Swann SW248-LM8 Manuale utente
SW248-LM8-10006-170309
8” LCD Monitor
Instruction Manual
SW248-LM8
FCC WARNING STATEMENT
NOTE: This equipment has been tested and found to comply with the limits for
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important Notice
All jurisdictions have specific laws and regulations regarding the use of
monitoring & recording devices. Before using any camera for any purpose, it
is the buyer’s responsibility to be aware of all applicable laws and regulations
that prohibit or limit the use of cameras and to comply with the applicable laws
and regulations. The legality of watching people other than you changes from
country to country and even state to state. Contact your local government’s
privacy information body or your local Police for more information on what if
any restrictions you may face.
WARNING: Important notice about correct usage of the power adapter
The correct orientation for the enclosed power adapter is in a vertical or floor
mount position.
Precautions and Safety Instructions
•Read this manual carefully before using the Monitor
•Follow the instructions for proper and safe use of this product
•Keep the instructions in a safe place for future reference
•Use only the power adapter that is designed and supplied with this
product
•Do not use this device near water or other liquids
•Do not use solvents or alcohols to clean the unit, use a dry soft cloth,
or moisten cloth with diluted dish detergent only
•Ensure the vents on the sides and back of the unit are not covered
•Do not use near heat sources such as heaters, stoves, fireplaces
•If the product has been damaged do not attempt to repair it yourself -
contact Swann Technical Support for assistance
-i-
Table of Contents
1. Before You Begin 1
2. Package Contents 2
3. Monitor Layout 3
4. Monitor Controls 4
5. Remote Control Layout 5
6. Monitor Connections 6
6.1 Connecting the Power Adapter
6.2 Connecting the AV Cable
7. Menu Operations 7
7.1 Picture Menu
7.2 Option Menu
7.3 Clock Menu
7.4 System Menu
8. Troubleshooting Guide 9
9. Technical Specifications 10
Warranty 11
Swann Technical Support 12
-ii-
1. Before You Begin
Storage
1. Keep this product away from extreme hot or cold places. The
storage temperature ranges from -20 to 60 and the
operating temperature is from 0 to 40
2. Do not use this product in or near moist environments such as
bathtubs, wash basins, kitchens, basements, swimming pools etc.
3. Do not expose the LCD display to high humidity, dust, oil or smoke
4. Do not throw or drop this product
5. Do not subject this device to strong vibrations, shock
6. Do not brush or scrub this product with abrasive objects
Maintenance
1. Disconnect all cables from the monitor before cleaning
2. Wipe the enclosure, screen and keys using a dry soft cloth, or
moisten cloth with diluted dish detergent only
3. Do not use polishing cloth, abstergent, or other types of chemical
detergents with alcohol or benzene
Warning!
1. Do not use this device while driving
2. Do not submerge this product in liquids or expose to rain
Special
Notice
•Do not attempt to repair or disassemble, there are no user
serviceable parts inside this device.
•Contact Swann Technical support if this monitor
malfunctions or fails to operate correctly
-1-
2. Package Contents
•LCD Monitor
•Car Power Adapter
•Power Adapter
•Remote Control
•AAABatteries for Remote Control
•A/V Cable
•Monitor Stand
•Instruction Manual
If any of the above accessories are damaged or missing, contact
Swann Communications for assistance.
-2-
3. Monitor Layout
1. LCD Screen
2. AV1/AV2 Button
3. AUTO Button
4. PICT Button
5. MENU Button
6. POWER Button
7. UP Button
8. DOWN Button
9. VOL+ / Right
Button
10. VOL- / Left Button
11. IR Remote Sensor
12. Monitor Stand
13. Bracket
14. AV2 in jack
15. AV1 in jack
16. Headphone jack
17. DC Input
18. Speaker
-3-
4. Monitor Controls
•AV1/AV2: Switches input from AV1 to AV2
•AUTO: Press to cycle between AV1 and AV2
inputs at 4, 6 or 8 seconds – push again to turn
off
•
•PICT: Choose from 5 image settings: Standard,
Soft, Vivid, Light and Personal
•
•MENU: Press to enter or exit the menu
•POWER: Press to turn monitor on/off
•▲: Move selection up in Menu
•▼: Move selection down in Menu
•VOL+: Increase Monitor volume or move
right in menu
•VOL-: Decrease the Monitor volume or
move left in the menu
-4-
5. Remote Control Layout
POWER: Turn the monitor on/off
MUTE: Press to disable sound, press MUTE
again or press VOL to enable sound
▲: Move selection up
▼: Move selection down
◄/VOL-: Decrease volume / move left
►/VOL+: Increase volume / move right
MENU: Press to enter / exit the Menu
MODE: Change image settings from Standard,
Soft, Vivid, Light and Personal
CALL: Displays current AV channel
TIMER: Push to set Sleep Timer up 120 minutes
LANG: Sets the menu language (default English)
CALE: Press to set Calendar – date appears in Year – Month – Day
format. Use ▲▼ to change year and ◄► to change day
AV: Press to switch between AV1 and AV2
Press to flip image horizontally
Press to flip image vertically
-5-
6. Monitor Connections
6.1 Connecting the Power Adapter:
Connect the Power Adapter plug
to the input on the side of the
monitor marked DC 12V. Plug the
other end of the adapter to a power
point or cigarette lighter if applicable
6.2 Connecting the AV Cable:
AV conversion cable
Insert the mini-jack end of the AV
Cable into the AV1 or AV2 port on
the Monitor. Connect the Yellow
RCA cable to the video source of
the AV device. Connect the Red
and White RCA cables to the Right
and Left audio source if applicable
-6-
7. Menu Operation
Press MENU to display following options:
PICTURE OPTION CLOCK
SYSTEM PRESET
7.1 PICTURE – CONTRAST, BRIGHT, COLOR, SHARP, TINT
Press or to select the item and press ◄or ►to adjust the value
Notice
The TINT option will appear on NTSC Monitors only
7.2 OPTION – LANGUAGE, CALENDAR, GAME
LANGUAGE, CALENDAR and GAME displays on the screenas below
description:
7.2.1 LANGUAGE
Press or to select Language and press ◄or ►to change on
screen languages
7.2.2 CALENDAR
Press or to highlight Calendar and press ◄or ►to adjust
Press or to change year and press ◄or ►to change month
7.2.3 GAME – Push to enter Game Mode
-7-
Altri manuali per SW248-LM8
2
Indice
Altri manuali Swann Monitor
Swann
Swann SW244-LMP Manuale utente
Swann
Swann DP885C Manuale di istruzioni
Swann
Swann SW248-LM8 Manuale utente
Swann
Swann SW248-LM8 Manuale utente
Swann
Swann AMI Turbitrack Manuale utente
Swann
Swann SW248-8LM Manuale utente
Swann
Swann AMI Solicon4 Manuale utente
Swann
Swann AMI Oxytrace Manuale utente
Swann
Swann SW248-8LM Manuale utente
Swann
Swann SW346-7MC Manuale utente
