Swisson XND-4 Manuale utente

XND-4

4-Port Ethernet DMX Node

User Manual

UM_XND-4-D0-LEN-V01-00.DOCX 2016-07-05

 
 
3 
Index 
Index ..........................................................................................................................................................................3 
Introduction................................................................................................................................................................4 
Unpacking...................................................................................................................................................................4 
Safety Information ......................................................................................................................................................5 
Device Overview .........................................................................................................................................................7 
Settings and Menu......................................................................................................................................................8 
Ethernet Port Status Information ..............................................................................................................................15 
Status LEDs ...............................................................................................................................................................15 
Screen Saver .............................................................................................................................................................16 
Firmware Updates ....................................................................................................................................................16 
Technical Data ..........................................................................................................................................................17 
Ordering Information................................................................................................................................................18 
Credits ......................................................................................................................................................................18 

Introduction

XND-4 is a user friendly Art-Net to DMX converter supporting the distribution of four universes of DMX via four

individually optically isolated DMX outputs. Since most major lighting consoles are capable of transmitting Art-Net

data, XND-4 is all you need in order to take advantage of your console’s networking capability, allowing you to

transmit a vast number of universes over one single network cable. In some cases, users may profit from already

existing networking infrastructure.

Further, the XND-4 is also perfectly suited to send DMX data to your fixtures from a computer or even from a mobile

device. Many light controller programs for PC or Mac support Art-Net output natively and with the help of XND-4’s

DHCP capability, you can even let your workplace network infrastructure do the network configuration of your XND-

4 automatically for you.

With its 128x64 pixels OLED display however, configuring the network and setting up your Art-Net preferences

manually is no trouble at all and helpful status information is always at hand.

Applications

Concert lighting

Live events

Multimedia shows

Theaters

TV studios

Theme parks

Architectural lighting

Typical Application

Unpacking

The XND-4 is packaged in a cardboard box. The following items are included:

The device.

This user manual.

Safety Information

It is essential that you read and understand this manual before operating the device and that you

follow the instructions given below closely when you set up, connect and use the XND-4. Do not

use the device in any way or for any purpose not described in this user manual.

This product is approved for professional use only; it is not intended for household usage. Pay

attention to all warnings given in this manual and use this device only in accordance with

applicable laws and regulations.

Safety Precautions

Disconnect the device from the AC power supply before removing any cover or part,

including fuses, even when not in use.

Ensure that the device is electrically connected to ground (earth).

Use only a source of AC power supply that complies with local building and electrical

regulations and which has both overload and ground-fault (earth fault) protection.

Before using the device, check that the power distribution equipment and cables are in

perfect condition and rated for the current required by all connected devices.

Isolate the device from power supply immediately if the power cable or the power plugs

are in any way damaged, defective or wet, or if they show signs of overheating.

Do not expose the device to rain or moisture.

Do not operate the device if any cover or component is missing, damaged or deformed.

Refer any service operation not described in this manual to Swisson.

Provide unrestricted airflow around the device.

Do not operate the device if the ambient temperature exceeds 55°C (131°F).

Do not modify the device in any way not described in this manual or install other than

genuine Swisson parts.

Do not attempt to bypass any fuse. Replace any defective fuse with one of the specified

type and rating only.

When suspending the device, ensure that the supporting structure and all hardware used

can hold at least 10 times the weight of all devices suspended together.

When suspending the device, install a secondary attachment such as a safety cable that is

approved by an official body such as, e.g. TÜV (German Technical Monitoring Association),

a safety attachment for the total weight it secures. The safety cable must comply with EN

60598-2-17 section 17.6.6 and be capable of bearing a static suspended load 10 times the

weight of the device.

Make sure that any external cover and rigging hardware is securely fastened.

Provide an adequate clearance underneath the work area and a stable platform whenever

installing, servicing or moving an overhead device.

Do not use the device in areas where it is exposed to direct sunlight.

Do not use the device in areas that are considered to be “highly inflammable”.

Device Overview

1. OLED display.

2. Encoder wheel / [OK] button. The encoder is primarily used for selecting menu items by turning the knob. It

also functions as a push button. This manual refers to this button simply as [OK] button or [OK].

3. [Cancel] button.

4. Ethernet port button [E].

5. Ethernet port (RJ45 Neutrik etherCON socket).

6. Output port buttons [1] –[4]. These push buttons are used to change to which universe the respective output

is connected. An output port status LED showing status information is located directly below each of those

buttons.

7. Signal output ports 1 –4.

8. Neutrik powerCON input socket.

9. Neutrik powerCON output socket.

10. USB type-B socket for firmware updates.

Mains Connection

The user must supply a suitable power cable. He may then either hard-wire the power cable to the building’s electrical

installation, providing an easily accessible power on/off switch close to the device, or install on the power cable a

grounding-type (earthed) mains plug that is suitable for the local power outlets, following the power plug

manufacturer’s instructions. Consult a qualified electrician, if you have any doubts about the proper installation.

A blue Neutrik powerCON NAC3FCA cable mount connector must be used to supply power at the XND-4’s power input

socket.

Warning! For protection against dangerous electrical shocks, the device must be grounded (earthed). The

local AC power source must be supplied with both overload and ground-fault (earth fault) protection.

Important! Only attach or remove a Neutrik powerCON connector while it is connected to the mains to

apply or cut power in an emergency situation, as by doing so may cause arcing at the terminals that will

damage the connectors.

Power Outlet

Warning! The total current load of all devices connected to the AC mains power outlet of the XND-4 must

not exceed 19.8 amperes.

