SwitchBot W1101500 Manuale utente
Motion Sensor
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch •Manuel de l'utilisateur
2
English
3 –13
Čeština
14 –24
Slovenčina
25 –35
Magyar
36 –46
Deutsch
Français
47 –57
58 –68
3
The product user guide contains product features, how to use, and the operating
procedure. Read the user manual carefully to get the best experience and avoid
unnecessary damage. Keep this manual for future reference. If you have any questions
or comments about the device, please contact the customer line.
✉www.alza.co.uk/kontakt
✆+44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Prague 7, www.alza.cz
4
In the Box
Motion Sensor
User Manual
Base
AAA Batteries x 2
Sticker
5
Device Instruction
Mounting Slot
Mounting Slot
Battery Case
Reset Button
LED Indicator Light &
Light Sensor
Fresnel Lens
Base
Magnet
6
Preparation
•A smartphone or tablet with Bluetooth 4.2 or above.
•Download the SwitchBot app
•Create a SwitchBot account and sign in
•(Optional) If you intend to use the Cloud Service feature, you need to set up a
SwitchBot Hub Mini (sold separately) and connect your phone to the internet
Getting Started
Remove the Battery Case. Install two AAA batteries into the battery box following the “+”
and “-“ signs. Then put the Battery Case back.
Open the SwitchBot app and sign in.
On the app, tap the "+" icon on the top right of the homepage. Tap the "Motion Sensor"
icon and follow the instructions to complete the setup.
7
Safety Information
•Keep the device away from humid or hot environments.
•Remove the batteries when not used for long period of time.
•Do not attempt to disassemble, repair, or modify the device.
•Do not use any other batteries than those recommended.
Detection Range
8
Light Sensor
Light Sensor is used for detecting whether it is bright or dark in the target environment.
You can define the threshold for being bright or being dark in the app. Navigate to the
Settings page of Motion Sensor in the app for more information.
How to Use
Reset Button facing up
The recommended height to install Motion Sensor is 1.2m-2m to the ground. The
detection range will be reduced when it is placed lower than 1.2m. There will be
detection blind spots when it is placed higher than 2m.
Reset Button facing down (for Pet Owners)
If you are a pet owner, it is recommended to install Motion Sensor to a spot 0.1-0.2m
higher than your pet(s), with the Reset Button facing down. You can also install Motion
Sensor to a spot slightly lower than your chest to prevent false alarms triggered by your
pets.
Place Motion Sensor without the Base
Place Motion Sensor directly on a table or shelf or stick it to a flat surface using the 3M
Sticker.
Note: Make sure the Lens is facing towards the desired area to be detected and it is
placed close to the edge of the table or shelf.
9
Place Motion Sensor with the Base
Mount the Base to the back or the bottom of Motion Sensor. The Base can be attached
to an iron surface or a magnet.
You can also stick the Base to a flat surface using the 3M Sticker. After Motion Sensor is
properly installed, tilt it to a desired angle.
Note: Make sure the Lens is facing towards the desired area to be detected and it is
placed close to the edge of the table or shelf.
Iron surface
10
Tips for applying the 3M Sticker
Make sure the target surface is dry and clean. Apply pressure to Motion Sensor for 60
seconds after installation. Keep it away from any heat source such as light bulbs.
Battery Replacement, Firmware Update and Factory
Reset
Battery Replacement
Remove the Battery Case. Follow the "+" and "-" marks, replace the old batteries with
new ones. Put the Battery Case back.
Firmware Update
Make sure you have the up to date firmware by upgrading in time.
Factory Reset
Long press the Reset Button for 15 seconds or until the LED Indicator Light is on.
Note: After the device is reset, all settings will be set to the default values and the activity
logs will be erased.
Q&A
Q: It is not sensitive within the detection range set during high temperature.
A: When the room temperature reaches 97°F (36°C), it is very similar to the human body
temperature. Motion Sensor will be less sensitive in this case. Please cool your room by
turning on the AC or fan.
Q: There is a lot of false alarms.
A: Adjust the angle of Motion Sensor to avoid window area, heat sources, and any areas
with constantly moving objects.
Q: How to enable Cloud Service?
A: You need to purchase a SwitchBot Hub Mini (sold separately) and set it up under your
account. Then navigate to the app homepage. If you see a cloud icon showing up on the
Motion Sensor device card, it means it is being scanned by Hub Mini. Navigate to the
Settings page of Motion Sensor and you can enable Cloud Service from there.
Scan the QR code below to view more solutions.
https://support.switch-bot.com
Indice
Lingue:
Altri manuali SwitchBot Accessori
