Swinnus CTR-S200 Manuale utente
CTR-S200
User Guide
2021.12.02
- Contents -
1. Product composition ····································································· 1p
2. Specification ····················································································· 2p
3. Part name & function description ············································· 3p
4. Installation process ········································································· 4p
5. Event ·································································································· 4p
- 3 -
1. Product composition
[CTR-S200]
[Harness Cable]
[Cable Grand]
- 4 -
2. Specification
Classification
Detail
Model
CTR-S200
Operating System
Firmware
Mobile
Communucation
FCC
LTE Band 5 : 824 MHz - 849 MHz
LTE Band 7 : 2 500 MHz – 2 570 MHz
WCDMA Band 2 : 1 850 MHz – 1 910 MHz
WCDMA Band 4 : 1 710 MHz – 1 755 MHz
WCDMA Band 5 : 824 MHz - 849 MHz
BT 5.0 : 2 402 MHz – 2 480 MHz
CE
WCDMA Band 1 : 1 920 MHz - 1 980 MHz (25dBm)
WCDMA Band 8 : 880 MHz - 915 MHz (25dBm)
LTE Band 1 : 1 920 MHz - 1 980 MHz (25dBm)
LTE Band 3 : 1 710 MHz - 1 785 MHz (25dBm)
LTE Band 5 : 824 MHz - 849 MHz (25dBm)
LTE Band 8 : 880 MHz - 915 MHz (25dBm)
BT 5.0 : 2 402 MHz – 2 480 MHz (-7.32dBm)
Bluetooth
BLE 5.0
Location Information
GPS
Weight
310g(Including a battery)
Notification
LED(GPS, Stauts, Power)
Battery
Lithium-Ion Battery / 6,000mAh
Operating Voltage(V)
3.7V ~ 4.2V
Input Voltage(V)
AC24V
Dimension(mm)
90(W) X 150(L) X 29(D)
- 5 -
3. Part name & function description
Part name
Explanation
Features
[1] GPS LED (Blue)
Reception status for
GPS Signal
· If LED is turned on, GPS module is being
attempted
· If LED blinks, GPS module is successfully
recepted signal
[2] Status LED (Green)
Communication status for
Reefer container, mobile network
· If LED blinks briefly, IoT device is failed to
communicated with reefer container
· If LED is turned on for a long time, IoT device
is communicating with mobile network
[3] Power LED (Red)
Display the power status
· If LED is turned on, IoT deevice is operating
· If LED is turned off, IoT device is on sleep
mode(or power off)
[4] ON/OFF Toggle Switch
Device Power ON/OFF
· Put ON/OFF Toggle Switch to operate IoT
device on initial installment
[5] Harness Cable
controller cable connector
· Cable connector for connecting reefer cotnainer
controller & IoT device physically
- 6 -
4. Installation process
(1) Drill a hole in the location where the equipment is installed outside the controller panel
(2) Connect the RS232 cable inside of the control box to the RS232 connector of the main
body
(3) Connect the AC 24V power line inside the reefer container control box to the AC
24V connector of the main body
(4) Check the status of the POWER LED on
(5) Turn [4]ON/OFF Toggle Switch on to operate IoT device
(6) Once the IoT device is attached on the drilled part, the installation is completed.
5. Event
(1) Shock Event
: In normal state, real-time shock is detected (shock outside the threshold) and event
packet is generated
※ Shock packets are not duplicated in one cycle
(2) Equipment detachment detection even
: It detects the detachment status of the equipment in real time and generates an event
packet
※ Desorption packets are not duplicated in one cycle
※ CE Compliance Information
Hereby, SWINUUS declares that this product is in compliance with the essential
requirements
and other relevant provisions of RE Directive 2014/53/EU.
Instructions for use included in this manual are also available on the
website(http://www.swinnus.com)in multiple languages.
country of sale : UK / DE
※ This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
- 7 -
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS
NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference, including interference that may cause
undesired operation of the device.
The user manual for an intentional or unintentional radiator shall caution the user
that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
Indice
Altri manuali Swinnus Serratura
