SWEEX MO200 Manuale utente

English version

TABLE OF CONTENTS

Specifications 6

The splitter 7

Connecting the Sweex ADSL 2 Modem 7

Configuring the computer to connect to the modem 8

Internet browser settings for Windows 98SE, 2000 and XP 11

Modem access (Login) 11

Setting the Internet Provider (ISP) 13

Opening ports in the modem (Port Forwarding and DMZ) 14

LAN settings 15

Changing the password (User Management) 16

Remote modem management (Web Access Control) 17

Upgrading the firmware of the modem (update firmware) 17

Resetting the Modem to its factory settings 18

List of Internet Providers and corresponding subscriptions 19

Warranty 23

GNU/GPL 23

English version

MO200/MO200UK Sweex ADSL 2/2+ Modem/Router Annex A

Introduction

First of all, many thanks for purchasing the Sweex ADSL 2/2+ Modem/Router Annex A. The Sweex ADSL 2/2+ Modem/Router Annex A enables

you to share a fast ADSL 2 Internet connection and to set up your own network.

To ensure this product operates correctly, we advise you to carefully read this manual first. If despite this manual you still experience problems during

installation or operation of this product, go to www.sweex.com and look under the heading service & support.

In order to fully enjoy the Sweex ADSL 2/2+ Modem/Router Annex A, it is important to observe the following:

• Do not expose the Sweex ADSL 2/2+ Modem/Router Annex A to extreme temperatures. Do not place the device in direct sunlight or in the

direct vicinity of heating elements.

• Do not use the Sweex ADSL 2/2+ Modem/Router Annex A in extremely dusty or moist surroundings.

• Protect the device against powerful shocks or jolts – they may damage the internal electronics.

• Never attempt to open the device yourself – it will cause the warranty to lapse.

Contents of the box

Prior to using the Sweex ADSL 2/2+ Modem/Router Annex A, check if all required parts are present. The following parts must be present in the box:

• ADSL 2/2+ Modem/Router

• Power supply adaptor

• RJ-45 UTP Ethernet network cable (length 170 cm)

• RJ11 telephone cable (length 185 cm)

• CD-ROM with manual and Panda antivirus trial software

If one of the above parts is missing, please contact the retail outlet where you purchased the device.

English version

Specifications

• Suitable for ADSL via an analogue telephone line (Annex-A)

• Supports: ADSL, ADSL 2 and ADSL 2+

• 4 x RJ-45 UTP ports, 10/100 Mbps IEEE 802.3x standard

• RJ11 ADSL port

• Download speed: 24Mbps, Upload speed: 1Mbps

• Built-in Firewall and Port Forwarding

• Supports: Windows 98SE, 2000 and XP

Additional specifications

• Full rate ANSI T1.413 Issue2, ITU-T G.992.1 and ITU-T G.992.2, ITU G.992.3, ITU G.992.5 and READSL2 ADSL2/2+ standards compliant

• Supports Annex M and Annex L

• Supports Encapsulation: PPPoA, PPPoE, Bridged, Routed, Static, DHCP

• Supports VPN pass through

• Web-based configuration and Remote Access configuration

Front or top view of the modem

LED Indicators Status Meaning

PWR Lit Indicates that the modem is switched on

1-4 Lit Indicates that a computer is connected to the relevant port

1-4 Blinking Indicates activity between the relevant computer and the modem

ADSL Lit The connection with the ADSL line is ok

ADSL Regular blinking The modem is busy setting up a proper connection or no ADSL is connected

to the RJ11 port

ADSL Lit and blinking fast Indicates activity between the computer (1-4) computer and the Internet

PPP Lit Indicates the use of a PPP connection

English version

Rear view of the modem

Starting on the left, the following connections can be found at the rear of the modem:

• ADSL port for connecting the ADSL line with telephone cable RJ11.

• UTP Ethernet ports 1, 2, 3 and 4 for connecting computers with an Ethernet network cable RJ45.

• Power port for connecting the power adaptor.

Side view

The Reset button is located on the side of the modem. Use a thin item to press the button. Press and hold the button for 15 seconds. Note! After

this, all settings which apply to your connection and network need to be reconfigured.

The splitter

In order to separate the ADSL signal from the normal telephone signal, you need to use a splitter. This enables you to simultaneously make calls and

surf the Internet using the same telephone line. The signal comes from the wall socket or the meter cupboard and enters the splitter. Two telephone

cables are connected to the output of the splitter. One leads to the modem and the other to the telephone.

Note! The ADSL modem does not include a splitter. It can be obtained from various DIY stores.

Connecting the Sweex ADSL 2 Modem

1. Connect the power adaptor (included) to the rear of the modem and the mains socket. The LED under PWR is lit. In the event the LED is not lit,

check the connections of the power adaptor to the ADSL modem and the mains socket.

2. Connect the telephone cable (RJ11) carrying the ADSL signal to the ADSL port at the rear of the modem. The LED under ADSL will now start

to blink. After approximately 30 seconds the LED will be lit continuously. In the event the LED is not lit, check whether the splitter is properly

connected and/or whether the ADSL line is ok.

