suprema Enclosure ENCR-10 Manuale utente
Enclosure
INSTALLATION GUIDE
Version 1.00
English
EN 101.00.ENCR-10 V1.00A
2
Safety information
Safety information
Please read this safety instructions before you use the product to prevent injury to yourself and others and to prevent
property damage. The term 'product' in this manual refers to the product and any items provided with the product.
Instructional icons
Warning: This symbol indicates situations that could result in death or severe injury.
Caution: This symbol indicates situations that may result in moderate injury or property damage.
Note: This symbol indicates notes or additional information.
Warning
Installation
Do not install or repair the product arbitrarily.
• This may result in electric shock, fire, or product damage.
• Damages caused by any modifications or failure to follow installation instructions can void the manufacturer’s warranty.
Do not install the product in a place with direct sunlight, moisture, dust, soot, or a gas leak.
• This may result in electric shock or fire.
Do not install the product in a location with heat from an electric heater.
• This may result in fire due to overheating.
Install the product in a dry location.
• Humidity and liquids may result in electric shock or product damage.
Do not install the product in a location where it will be affected by radio frequencies.
• This may result in fire or product damage.
Operation
Keep the product dry.
• Humidity and liquids may result in electric shock, fire, or product damage.
Do not use damaged power supply adaptors, plugs, or loose electrical sockets.
• Unsecured connections may cause electric shock or fire.
Do not bend or damage the power cord.
• This may result in electric shock or fire.
3
Safety information
Caution
Installation
Do not install the product under direct sunlight or UV light.
• This may result in product damage, malfunction, discoloration, or deformation.
Do not install the power supply cable in a location where people pass by.
• This may result in injury or product damage.
Do not install the product near magnetic objects, such as a magnet, TV, monitor (especially CRT), or speaker.
• The product may malfunction.
Operation
Do not drop the product or cause impacts to the product.
• The product may malfunction.
Do not store your product in very hot or very cold places. It is recommended to use the product at
temperatures from 0 °C to 50 °C.
• The product may malfunction.
When cleaning the product, mind the following.
• Wipe the product with a clean and dry towel.
• If you need to sanitize the product, moisten the cloth or the wipe with a proper amount of rubbing alcohol and gently
clean all exposed surfaces including the fingerprint sensor. Use rubbing alcohol (containing 70% Isopropyl alcohol) and a
clean, non-abrasive cloth like lens wipe.
• Do not apply liquid directly to the surface of the product.
Do not use the product for anything other than its intended use.
• The product may malfunction.
4
Introduction
Introduction
Components
Enclosure
(ENCR-10)
Fixing screws for
the enclosure x4 PVC Anchor x4 Fixing screws for
the device x6 Cable Tie x6
Core Terminal
Fixing screws for
the power supply
cable
Earth Cable
• Components may vary according to the installation environment.
• Fixing screws for the enclosure, CoreStation, and the power supply cable are included in the ENCR-10 package.
Use each screw correctly by following the details below.
- Fixing screws for the enclosure (diameter: 4 mm, length: 25 mm) x 4
- Fixing screws for the device (diameter: 3 mm, length: 5 mm) x 6
- Fixing screws for the power supply cable (diameter: 3 mm, length: 8 mm) x 1
• The battery is sold separately.
5
Introduction
Name of each part
Outside
5
Inside
5
• LED Status indicator & wiring guide labels are provided for CoreStation. For more information regarding
Output Module, visit the Suprema website(https://www.supremainc.com) and refer to the installation guide for
the product.
LED indicator
CoreStation
LED Status
indicator &
wiring guide
label
LED board
Tamper
switch
Battery
mounting
area
Power
supply
Power
distribution
board
Device
mounting
area
6
Installation
Installation
This document describes how to install ENCR-10 and connect ENCR-10's components and devices (CoreStation & Output
Module). For details on other wiring for each device, visit the Suprema website (https://www.supremainc.com) and refer
to the installation guide for the device.
• There is no optimal height for installing ENCR-10 on the wall. Install it to a safe and convenient location for you
to use.
• Fixing screws for the enclosure, CoreStation, and the power supply cable are included in the ENCR-10 package.
Use each screw correctly by following the details below.
- Fixing screws for the enclosure (diameter: 4 mm, length: 25 mm) x 4
- Fixing screws for CoreStatioin (diameter: 3 mm, length: 5 mm) x 6
- Fixing screws for the power supply cable (diameter: 3 mm, length: 8 mm) x 1
Installing CoreStation
Securing the battery
Insert the battery velcro strap into the enclosure and secure the battery.
• Use a backup battery with 12 VDC and 7 Ah or higher. This product was tested with 'ES7-12' battery of
'ROCKET'. It is recommended to use a battery corresponding to 'ES7-12'.
7
Installation
• The battery is sold separately.
• If the dimension of the backup battery is larger than the recommended specification, it may not be able to be
mounted in the enclosure or the enclosure may not close after it is mounted. Also, if the shape and dimension
of the terminals are different, the battery cannot be connected using the cable provided.
151 65
43
94
99
4.75
6.6
0.8
6.35
Backup Battery
Terminal (Unit: mm)
Securing CoreStation
1
Check the position to install CoreStation in the enclosure.
8
Installation
2
After positioning CoreStation in the enclosure, fix it with the fixing screws.
POWER / AUX IN Connection
You can connect an Uninterruptible Power Supply (UPS) to prevent power failure. And a power failure detector or a dry
contact output can be connected to the AUX IN terminal.
9
Installation
• Make sure to use separate power for the access control device and CoreStation.
• Use the correct power specifications (12 V, 3 A).
• Use a backup battery with 12 VDC and 7 Ah or higher. This product was tested with 'ES7-12' battery of
'ROCKET'. It is recommended to use a battery corresponding to 'ES7-12'.
• For details on other wiring such as Ethernet, RS-485, Relay, and Wiegand, visit the Suprema website (https://
www.supremainc.com) and refer to CoreStation installation guide.
• For more information, contact the Suprema technical support team (https://support.supremainc.com).
Indice
Altri manuali suprema Controllori
