Swisscom Powerline Guida utente
1Deutsch
Powerline
Connection Kit setup
2 English
Connecting two Powerline adapters
1
Plug the Powerline adapter directly
into the wall power socket.
2
Plug the first Powerline adapter
to your DSL router using the
provided Ethernet cable.
«» and « » light up in green.
(It is possible that the LEDs blink. This is not an error.)
3
Plug the second Powerline adapter
to your computer or your TV-Box.
«», « » and « » light up in
green.
(If the computer or the TV-Box are not switched on,
«» is not lit. It is possible that the LEDs blink. This is
not an error.)
3English
Ethernet connection
Everything is in order
Problem detected > Check that the cables are securely
connected to the corresponding Powerline adapter.
Powerline connection
Excellent connection
Good connection
Low connection > Always connect the Powerline
adapter directly to the wall electrical socket. If your
wall electrical socket allows for multiple devices to
be plugged in, make sure that the Powerline adapter
is the only device plugged in.
no connection
Power
Power on
Energy saving mode > The Powerline adapters
automatically switch off 15 minutes after the
connected devices are powered off .
Out of service
Reset Button
With this button you can reset your Powerline adapter to its initial
state. In order to do this, press the button for ca. two seconds and
release. All LEDs light up briefly in orange.
Pairing Button
This button allows you to add additional Powerline adapters to your
existing Powerline network.
Displays (LED) and buttons
English
4 English
Additional Powerline adapters
You can connect additional Powerline adapters (optional). In order to do so, your existing Pow-
erline adapters must be on. If one of them is in energy saving mode, unplug it and replug it
again. Wait until the green light turns on.
1Plug the Powerline adapter into a power socket at the desired location.
2Press approx. 15 seconds the Pairing button of your new Powerline adapter, until all
LEDs (« », « » und « ») light up in orange.
After a short while the LED indicating that your new adapter is in
service « » will light up in green.
3Press approx. half a second the Pairing button of one of your already existing Powerline
adapters.
The service LED « » will start blinking in green.
Note: if it’s not blinking, repeat this step.
4Press approx. half a second the Pairing button of your new Powerline adapter.
The service LED « » will start blinking in green.
After a few seconds « » and « » light up in green.
Note: if it’s not blinking, repeat this step.
5Connect the Ethernet cable included in the package to your device.
(« », « » and « » light up in green. If the device is not on, « » does not light up.)
Note: you can connect additional Powerline adapters from Swisscom by proceeding exactly
this way.
Press half a second then releaseNew
adapter
Press half a second then release1st or 2nd
adapter
Press until all LEDs light upNew
adapter
5English
Important safety instructions
It is important to read and understand the following safety instructions before operating
the Powerline adapter.
> Do not exceed a 2250 Watt load on the adapter.
> The Powerline adapter should only be used in a dry place.
> Do not use the Powerline adapter in bathrooms.
> The Powerline adapter must not be opened by unqualified personnel.
> Do not try to repair the Powerline adapter yourself. You risk being electrocuted!
> Under no circumstances should the Powerline adapter come into contact with water or
other liquids.
> Always use the supplied Ethernet cable to connect the Powerline adapter.
> Do not insert any objects into the openings of the Powerline adapter.
> To shut it off, unplug it from the socket.
> Do not expose the Powerline adapter to direct sunlight.
> Slots and openings on the housing are used for ventilation and must not be blocked or
covered.
> The Powerline adapter must not be set up next to a radiator.
> The Powerline adapter should only be used in places where there is adequate ventilation.
> Before cleaning the housing, disconnect the Powerline adapter from the mains. Never use
water, thinner, benzene, alcohol or other strong detergents to clean the Powerline adapter
as this may damage the housing. Use only a slightly damp cloth.
> In the event of damage, disconnect the Powerline Adapter from the mains and return the
Powerline adapter to the following address:
Swisscom (Switzerland) Ltd
Materialrücknahme
Postfach
4552 Derendingen
> The following situations constitute damage:
> if the power cable or plug is damaged.
> if liquid is spilled on the Powerline adapter.
> if an object gets inside the Powerline adapter.
> if the Powerline adapter is exposed to rain or water.
> if the Powerline adapter does not work.
> if the Powerline adapter housing is damaged.
Swisscom (Schweiz) AG
Contact Center
CH-3050 Bern
www.swisscom.ch
Powerline-Netzwerk über bestehendes Stromnetz
Réseau Powerline par le réseau électrique existant
Rete Powerline tramite la rete elettrica esistente
Powerline network through existing electrical network
DSL-Router/Routeur
SAPXXX 03/2011
SAP10042117 03/2011
Indice