3. Switch on the computer and connect it to the rear of the modem using a network cable (UTP RJ45). You can select any of the ports 1, 2, 3 and 4.

The corresponding LED at the front of the modem will be lit. In the event the LED fails to light up, check whether the network cable is properly

connected to the computer and the modem.

English version

Configuring the computer to connect to the modem

Windows XP

Go to “Start” (Start) “Control Panel” (Control Panel). Then go to “Network and Internet Connections” (Network and Internet Connections).

Open “Network Connections” (Network Connections).

Or, if the Windows classic style is used:

“Start” (Start) Settings “Network Connections” (Network Connections).

Right-click “LAN Connection” (LAN Connection) and select “Properties” (Properties). The following screen appears:

Under the tab “General (General) select TCP/IP and click “Properties” (Properties).

Select the options “Obtain an IP address automatically“ (Obtain an IP address automatically) and “Obtain DNS server address automatically”

(Obtain DNS server address automatically).

Confirm the settings by clicking “OK” (OK). The network settings for Windows XP have now been configured correctly. The correct settings for the

Internet browser will be discussed later in this manual.

English version

Windows 2000

Go to “Start” (Start) “Control Panel” (Control Panel). Then go to “Network and Internet Connections” (Network and Internet Connections).

Open “Network Connections” (Network Connections).

Or, if the Windows classic style is used:

“Start” (Start) Settings Open “Network Connections” (Network Connections).

Right-click “LAN Connection” (LAN Connection) and select “Properties” (Properties). The following screen appears.

Now select “Internet Protocol (TCP/IP)” and click “Properties” (Properties).

Select the options “Obtain an IP address automatically” (Obtain an IP address automatically) and “Obtain DNS server address automatically”

(Obtain DNS server address automatically). Click “OK” (OK) twice.

The network settings for Windows 2000 have now been configured correctly. The correct settings for the Internet browser will be discussed later

in this manual.

English version

Windows 98SE

Go to “Start” (Start), “Setting” (Settings), “Control Panel” (Control Panel) and click “Network” (Network).

Under the tab “Configurartion” (Configuration), select the line “TCP/IP ” which corresponds with your network card and click

“Properties” (Properties).

Under the tab “IP Address” (IP Address), select the option “Obtain an IP address automatically” (Obtain an IP address automatically).

Under the tab “Gateway”, the list of “Installed gateways” (Installed gateways) must be empty. If so required, select each gateway and click

“Remove” (Remove).

English version

Under the tab “DNS Configuration”, select the option “Disable DNS” (Disable DNS). Click “OK” (OK) twice.

The network settings for Windows 98SE have now been configured correctly. The correct settings for the Internet browser will be discussed below.

Internet browser settings for Windows 98SE, 2000 and XP

1. In order to properly access the modem, the browser settings must be correct. This is easy to check by starting up Internet Explorer and selecting

“Tools” (Tools) from the menu bar and then selecting the option “Internet Options” (Internet Options).

2. In this window, go to “Connections” (Connections) and select “Never dial a connection” (Never dial a connection) or remove all connections

listed in the field above.

3. At the bottom, click “LAN Settings” (LAN Settings), remove all ticks and click “OK” (OK).

4. Restart the computer.

Modem access (Login)

Open your web browser. In this example we use ‘Internet Explorer’.

The standard modem IP address is: 192.168.200.1. An IP address is a unique number required by each network device, including a computer

or modem, in order to be active within that network. Without an IP address you are unable to make connections within a network.

Type the modem IP address 192.168.200.1 in the browser address bar. You can now access the modem.

English version

The modem login screen appears. Fill out the login name and the corresponding password. The standard login is “sweex” and the corresponding

password is “mysweex”.

If this login screen fails to appear, recheck the settings of your Internet browser as described above. Also check the IP address of your computer.

In this IP address, only the digits after the last dot may deviate from the IP address of the modem (e.g.: 192.168.200.xxx). Do this as follows:

Win2000/WinXP: Click “Start” (Start) - “Run” (Run)- Type cmd - press ENTER- In the black window type ipconfig - press ENTER and your IP

address is displayed.

Win98/Me: Click “Start” (Start) - “Run” (Run) - Type winipcfg - press ENTER. In the window, select your network adaptor. (Usually NOT the

ppp adaptor) and your IP address is displayed.

Once logged in, the main screen of the modem appears.

This screen displays the current Internet connection and a variety of system information.

English version

Setting the Internet Provider (ISP)

In order to facilitate the installation process, the Sweex ADSL 2/2+ Modem/Router Annex A disposes of a pre-programmed list of

provider settings.

To this end, go to the “Setup Wizard”. The following screen appears:

Under “Country” select the appropriate country and under “ISP”, select the corresponding Internet Provider. The modem will now automatically

complete the settings. Then click “Next”. After this, some Internet providers require a user name and password to be filled out. Check this with the

list of providers further down in this manual or with the details you received from your Internet provider. Alternatively, contact your Internet provider.

Click “Apply” to store and activate the settings.