SWARCO Caiman Manuale utente
SWARCO
CAIMAN
Junction Box Installation
CAIMAN
WIDE BEAM STOP+MOTION
RADAR DETECTOR
Caiman_JunctionBox-Installation_BE_00
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
2/20
CONTENT
1Detector Type CAIMAN (1st Generation)...................................................................................... 3
1.1 Identifying System Components..............................................................................................3
1.2 Connecting Cable and Junction Box .......................................................................................5
1.2.1 Removing the cable shielding/Preparing the braid..........................................................5
1.2.2 Removing unnecessary wires..........................................................................................6
1.2.3 Connecting Cable and Junction Box ...............................................................................6
1.2.4 Removing the insulation of the wires...............................................................................6
1.2.5 Connecting the wires to the terminal block......................................................................7
1.2.6 Connected Junction Box.................................................................................................. 8
1.3 Placing the Gasket ..................................................................................................................8
1.4 Connecting Junction Box and CAIMAN................................................................................... 9
1.5 Attaching the Sensor to the Bracket......................................................................................10
1.6 Attaching the Sensor to the Pole...........................................................................................10
2Detector Type CAIMAN-PLUS ....................................................................................................11
2.1 Identifying System Components............................................................................................11
2.2 Connecting Cable and Junction Box .....................................................................................13
2.2.1 Removing the cable shielding/Preparing the braid........................................................13
2.2.2 Removing unnecessary wires........................................................................................14
2.2.3 Removing the insulation of the wires.............................................................................14
2.2.4 Connecting the wires to the terminal block....................................................................15
2.3 Placing the Gasket ................................................................................................................16
2.4 Connecting Junction Box and CAIMAN-PLUS......................................................................17
2.5 Attaching the Sensor to the Bracket......................................................................................18
2.6 Attaching the Sensor to the Pole...........................................................................................18
3Detector Type CAIMAN-PRO......................................................................................................19
4Important Legal Disclaimer Notice ............................................................................................20
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
3/20
1 Detector Type CAIMAN (1st Generation)
1.1 Identifying System Components
Figure 1: e.g. CAIMAN M36 front Figure 2: e.g. CAIMAN M36 back
Figure 3: e.g. BFW_Caiman_36S Figure 4: Screws M3x8; eight screws required
Figure 5: Gasket
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
4/20
Figure 6: RD_Caiman_JB_3070 / RD_Caiman_JB_36
Figure 7: Female blade terminal (6.3mm)
Figure 8: Blade pin (6.3mm)
Figure 9: Cable; Lapp cable UNITRONIC BUS IBS Yv COMBI type 2170217 recommended
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
5/20
1.2 Connecting Cable and Junction Box
1.2.1 Removing the cable shielding/Preparing the braid
1.2.1.1 Removing the shielding
Figure 10: Cable with removed shielding
Figure 11: Cable with removed braid; step not required if braid shall be connected to the Junction Box
1.2.1.2 Preparing the braid
If the braid of the homerun cable shall be connected to the Junction Box please follow the
following steps:
Figure 12: The braid of the homerun cable is not cut off but twisted instead
Figure 13: A female blade terminal 6.3mm is crimped onto the twisted braid
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
6/20
1.2.2 Removing unnecessary wires
Figure 14: Cable without unnecessary wires. Only wires given in Table 1 are needed
Pin No.
Function
Wire Color
(Lapp type 2170217)
1
CAN H
green
2
CAN L
yellow
3
RS485 H
gray
4
RS485 L
pink
5
Power +
red
6
Power -
blue
Table 1: Pinout of terminal block connector
1.2.3 Connecting Cable and Junction Box
Figure 15: Cable connected to the junction box with tightened connector and tightened cord grip
1.2.4 Removing the insulation of the wires
Figure 16: Wire with removed insulation
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
7/20
1.2.5 Connecting the wires to the terminal block
Figure 17: Usage of the screw driver to insert a wire into the terminal
Figure 18: Usage of the screw driver to insert a wire into the terminal
Figure 19: Routing of the cable wires inside the junction box
Figure 20: For the connection of the braid a blade pin 6.3mm is attached to the junction box
Figure 21: Blade terminal connected to the blade pin
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
8/20
1.2.6 Connected Junction Box
Figure 22: Wires connected to the Junction Box according to Table 1
Figure 23: Wires connected to the Junction Box including connected braid
1.3 Placing the Gasket
Figure 24: Junction Box with gasket placed inside the prepared slot
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
9/20
1.4 Connecting Junction Box and CAIMAN
Figure 25: Placement of the Junction Box relative to the CAIMAN
Figure 26: Junction box attached to the CAIMAN
Screw each corner of the JBox onto
the sensor.
Arrows on the figure indicate where
the screws should go.
Note: the arrow indicating the top of
the sensor shall point in the same
direction as the arrow indicating the
top of the JBox. The arrow on the
figure shows where the indication
can be found at the sensor.
Attention: After the sensor connector
is attached to the JBOX, do not
further turn or twist the JBOX as this
may damage the connector, until all
the screws are securely tightened.
www.swarco.com
SWARCO TRAFFIC SYSTEMS GMBH, Niederkircher Straße 16, D-54294 Trier, Germany
T. +49-651-21002-0, +49-651-21002-999, E. detection@swarco.de
10/20
1.5 Attaching the Sensor to the Bracket
Figure 27: Sensor attached to the bracket side
Figure 28: Sensor attached to the bracket back
1.6 Attaching the Sensor to the Pole
Figure 29: Sensor attached to the pole
Screw each corner of sensor onto
the bracket, with the back of the
sensor looking into the bracket.
Arrows on the figure indicate where
the screws should go.
The sensor is fixed to the bracket
with the cable looking downwards.
The sensor is fixed to the pole with the cable looking downwards.
Indice
Altri manuali SWARCO Sensore di sicurezza
