SureShade ATF Istruzioni operative e di manutenzione

PO Box 51294 Philadelphia, PA 19115 • Phone: 877.333.8323 • www.sureshade.com

SureShade Installation

1) Mark the position of the mounting clamps (Figs 1 –4)

2) Secure the mounting clamps in place

3) Secure the actuators in place

4) Secure the roller assembly in place

5) Secure the crossbars in place (Fig 5 –6)

6) Set up the electrical system (Fig 7)

7) Preload the canvas (Fig 8)

Position both actuators on top of the hardtop resting on the bottom half of the mounting clamps (Fig 1).

Insert the outer crossbar and/or clamp roller to the actuators and measure across to align the actuators to be

parallel (Fig 2). NOTE –the actuators must be aligned (parallel) to ensure proper functioning of the shade

system.

Fig 1

Fig 2

Insert outer

crossbar

and/or

clamp roller

to actuators

Measure across to

make actuators

parallel

Mark the position of the mounting plates on the hardtop Fig 3 & 3A.

Remove the crossbar, spacer and actuators from the mounting plate so you can drill and secure the mounting

clamp to the hardtop in the marked locations. Secure actuators to the mounting clamps and slide the roller

assembly onto actuators and secure in place (Fig 4).

Slide crossbars onto actuators and secure in place.

Fig 4

Slide roller

assembly onto

actuators

Fig 5

Fig 6

Secure aft crossbar

in place with screw.

Secure mid

crossbar in place

with screw.

Fig 3

Fig 3A

Mark the position of

the mounting plates

The electrical housing is pre-wired and tested before shipping.

The electrical housing controls the retracted and extended positions as well as the synchronization of the actuators’

movement. The synchronization is accomplished by sensors positioned inside the actuator that communicate with the

electrical housing. These sensors, along with the housing software, will keep the two actuators synchronized within ½” of

each other during travel. When an actuator gets ½” ahead of the other actuator the system will shut the faster actuator

down for a split second until the slower actuator catches up and then continues movement again.

1) All control wires for the actuators to the controller and connection from the boat power are supplied with

Deutsch connectors. Once the control wiring for the actuators is properly fed through tubing and fiberglass,

connect one end of the control wire to the actuator and the other end to the electrical housing.

2) Connect the power source to the controller, be sure that the wires providing power to the controller are a 6-8

gauge wire. Too small of a gauge wire can drop voltage and cause an intermittent situation during travel. All

fuses and switch wiring, etc should be to spec with the supplied documentation.

Port control

wire

connection

Starboard

control wire

connection

Fig 7

Power harness

wire connection

from boat

In Fig 8, the canvas comes off the spring-

tensioned roller in the direction of the arrows.

Preload the roller several revolutions by

rotating the canvas and roller in the same

direction that the canvas comes off the roller

(in the direction of the arrows) and zipper to

outer crossbar. Do as many revolutions as

necessary to make sure that the canvas is taut.

Fig 8

Indice

Altri manuali SureShade Attrezzatura nautica

SureShade

SureShade MTF Istruzioni operative e di manutenzione

SureShade

SureShade PTX Power T-Top Shade Guida rapida

SureShade

SureShade RTX Manuale di servizio

SureShade

SureShade MTF Istruzioni operative e di manutenzione

SureShade

SureShade ATF Istruzioni operative e di manutenzione

SureShade

SureShade RTX Manuale di servizio

SureShade

SureShade M3 Manuale di servizio

SureShade

SureShade Power Bimini Istruzioni per l'installazione

SureShade

SureShade Power Bimini Sport Arm Kit Istruzioni per l'installazione

Manuali Attrezzatura nautica popolari di altre marche

Ideal Windlass

Ideal Windlass CWM Guida

Access

Access BIMINI Manuale utente

Floe

Floe VSD 6000 Manuale utente

Faun

Faun C40 Trackway Manuale utente

Exalto

Exalto 240BS Manuale utente

Hobie

Hobie Mirage 360 Manuale utente

Dowco

Dowco V322 CC - 2019 Manuale utente

Humphree

Humphree HCS-5 Manuale utente

Vetus

Vetus BOW4512D Scheda tecnica

Dock Doctors

Dock Doctors SLIDING BOARDING STEP Manuale utente

Mastervolt

Mastervolt Mass Combi 12/2000-100 Istruzioni operative originali

Zattini Group

Zattini Group bamar BOXTRON E14S Guida utente

SeaView

SeaView PM5-FMD-8 Manuale utente

Vetus

Vetus HTANK Manuale utente

Grammer

Grammer AVENTO MSG 65/511 Istruzioni operative

Furuno

Furuno TZTL12F Manuale utente

Harken

Harken 944 Manuale utente

ShoreLand'r

ShoreLand'r DUB 2314 Manuale utente