• A power cable that meets the requirements specified in the safety instructions section of this manual must be used

to connect the XND-4 to AC mains power and to connect other devices to the power outlet.

• A light-grey Neutrik powerCON NAC3FCB cable-mount connector must be used to draw AC mains power from the

XND-4’s power outlet.

• No matter what the AC mains power voltage is, the current drawn by all the devices that draw AC mains power from

the power outlet of an XND-4 must not exceed a total of 19.8 amperes.

DMX Connections

Depending on the version, the XND-4 is equipped with 5-pin or 3-pin XLR connectors or with Neutrik etherCON RJ45

connectors.

XLR Connectors

RJ45 Connectors

Each output port is individually optically isolated.

Settings and Menu

General Navigation

The encoder wheel (see page 7) is the primary means for navigating through the menus. Most of the menus arrange

items vertically. In those menus, turn the encoder clockwise to select the item below the currently selected item or

turn the encoder counter clockwise to select the item above the currently selected item. In menus that arrange items

horizontally (e.g. text fields), clockwise means “to the right”and counter clockwise means “to the left”.

Other than that, the encoder wheel also functions as a push button. This button is generally used to confirm a selection

or to navigate to a selected submenu. This manual will also refer to pushing the encoder knob as “push [OK]” or “push

the [OK] button”.

Connection

Com

Data -

Data +

Not connected

Connection

Data +

Data -

Not connected

Com

Shield

Earth

On the right side of the encoder knob, you can find the [Cancel] button (depicted on page 7), which is generally used

to dismiss a selection or to exit a menu.

By keeping the [Cancel] button pressed for at least two seconds, you can always navigate to the Home Screen. From

the Home Screen, the menu is launched by simply pushing the [OK] button.

The following notation is used to describe locations in the menu: Home > Menu > Sub menu > …

For example, the manual could say “navigate to Home > Menu > Art-Net”. This can be read as follows:

Keep [Cancel] pressed for 2 seconds to reach the Home Screen.

Then, press [OK] to get to the menu.

Select Art-Net using the encoder wheel.

After pressing [OK] again to confirm the selection, the Art-Net settings menu is displayed.

Home Screen

The Home Screen shows the IP address of the node as well as the current Art-Net net and

the Art-Net sub-net of the node. The numbers at the bottom of the screen display the 4-bit Art-Net universe of each

of the output ports.The left most number corrseponds to the universe of output 1.

Network Settings

The network settings can be found under Home > Menu > Network.

Home Screen of an XND-4

configured to its default

Art-Net IP address with

Art-Net universe

addressing information

displayed in hexadecimal.

Home Screen indicating

that no signal is applied

to either of the input

ports.

Home Screen of an XND-4

configured to its

alternative Art-Net IP

address with Art-Net

universe addressing

information displayed in

hexadecimal.

Home Screen of an XND-4

configured to a custom IP

address (192.168.10.168)

with Art-Net universe

addressing information

displayed in decimal.

DHCP

Navigate to Home > Menu > Network > DHCP in order to enable or disable DHCP (Dynamic Host Configuration

Protocol). Choose Enable, if you want to have your network configured by a DHCP server. This

would typically be the case, if you connect the XND-4 to a home or office network.

A bullet point is shown next to the currently active setting. Use the encoder wheel to choose

the desired setting and confirm by pressing [OK] in order to change the setting.

Static Settings

All settings under Home > Menu > Network > Static Settings apply only if DHCP is disabled

and are ignored otherwise. From this menu, you can choose the IP address, the netmask and

the gateway address to be used when DHCP is disabled.

IP Address

Use this menu item in order to configure the device’s IP address. When the IP address

configuration dialog is opened, it will look just like the dialog depicted to the right. A box

encircling the first number indicates that the first number is selected. While the first number

(byte) of the IP address is selected, use the encoder wheel in order to choose the desired

value for the first byte of the address, then push [OK] to confirm your selection. The next number will become

selected allowing you to configure the second number. Simply repeat the same steps for the remaining numbers.

After confirming the value of the last byte, the dialog will be closed and the new settings will be applied.

Netmask

In order to configure the netmask, use the same procedure as for configuring the IP address.

The netmask is used internally to compute the network address from the IP address. XND-4

does this by computing the bitwise AND of each byte with the corresponding byte of the IP

address. The bitwise AND of the first byte of the IP address and the first byte of the netmask is the first byte of the

network address and so on.

Gateway

In order to configure the default gateway address, use the same procedure as for configuring

the IP address or the netmask. If the network data sent by the node needs to be routed, you

may want to set this address to the address of your router. In most cases however, this

setting is not relevant.

Set to Primary Art-Net IP

After navigating to the menu item Home > Menu > Network > Static Settings > Set to primary

Art-Net IP, a dialog as shown on the right will appear. Press [Cancel] to abort or press [OK] in

order to apply the following settings:

… Static Settings > IP Address is set to the primary Art-Net IP address (2.X.Y.Z). The values X, Y

and Z are computed from the device’s MAC address.

… Static Settings > Netmask is set to 255.0.0.0.

Set to Secondary Art-Net IP

As Set to Primary Art-Net IP, but sets network settings to the following values:

… Static Settings > IP Address is set to the secondary Art-Net IP address (10.X.Y.Z).

… Static Settings > Netmask is set to 255.0.0.0.

Altri manuali per XND-4

Indice

Altri manuali Swisson Router di rete

Swisson

Swisson XND-8R5 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza