SWIT NDI EFP Manuale utente
User Manual
Ver：C
Thank you for purchasing SWIT products!
Please read this manual carefully before using.
Multi-Camera Production System
* NDI® is a registered trademark of Vizrt Group.
Contents
Statement
Safety Precautions
Introduction
Features
Index of Parts and Functions
The Camera Adaptor
The Intercom Control Panel
Get Started
1. System Connection
2. IP setup
Webpage Settings - Camera Adaptor
1. Channel - Camera Channel configuration
2. Channel - Return Video Source Select
3. Channel - NDI Group Setting
4. Channel - External Sources
5. Channel - Advanced Settings
6. Network - Change IP address
7. User Admin - Log-in ID and Password Setting
8. Firmware Update
Webpage Settings - Intercom Control Panel
1. Channel - Assign Camera Adaptors
2. NDI settings
Indicators
Troubleshooting
Specifications
Dimensions
Packing List
3
4
5
5
6
6
7
8
8
9
10
10
10
11
11
12
12
13
13
14
14
14
15
16
17
18
18
2
Any internal technology of this product (including hardware equipment, software design, and
product trademark) is protected by law, and any violation of the intellectual property rights of
this product will be investigated for legal responsibility.
All the company's brands and trademarks in this product are protected by law. All brands and
trademarks of other companies involved in the product are legally protected by their owners.
In order to better serve the majority of users, the company's products will continue to improve
and develop, and the company reserves the right to modify and improve the products
described in this manual without prior notice.
The warranty period of this product is two years, and the following conditions are not covered
by the warranty:
(1) Man-made damage such as appearance wear and tear;
⑵ Product failure or damage caused by failure to use, maintain and store according to the
instructions;
⑶ When used in a special environment, the signal quality will be attenuated;
⑷ Product damage caused by using a non-product matching power adapter;
⑸ Other faults not caused by product design, technology, manufacturing, quality and other
problems or unauthorized disassembly, repair or replacement parts etc.
If users find problems during use or have suggestions and requirements for our products,
please contact us by telephone, fax, email, etc.
Statement
SWIT Electronics Co., Ltd.
Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone,
Nanjing 210038, P.R. China
Phone: +86-25-85805753
Fax: +86-25-85805296
Email: c[email protected]c
http//www.swit.cc
3
Safety Precautions
Please follow the safety precautions in this manual and operate in the correct way. Our company
guarantees that this product can be used for a long time, but the following situations are not included:
1.Unauthorized disassembly, maintenance or replacement of parts and other operations.
2.Damage caused by accident, including but not limited to lightning, fire, exposure to rain or moisture.
3.The type of power source being used is not within the voltage range allowed for this product.
Warning
Do not let any liquid splash on the product.
In order to avoid electric shock, please do not block or paste the ventilation holes on the product,
do not remove the product cover, or put pins, iron wires, and foreign objects into the gaps in the
ventilation holes.
To reduce the risk of electric shock or fire, do not place this product in rain or moisture.
Danger
Before connecting with any equipment, please turn off the power first, and then operate.
Power socket: To avoid short-circuit electric shock or fire, please confirm that the type of power
socket used is within the voltage range of this product.
Power cord: Do not place any objects or heavy objects on the power cord to prevent the power cord
from being pressed or strained.
Power load: Do not exceed the load on the wall socket, extension cord or other porous sockets to avoid
fire or electric shock.
Lightning: To avoid lightning or long time without use of the product, please remove the plug/external
battery.
User environment
Do not place this product in an unstable place, the product may be seriously damaged due to falling.
Do not place this product near equipment that is too hot, too cold or too humid, or that will cause a
strong magnetic field.
◆
◆
◆
◆
◆
◆
◆
◆
◆
◆
x
4
Introduction
The SWIT NDI EFP system consists of camera adaptors EC-N200 (up to HD) or EC-N200-4K (up to 4K) and
an intercom control panel ET-N80 with all the essential accessories for one-stop setup.
The EC-N200 camera adaptor takes 3G-SDI input from cameras, encoded to an HD NDI stream over an
IP network, and the EC-N200-4K camera adaptor takes 12G-SDI input, and encodes to 4K NDI. Both of
the HD and 4K versions support NDI PGM source decoded and monitoring output via HDMI. You can use
any on-camera monitors with HDMI input, to monitor local camera video and return PGM video in
pic-in-pic mode. The control buttons on the adaptor are available for intercom volume adjustment and
Push-to-talk with the director. There’s on-board TALLY light for cameramen and also extended TALLY
light for the anchor. The camera adaptors support PoE power and V-mount battery power as well.
The ET-N80 intercom control panel can be assigned with up to 8 camera adaptors, and supports link
connection for more channels or for external 3rd party intercom system by 4-wire connector. Directors
can talk to every cameraman individually by pushing button numbers or announce everyone by the
ANN button, instead of selecting intercom channels from webpages.
