SVSi N6223 Manuale utente

N6223 NVR

USER MANUAL

• Do not operate this device in a wet environment.

• Refer servicing to qualified service personnel only.

• Please read the Operating Manual carefully before operating. Follow all operating and other instructions

carefully.

• This device should only be operated with the accompanying power adapter.

• Do not use this product near heat sources such as radiators, air ducts, areas subject to direct, intense

sunlight, or other products that produce heat.

• Do not use this product near devices that produce extreme magnetics fields.

Disclaimer

• While every effort has been made to ensure that the information contained in these instructions is

accurate and complete, no liability can be accepted for any errors or omissions. SVSi reserves the right

to change the specifications of the hardware and software described herein at any time without prior

notice.

• SVSi makes no warranties for damages resulting from corrupted or lost data due to mistaken operation

or malfunction of the SVSi hardware, software, or accessories.

IMPORTANT SAFETY INSTRUCTIONS

DO NOT DISCARD, READ BEFORE OPERATING

Please read the safety precautions carefully before

using this product. Ensure that you use the product

correctly according to the procedures described in

these instructions.

The following safety precautions are intended to

instruct you in the safe and correct operation of the

product and its accessories to prevent injuries or damage

to yourself, other persons, and property. Please read and ensure that you understand them before you

proceed to the other sections of these instructions.

Product Overview

The SVSi N6223 is a networked video recorder capable of recording up to 80 hours of high-resolution, HD

content over four Ethernet LAN connections. This rack-mount DVR is compatible with all SVSi

video-over-IP products and attaches to the video network at any point to record up to 80-hrs of 1080p

video. Each video stream is recorded and played back at its original resolution. The N6223 acts as a

receiver during recording and as a transmitter during playback. The N6223’s 3RU form-factor is stackable

for a high density of recorded video streams in a small footprint.

Installation Instructions

The NVR requires up to five connections to install.

Attach the NVR to the network by connecting up to four Ethernet cables to the RJ-45 ports on the back of

the NVR. If the application is simply using the N6223 for enhanced recording time, then only a single

network connection is required for each play/record head that will be utilized. If utilized as four NVR’s

then four network connections will be required.

Connect the power cable to the NVR and turn on the master power switch above. The unit will then power

on automatically.

1. Rack ears come pre-mounted on the NVR, which is a 3RU device.

2. Insert the NVR into the rack and align the mounting holes of the rack ears with

the holes in the rack.

3. Connect the appropriate cables as described above in Installation Instructions.

Accessing the NVR

The NVR is discoverable using our Conductor Netlite Software (found here:

http://svsiav.com/support/resources/software/), just as any other SVSi device is.

The NVR ships with Auto IP as the default IP mode for all four network cards. This means that it will

automatically configure an IP address in the range of 169.254.X.X with a netmask of 255.255.0.0. Once

Conductor discovers the four “heads” of the NVR using the Auto-Discovery tool in Conductor Netlite (or a

N-8000 series controller), you can determine the IP address of each card.

L3 NETWORK SWITCH

N6223

NVR

N-Series Encoder

DVI-I Input DVI-D Output

IR Control

232 Control

Audio Input P0 (PoE)

Power

Source

V-Output

A-Output

IR OR RS-232

Display

V-Input

A-Input

IR OR RS-232

N-Series Decoder

DVI-D OutputP0 (PoE)

Power

Audio Output

RS-232

Mounting Instructions

For rack mounting the NVR, follow the steps below:

Default username and password:

Username: admin

Password: password

Configuring the NVR

Once the NVR is discovered, double-click on of the names to bring up its settings page. On the basic

settings tab, you can assign its output and record stream numbers, change its IP configuration, enable a

dual-sync recording (N-2000 and V-Series) and enable/disable audio. You will need to complete this

process for all four DVR’s that appear in your control software.

While the four NVR heads require individual IP addresses for playback and recording purposes, overall

system management can be done by utilizing any of the four IP addresses. You can enter any one of the

NVR’s IP addresses into a web browser (or click the button with its IP address on the settings page

pictured below) to access recordings and other features covered later in this manual for all four

recording/playback heads.

On the Advanced Settings tab,

you can perform master delete

commands, reset to factory

defaults, or reboot the unit.

Recording Sources

The N6223 can record and playback 2x N-1000 stream, 8x N-2000 streams (in sync), or 40x N-3000

streams (N-3000 available late 2013) per playback/record head. Transport controls are available on the

DVR window of Netlite.

