Suzuki LT-A450XK7 Guida utente
Sep. ’06 Printed in United States (CLA) 28
99505-01017-01E
SUZUKI MANUFACTURING OF AMERICA CORPORATION
FOREWORD
This vehicle has been designed and produced utilizing Suzuki’s most modern tech-
nology. The finest product, however, cannot perform properly unless it is correctly
assembled and serviced. This set-up manual has been produced to aid you in prop-
erly assembling and servicing this vehicle.
Please review this set-up manual carefully before performing any work. Take special
care to properly perform the required assembly and servicing marked by either a
Warning or a Caution. Failure to follow the directions in either of these two (2) cate-
gories could lead to serious problems. and areas are
denoted to emphasize certain areas and carry the following meanings:
Indicates a potential hazard that could result in death or injury.
Indicates a potential hazard that could result in vehicle damage.
This set-up manual is based on a vehicle of standard specification. Some minor dif-
ferences from this manual may be found in other specifications.
1
PREPARATION
WORKSHOP
#
A: Packed vehicle
B: Working space
SELF PROTECTION
#
A: Safety gear
B: Appropriate clothing
UNCRATING THE VEHICLE
For Canada only
Apply a knife to cut the carton as indicated on the car-
ton to separate it from the crate base.
A: Perforate line
Except for Canada
1. Remove the screws and cut the tie straps.
2. Remove the carton and the plastic cover.
A: Screws
B: Tie Straps
C: Carton
D: Plastic cover
The workshop where the machine is assembled
should be clean, spacious, and have a level
floor.
The operators should wear appropriate cloth-
ing, including long sleeve shirt, long pants, and
safety gear, as shown in the illustration, for
handling crates.
2
1. Remove the bolts to take off the center pole.
2. Remove the top frame first, and then vertical
frames.
A: Bolts
B: Center pole
C: Top frame
D: Vertical frame
Remove the battery electrolyte stored in the front grip.
A: Battery electrolyte container
Remove the nuts and take off the J hook of the vehicle
stopper.
A: J hook
B: Nuts
C: Washer
D: Cardboard
E: Rubber
1. Lift the vehicle with a hoist, then balance the vehi-
cle.
2. Pull the crate base forward.
3. Place the vehicle in a clean working area and
remove the hoist and hooks.
Remove the bolts carefully while holing the
center pole as it may fall. Be careful not to
scratch the ATV.
NOTE: The J hook, nuts, cardboard, washer,
and rubber are no longer needed and may be
discarded.
3
LOCATION OF PARTS
Check the components as shown.
Parts listed above are installed respectively into the position as follows.
Item Part Name Q’ty Remarks
ABattery holder 1
Flange bolt 2 6 × 16 mm
B
Trailer tow bracket 1
Flange bolt 3 10 × 30 mm
Warning label 1
Warning label (French) 1 For limited market
CBattery electrolyte
container 1
D Owner’s manual set 1
Item Part Name Q’ty Remarks
E Warning label set 1 For E-17 market
FMud guard front fender 2 Right and Left
Fastener 8
GMud guard rear fender 2 Right and Left
Fastener 6
HReflex reflector 2 For E-17 market
Flange nut 2 5 mm
I DVD 1 For E-17 market
OD : Outside diameter (mm)
ID : Inside diameter (mm)
L : Length (mm)
T : Thickness (mm)
TL
OD ID
NOTE:
The small parts of item A, B, D, E and I are in the tail box.
The parts shown as Item E, F, G, H and I in the table are supplied for limited markets.
Please hand over the parts shown as Item D and I in the table to your customer together with vehicle.
BA, C
H, G F
4
COMPONENT PARTS
Check the component parts stored in the tail box.
A: Tail box
B: Owner’s manual
Tr a i l e r t o w k i t
Warning label set (Limited market)
DVD (Limited market)
E
G
H
I
F
B
B
C
CD
D
C:
Battery holder kit
5
Before assembling the vehicle, thoroughly under-
stand the “Safety Check Out” described on
page 27.
After completion of assembly, carefully check the
vehicle referring to the “Safety Check Out”, then
deliver the vehicle to the customer.
ASSEMBLY
TRAILER TOW BRACKET
Install the trailer tow bracket.