The NDI EFP system has respected all the operation habits of SDI/Fiber EFP system, and greatly
simplified cable works by using NDI IP solution. You can use any ENG cameras to build up a pure NDI
production system, and all the intercom, TALLY, return video are based on NDI, the high quality and low
latency IP video solution with reasonable network bandwidth.
Encode camera SDI to high bandwidth NDI, HD up to 150Mbps and 4K up to 250Mbps.
Decode PGM NDI in every camera adaptor and display local video and return video together.
Full duplex intercom between cameramen and director.
The director can select camera numbers to talk individually or press ANN to talk to everyone.
The cameraman can initiate the call to director.
Provide dual colors on-board TALLY light and external TALLY light set on the front of the camera.
The camera adaptor supports DC-IN power, V-mount battery power and PoE power.
The intercom control panel can be connected into 3rd party intercom system.
◆
◆
◆
◆
◆
◆
◆
◆
Features
5
Index of Parts and Functions
6
The Camera Adaptor
EC-N200 / EC-N200-4K
SDI LOOP
SDI IN
（1）
（2）
（3）
（4）
（5）
（6）
（7）
（8）
（9）
（10）
（11）
（13）
（12）
（14）
（15）
（16）
（17）
（18）
(1) External TALLY output, 3.5mm jack
(2) Power ON/OFF switcher
(3) Volume Up *
(4) Volume Down *
*Press both to call director
(5) NDI return video Indicator
(6) NDI return video switcher， press in turn:
Local video → Local/Return PIP→ Return Video
(7) SDI input lock indicator
(8) Press the pin to reset
(9) 5-pin XLR headset input
(10) On-board TALLY light
(11) V-mount battery plate (Gold mount option)
(12) D-tap power output from battery
(13) HDMI Monitor out for Local / Return video
(14) SDI loop output*
(15) SDI input*
*EC-N200 up to 3G; EC-N200-4K up to 12G
(16) DC 11-17V input, 5.5/2.1mm jack
(17) RJ45 network cable fixer install position
(18) Gigabit high bandwidth NDI interface *
*EC-N200 up to 1080p50/60, 150Mbps
EC-N200-4K up to 2160p50/60, 250Mbps
7
（1） （2） （3） （4）（5）（6） （7）（8）（9） （10） （11）（12）（13）
（14） （15） （16） （17） （18）
Index of Parts and Functions
The Intercom Control Panel
ET-N80
(1) 3-pin XLR Microphone socket
(2) Mic/Headset switching button
Press down to switch from Headset to Mic
(3) 5-pin XLR Headset socket
(4) Speaker, output when switching to Mic
(5) Volume Down
(6) Volume Up
(7) ANN: Announcement mode
Press to talk to all camera channels
(8) MIC OFF: Turn off the Microphone input
(9) MUTE: Turn off the Headphone/Speaker output
(10) 1-8: Camera Channels 1-8
Press the numbers to talk individually
(11) 4-Wire: External intercom channel
Press to take over external intercom
(12) Power ON/OFF switcher
(13) Press the pin to reset
(14) AC 100-240V 50/60Hz input
(15) AC ON/OFF switcher
(16) DC 11-17V input, 4-pin XLR
(17) External intercom connect, RJ45 4-Wire *
* Pin definition:
(18) NDI network connect, RJ45
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Null
Null
Audio OUT +
Audio IN +
Audio IN -
Audio OUT -
Null
Null
8
Get Started
1. System Connection
Connect all the camera adaptors and the intercom control panel to the NDI network.
PGM
CAM 1
Network Switcher
HDMI output
Local / Return video
External TALLY light
Headset
Headset
15mm Rod Rail Clamp 15mm Rod Rail Camera Base
Install between camera and tripod
NDI
PoE Power
More Camera Channels, NDI switcher, NDI monitor etc.
NDI
4-wire
Camera SDI
Input
3rd Party Intercom System
EC-N200/N200-4K
ET-N80
2. IP Setup
The camera adaptor and intercom control panel
has factory default IP address:
Set computer IP address to the same segment,
and connect directly with the device or through
network switcher, by straight through RJ45 cable.
Launch web browser on the computer,
input 192.168.1.15X to enter configuration
webpage of the camera adaptor, and input
192.168.1.101 to enter configuration
webpage of the intercom control panel.
Input User ID and password to log-in
configuration webpage
9
Get Started
Device
EC-N200/N200-4K
ET-N80
Default IP
192.168.1.15X
192.168.1.101
You can find the default IP address on the product label
Item
User ID
Password
Default
admin
admin
10
1. Channel - Camera Channel configuration
2. Channel - Return Video Source Select
Webpage Settings - Camera Adaptor
Status
Info List
Click to enter
the webpage of
Intercom panel.
All NDI sources in current network Select one source as “Return video”
to output via HDMI to camera top monitor
No special characters accepted
IP address of assigned
Intercom Control Panel
No special characters accepted
Rename and Apply
Indice
Altri manuali SWIT Macchina fotografica digitale