To start a recording of a source:

2. Use the drop-down menu(s) to select the desired recording head, and sources

you wish to record.

1. Select the ‘DVR’ Tab within Conductor Netlite

NOTE – if you do not enter a duration, a recording cannot begin.

Playback of Recordings

Within the Matrix view, you will notice that the NVR shows up across the top as four sources (for playback

operation) and in the left-hand column as four displays (for recording purposes).

To playback a recorded file:

3. Enter a text description of the file to be recorded. This has a maximum

character length of 255 characters. No Special Characters other than dot (.)

and dash (-) are allowed.

4. Enter duration (in minutes) for the recording to last.

5. Press the Record button.

1. Assign the output of one of the play heads to a Decoder within the Video

Matrix.

2. Click on the DVR tab of Netlite.

3. Select the appropriate DVR for playback

4. Select the file you wish to play back from the list of recordings.

5. Select the check-box at bottom if you wish to continually loop playback.

6. Use the Playback Controls to begin playback.

1. Click on the DVR tab of Netlite.

2. Select any of the DVR’s in the N6223

3. Select the file you wish to convert to MPEG from the list.

4. Click the Convert to MPEG button.*

5. The NVR will now begin converting the selected file.

Converting Files to MPEG

You have the ability to convert any non-Copy-Protected file to MPEG for offloading from the NVR.

Copy-Protected video cannot be converted from the proprietary format.

Downloading Converted MPEG Files

Enter one of the NVR’s IP addresses into your web browser. Use the default login information mentioned

at the beginning of this manual.

To convert a recorded file:

*For N-2000 or V-Series recordings, select the Convert 2nd Stream checkbox if this is a dual-stream recording and you want

both streams to be converted.

Once logged into the NVR, simply right-click and “Save As” on any file you wish to download.

Appendix

For technical support, contact support@svsiav.com or call (256) 461-7143.

Specifications

• Record up to 80-hrs of N2000 video streams 1)

• Multi-channel and Time-Shift features standard 2)

• Up to 8 recordings and 8 playbacks simultaneously for N2000 streams 3)

• Supported resolutions:

- HDTV: up to 1080p @ 60-Hz

- CG: up to 1600 x 1200 @ 60-Hz

• Stereo audio on each record channel

• Store to MPEG4 format at original resolution

• Connection: 4x – RJ-45 for network attach

• Control: Conductor NetLite, N8001, N8002, or third-party

• ~250W ~2.1A @ 120VAC

• Dimensions: 19″W x 17″L x 5.25″H

• Weight: 20-lbs

• 2-year warranty

Note: The N6123 and N6223 cannot record more than one type of stream (N1000/N2000/N3000) at

a time.

1) N1000 streams have reduced recording times due to larger bandwidths and N3000 streams would

have increased recording times due to larger bandwidths relative to N2000 streams.

2) Time-shift (tape delay) feature not available for N1000 recordings.

3) N1000 multi-channel stream count is reduced and N3000 multi-channel steam count increased based

on stream bandwidth. All streams must be synchronous.

ITSIMPLYWORKS

SVSi and voLANte are trademarks of Southern Vision Systems, Inc. in the United States and other countries.

800DOCN6223MNREV1.1

Made in the U.S.A

360B Quality Circle Suite 200, Huntsville, AL 35806 • 256.461.7143 • www.svsiav.com

Indice

Altri manuali SVSi Registratore digitale

SVSi

SVSi N6123 Manuale utente

Manuali Registratore digitale popolari di altre marche

FLIR

FLIR M3100E Series Manuale utente

VTRACKPRO

VTRACKPRO FPRO300 Manuale utente

Swann

Swann NVR-7085 models Manuale utente

XtendLan

XtendLan DVR-1670C Manuale utente

urmet domus

urmet domus 1093/004AHD Manuale utente

Holux

Holux M1 Manuale utente

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuale utente

Whistler

Whistler D16VRS Manuale utente

Defender Security

Defender Security 82-20235 Manuale utente

MISUMI

MISUMI MP-WF100M Manuale utente

Speco

Speco D8HU Manuale utente

UST

UST DDR-E04AA Istruzioni per l’uso

Consolidated

Consolidated Digital Video Recorder Manuale utente

Mace

Mace DVR0404RW Guida rapida

RCA

RCA RTD315W Manuale utente

FSM

FSM Colibri Grande PRO Manuale utente

Hauppauge

Hauppauge HD PVR 2 Manuale utente

Identivision

Identivision ICR-PH161i PIONEER Manuale utente