"Trailer tow bracket mounting bolt:
60 N·m (6.0 kgf-m)
A: Trailer tow bracket
B: 10 × 30 mm flange bolt
C: Mark (UP)
Stick the warning label.
A: Warning label
B: Warning label (French) .....For limited market
REMOVING THE TAPE
Remove the tapes from the front and rear fenders.
A: Tape
UPUP
NOTE:
Install the bracket placing its UP mark faced
upward.
NOTE: (Limited market)
Stick the warning label both Aand B.
6
MUD GUARD FRONT FENDER
(FOR E-17, E-24 MARKET)
Align the mud guard front fender to the front fender.
A: Mud guard front fender
B: Front fender
Fix the mud guard front fender using fasteners.
A: Mud guard front fender
B: Fastener
NOTE:
To install the fastener, pull the center pin as C
and fix the fastener by pushing the center pin
as D.
7
MUD GUARD REAR FENDER
(FOR E-17, E-24 MARKET)
Check that the cushion is stuck to the correct position.
A: Cushion
B: Mud guard rear fender
REFLEX REFLECTOR (FOR E-17 MARKET)
Align the boss of reflex reflector to the hole of mud
guard rear fender.
Install the reflex reflector to the mud guard rear fender.
A: Mud guard rear fender
B: Reflex reflector
C: Boss
D: Hole
E: 5 mm flange nut
Align the mud guard rear fender to the rear fender.
A: Mud guard rear fender
B: Rear fender
Fix the mud guard rear fender using fasteners.
A: Mud guard rear fender
B: Fastener
NOTE:
Stick the cushion on the end of radius.
NOTE:
To install the fastener, pull the center pin as C
and fix the fastener by pushing the center pin
as D.
8
WARNING LABEL
(FOR E-17 MARKET)
Select the appropriate language label for your country.
FRONT (RIGHT)
Stick the label selected for your country.
A: Warning label (General warning)
B: Warning label (Tire information)
C: Warning label (Age 16)
D: Warning label (Gear shifting) .....For French only
E: Front fender (Right)
F: Rear fender (Right)
REAR (RIGHT)
FRONT (RIGHT)
NOTE:
Eight kind of labels: French, Finnish, Danish,
German, Spanish, Dutch, Portuguese, Swedish.
9
CHECK
#
A: Throttle cable
B: Front brake hose
C: Front brake switch lead wire
D: 2WD/4WD DIFF LOCK selection switch wiring harness
E: Rear brake lever cable
F: Rear brake switch lead wire
G: Left switch wiring harness
H: Parking brake switch lead wire
I: Horn switch lead wire (For E-17, 24 market)
J: Emergency switch lead wire (For E-17 market)
K: Starter Cable
The line drawings on page 23, 24, 25 and 26
show the proper routing of the control cables,
hose and wirings.
Refer to them in addition to following the
instructions carefully.
Indice
Altri manuali Suzuki Veicolo fuoristrada
Suzuki
Suzuki QuadRacer LT-R450 Manuale utente
Suzuki
Suzuki LT-F400 Manuale utente
Suzuki
Suzuki Vinson LT-A500F Manuale utente
Suzuki
Suzuki LT-A450X 2007 Manuale utente
Suzuki
Suzuki LTA-700 Manuale utente
Suzuki
Suzuki LT-A400 Manuale utente
Suzuki
Suzuki LT-Z50 Manuale utente
Suzuki
Suzuki kq500 Manuale utente
Suzuki
Suzuki LT-Z50 Manuale utente
Suzuki
Suzuki LT-A450X 2006 Manuale utente
Suzuki
Suzuki LT-A700X Manuale utente
Suzuki
Suzuki LT-F500F 2002 Manuale utente
Suzuki
Suzuki LT-Z90K7 2007 Manuale utente
Suzuki
Suzuki kq750 2008 Manuale utente
Suzuki
Suzuki LT-Z90K7 Guida utente
Suzuki
Suzuki LT-A750XP/Z Manuale
Suzuki
Suzuki LT-A50 Manuale utente
Suzuki
Suzuki LT-Z400 Manuale utente
Suzuki
Suzuki LT-F400 Manuale utente
Suzuki
Suzuki 2009 LT-R450 Manuale utente
