Codes

AMI BIOS POST Codes

About AMI BIOS POST Codes

The table below lists some of AMI BIOS POST codes for C9X299-PGF/-RPGF. For more information, refer to https://

www.supermicro.com.tw/manuals/other/AMI_AptioV_BIOS_POST_Codes_for_SM_Motherboards.pdf.

Code Description

0x32 CPU post-memory initialization is started

0x55 No Memory detected or memory failed

0x63 CPU DXE initialization is started

0x69 North Bridge DXE initialization is started

0x70 South Bridge DXE initialization is started

0x92 PCI Bus initialization is started

0x99 Super IO Initialization

0x9A USB initialization is started

0xA0 IDE initialization is started

0xA9 Boot into BIOS setup menu

0xAE Legacy Boot event

0xB2 Legacy Option ROM Initialization

0xB4 USB hot plug

0xD6 No console output devices are found

0xD7 No console input devices are found

0xF2 Recovery process started

0xF9 Recovery capsule is not found

C9X299-PGF/-RPGF QUICK REFERENCE GUIDE M.2 Device Installation/Removal Instructions

M.2 Device Installation and Removal Instructions

M.2 Device Installation M.2 Device Removal

C9X299-PGF/-RPGF QUICK REFERENCE GUIDE Notes

Notes

C9X299-PGF/-RPGF

Quick RefeRence Guide Rev. 1.0a

SUPERMICR R

BIOS

LICENSE

MAC CODE

IPMI CODE

BAR CODE

C9X299-PGF REV:1.01

PCIE M.2 CONNECTOR 2

PCIE M.2 CONNECTOR 1

SPEAKER:1-4

BUZZER:3-4

JD1

CLEAR CMOS

U.2 CONNECTOR 1

U.2 CONNECTOR 2

I-SATA5

I-SATA4

I-SATA3

USB 4/5 (3.0)

USB 2/3

USB 0/1

PCH SLOT2 PCI-E 3.0 X1

NMI

USB 10/11 (3.0)

CPU SLOT1 PCI-E 3.0 X8 (IN X16)

CPU SLOT7 PCI-E 3.0 X16

PWR LEDHDD LED XPWR ON OH/FF NIC1NIC2RST X

CPU SLOT3 PCI-E 3.0 X8 (IN X16)

CPU SLOT5 PCI-E 3.0 X8 (IN X16)

I-SATA2 I-SATA0

I-SATA1

DIMMA1

DIMMB2

DIMMB1

DIMMA2

1-2 ENABLE

2-3 DISABLE

JPAC1:AUDIO

HD AUDIO

USB 8/9 (3.1)

LAN2 LAN1

USB 6/7 (3.1)

DIMMD2

DIMMD1

DIMMC2

DIMMC1

KB/Mouse

CLOSE 1st

OPEN 1st

JF1

LGA2066

VGA

LED1

JRK1

SP1

JTPM1

JPI2C1

JL1

JPAC1

JWD1

JPG1

JPME2

FAN5

FAN3

FAN2

FAN4 FAN1

JBT1

JSD1

JIPMB1

JSTBY1

MH15

MH12

MH14

JD1

J3701

LED6903

LED6904

LED7201

JPW1

JPW2

JCOM1

PCH

LAN

CTRL

RESET

POWER

JPB1

JPW3

Motherboard Layout and Features

=mounting hole

LGA 2066

I/O BACK PANEL

Package contents

• One Supermicro Motherboard

• Four SATA Cables

• One Quick Reference

• One I/O Shield

• One Driver CD

Connector Description

B2 Onboard Battery

FAN1 ~ FAN5 System/CPU Fan Headers (FAN1 and FAN2: CPU fans)

HD AUDIO High Denition Audio (back panel ports)

I-SATA0~5 (Intel X299) Serial ATA (SATA 3.0) Ports 0~5 (6Gb/sec)

J3701 Front Panel Audio Header

JCOM1 COM1 Port Header

JD1 Speaker/Buzzer (Pins 1~4: external speaker, Pins 3~4: buzzer)

JF1 Front Control Panel Header

JIPMB1 4-pin External I2C Header (for an IPMI card)

JL1 Chassis Intrusion Header

JPI2C1 Power Supply SMBus I2C Header

JPW1 24-pin ATX Main Power Connector (Required)

JPW2 +12V 8-pin CPU Power Connector (Required)

JPW3 +12V 4-pin CPU Power Connector (Required)

JRK1 Intel RAID Key Header

JSD1 SATA DOM (Disk On Module) Power Connector

JSTBY1 Standby Power Header

JTPM1 Trusted Platform Module (TPM) Header

LAN1, LAN2 (back panel) LAN1: 5Gb LAN Port. LAN2: 1Gb LAN Port (LAN2: Shared IPMI Port)

PCIE M.2 CONNECTOR 1, 2 PCIe M.2 Connectors 1 and 2 (small form factor devices and other portable

devices for high speed NVMe SSDs)

SP1 Internal Buzzer/Speaker

U.2 CONNECTOR 1, 2 U.2 Connectors 1 and 2, for 2.5” SSD Drives

USB 0/1, 2/3 Front Access USB 2.0 Headers

USB 4/5 Back Panel USB 3.0 Ports

USB 6/7, 8/9 Back Panel USB 3.1 Ports (USB8: Type A, USB9: Type C)

USB 10/11 (3.0) Front Access USB 3.0 Header

VGA Back Panel VGA Port

Jumpers and Connectors

Jumpers

Jumper Description Default

CLEAR CMOS Clear CMOS Switch Push Button Switch

JBT1 Clear CMOS (onboard) Short Pads to Clear CMOS

JPAC1 Audio Enable Pins 1-2 (Enabled)

JPB1 IPMI Function Pins 1-2 (Enabled)

JPG1 VGA Enable/Disable Pins 1-2 (Enabled)

JPME2 Intel Manufacturing Mode Pins 1-2 (Normal)

JWD1 Watch Dog Function Enable Pins 1-2 (RST)

POWER BUTTON Internal Power Button Push Button Switch

RESET BUTTON Onboard System Reset Button Push Button Switch

Connectors

ContaCt InformatIon

• www.supermicro.com (Email: [email protected])

• Manuals: http://www.supermicro.com/support/manuals

• Drivers & Utilities: https://www.supermicro.com/wdl/driver/

• Safety: http://www.supermicro.com/about/policies/safety_information.cfm

This motherboard supports a single Intel® CoreTM i9 7900X/9900X/10900X Series processor, up to 256GB of Un-

bu󰀨ered (UDIMM) non-ECC DDR4 memory, with speeds of up to 2666MHz (2DPC) ~ 2933MHz (1DPC) in eight

288-pin memory slots. Populating these DIMM slots with a pair of memory modules of the same type and size will

result in interleaved memory, which will improve memory performance.

Notes: 1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates, please

refer to our website at http://www.supermicro.com/products/motherboard.

2) Always connect the power cord last, and always remove it before adding, removing or changing any hardware components.

3) 2933MHz is supported by Intel Core i9 10980XE/10940X/10920X/10900X Series processors only.

4) Memory overclocking support depends on the capability of CPU and memory.

LED Indicators

LED Description Color/State Status

LED1 Status Code LED Digital Readout See User's Manual

LED7201 Onboard Standby PWR LED Green: Solid on Power on

LED6903 M.2 Connector 2 SSD Active LED Green: Solid on M.2 Device Active

LED6904 M.2 Connector 1 SSD Active LED Green: Solid on M.2 Device Active

LED Indicators

CPU & Memory Support

Towards the CPU

DIMM Memory Installation

Towards the CPU

DIMMB1 (Gray Slot)

DIMMA1 (Gray Slot)

DIMMA2 (Black Slot)

DIMMB2 (Black Slot)

DIMMD1 (Gray Slot)

DIMMC1 (Gray Slot)

DIMMC2 (Black Slot)

DIMMD2 (Black Slot)

Memory Population Guidelines

When installing memory modules, the DIMM slots should be populated in the following order: DIMMA1, DIMMB1,

DIMMC1, DIMMD1, then DIMMA2, DIMMB2, DIMMC2, DIMMD2.

• Always use DDR4 DIMM modules of the same size, type, and speed.

• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the slowest DIMM.

Recommended Population (Balanced)

DIMMA1 DIMMB1 DIMMC1 DIMMD1 DIMMA2 DIMMB2 DIMMC2 DIMMD2 CPU Support/

DIMM Channel

Total

System

Memory

4, 8, 16,

32GB

4, 8, 16,

32GB N/A N/A N/A N/A N/A N/A Core i9 7900X/9900X/10900X Series,

Dual channel Up to 64GB

4, 8, 16,

32GB

4, 8, 16,

32GB

4, 8, 16,

32GB

4, 8, 16,

32GB N/A N/A N/A N/A Core i9 7900X/9900X/10900X Series,

Dual channel Up to 128GB

4, 8, 16,

32GB

4, 8, 16,

32GB

4, 8, 16,

32GB

4, 8, 16,

32GB

4, 8, 16,

32GB

4, 8, 16,

32GB

4, 8, 16,

32GB

4, 8, 16,

32GB

Core i9 7900X/9900X/10900X Series,

Quad channel Up to 256GB

* Please note that 32GB is supported by Core i9 10980XE/10940X/10920X/10900X Series processors only.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Supermicro Hardware per computer

Supermicro

Supermicro AOC-STG-i4T Manuale utente

Supermicro

Supermicro AOC-SMG3-2H8M2 Manuale utente

Supermicro

Supermicro BPN-SAS3-833A Manuale utente

Supermicro

Supermicro SBI-7127R-S6 Manuale utente

Supermicro

Supermicro C9Z790-CG Manuale utente

Supermicro

Supermicro AOC-USAS-S4i Manuale utente

Supermicro

Supermicro SBI-7426T-S3 Manuale utente

Supermicro

Supermicro AOC-URG4N4-b2XT Manuale utente

Supermicro

Supermicro A3SEV-2C-LN4 Manuale utente

Supermicro

Supermicro SuperBlade SBI-420P-4T2N Manuale utente

Supermicro

Supermicro AOC-PG-i2+ Manuale utente

Supermicro

Supermicro BPN-SAS3-825TQ Manuale utente

Supermicro

Supermicro AOC-AG-i4S Manuale utente

Supermicro

Supermicro BPN-SAS3-743A Manuale utente

Supermicro

Supermicro BPN-NVMe3-216N-S4 Manuale utente

Supermicro

Supermicro SC825 Air Shroud Manuale utente

Supermicro

Supermicro B13SEE-CPU-25G Manuale utente

Supermicro

Supermicro SuperServer SYS-510D-4C-FN6P Manuale utente

Supermicro

Supermicro B2SC1-CPU Manuale utente

Supermicro

Supermicro BPN-SAS3-815TQ Manuale utente

Supermicro

Supermicro AOC-SHG3-4M2P Manuale utente

Supermicro

Supermicro AOC-SLG4-4E4T Manuale utente

Supermicro

Supermicro X11DPI-N-O Manuale utente

Supermicro

Supermicro BPN-SAS3-842TQ Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente