SynerTech 1 family Manuale utente
P.1of14
Wireless Audio Doorphone
Installation and operation manual
(Model: For 1 family & 2 family)
1.Introduction
Thank you for purchasing this SynerTech product.
Wireless ADP is ideal for your home. Features included: communication, 1 or 2 household call buttons,
and Single door/Garage door release. The operating frequency is at 2.4G Hz.
Full set of wireless audio door phone system includes 1 door station and 1 indoor unit with charger.
Accessories include one wall mounting bracket and screws.
The door station has 1 or 2 household call buttons. When pressed, it allows 2 way speech
communications and will ring only one indoor wireless handset corresponding to that call button. The
wireless handset can be carried from floor to floor.
To obtain the best performance from this product, please read through this manual carefully.
P.2of14
2.Components
A. Name of parts, accessories and indicators for full set of wireless ADP
Handset (Fig.1) Indoor unit Accessories
(Included)
1. DC jack
2. Antenna
3. Built-in speaker
4. LED light
5. Rechargeable Battery
6. Battery door
7. Volume control knob for 8 chorus sound
8. “GARAGE OPENER ” button
9. “DOOR OPENER ” button
10. “TALK ” button
11. Built-in speaker
12. LED indicator
13. DIP switches
14. Built-in microphone
16. Charging contact
15. Metal wall mounting
bracket
17. Charging contact
I. Screws
Handset and indoor unit
Fig. 1
P.3of14
Fig. 2
Door station(Fig.2)
1. Antenna
2. Built-in speaker
3. Door Button
4. LED 1: low battery indicator / coding setting indicator
5. Microphone
6. Name plate (two LEDs ( LED 2 & 3 ) under name plate )
7. DIP switches
8. Terminals
9. Sticker
P.4of14
3.Setting of Wireless System
1) Put the relevant batteries inside the handset & door station
2) Battery pack for handset is provided. Simply plug the battery pack inside the socket near the battery
door. ( See fig.7-2 )
You could select one out of 3 available channels to use.
Make sure the channel between door station and handset is the same.
Handset
Dip switch Channel selection
1. 2-ON 3-ON Channel 1
2. 2-ON 3-OFF Channel 2
3. 2-OFF 3-ON Channel 3
Door station
Dip Switch Channel selection
1. 2-ON 3-ON Channel 1
2. 2-ON 3-OFF Channel 2
3. 2-OFF 3-ON Channel 3
4. should be in “ Off “ position in normal condition
5. should be in “ Off “ position in normal condition
For example, the user choose channel 1 for setting:
The setting procedure is as below:
3) Put the DIP switch 1 to “ ON “ position from the handset.
4) Put the DIP switch 4 to “ ON “ position from the door station. ( For program setting
purpose )
5) Press the call button from the door station.
6) If the identification is done, the LED on the door station would be red & green blinking.
7) Put the DIP switch 4 to “ OFF “ position from the door station
8) Put the DIP switch 1 to “ OFF “ position from the handset
9) Press the call button from the door station to ensure the product is in function.
For setting wireless audio door phone for family two, the procedure is same as
above except the user needs to press the appropriate call button from the door
station during identification.
P.5of14
Select the other channel if any disturbance occurred.
LED indicator from handset: (see fig. 1)
a) When the low battery status from door station, the LED would blink in red & green.
b) When the low battery status from handset, the LED would be on in red.
c) The LED would be in green when battery is charged up.
LED indicator from the door station (see fig.2: point 4)
zLow battery indicator: green light indicates the batteries are in operating level, red light
indicates low battery. Red light would only turn back to green after changing of new
batteries .
zPress the call button from the door station once to activate the setting again after change
of batteries.
zIf the LED turns red & green blinking, it means the successful of code setting between
handset and door station.
Installation Precaution:
Please change to use another frequency if the conversation or images suffer interference from
the surroundings.
When in test model, there will be no door open function
Quality of the images and sound for wireless system will vary according to environmental
conditions, which will also affect the transmission and receiving range. For the best quality,
these functions should be tested before actual installation.
To obtain the best signal transmission, install the indoor unit and door station vertically
on the wall and they should be on the same height from the ground. ( See Fig.6 )
If the signal transmission is weak when using “ table top “ for the indoor unit, install the
indoor unit on the wall vertically to obtain better performance.
P.6of14
4.System Connection
Cable connection (Fig.3)
There are three power sources for this wireless system.
1. Basic mode: (Batteries inside door station only)
Function:
* “Talk”: full duplex communication
* Door open triggering ( Release signal only. If door lock has to be opened, pls connect with access
glass )
* Garage open triggering ( Release signal only not opening garage )
2. Basic mode with 6V access glass (not included in the set) See fig 3
Following the above wiring diagram, connect the wires provided if the access glass, door open switch or
garage open switch are available.
* “Talk”: full duplex communication
* Electricity for opening the door lock
See Fig. 4
P.7of14
* 6V power provide to the door station
* Garage open triggering
ÒCaution: Remove batteries from the door station when using 6V access glass.
3. Basic mode with 12V/24V (through 6V access glass ) (6V access glass not included in the
set) See fig.3
Following the wiring diagram (see fig.3), if 12/24V, door opening &
Garage opening switch are available.
* “Talk”: full duplex communication
* Electricity for opening door lock
* 6V power provide to the door station
* Garage open triggering
* LED “ON” under name plate of door station
ÒRemove batteries from the door station and 6V access glass.
Function of terminal from the door station :
D+ & D- is for the function of door lock triggering.
If connect through access glass, it could switch on the door lock.
G+ & G- is for the function of garage opener triggering.
If connect through access glass , it could trigger the garage opener as well.
When the access glass is used, connect “–“ to GND and “+“ to the terminal LR20.
When 12V/24V is used, connect “–“ to GND and “+“ to the terminal AC/DC ( see fig 3 ).
Fig.4
BK RED RED GREEN BROWN ORANGE YELLOW
Color from the 3M
cable of access glass
P.8of14
Structure of access glass ( not included in the set ) Fig 5-1
Fig.5-2
Connection of terminal block inside the access glass ( See Fig 5-2 )
1) Open the battery cover
2) Install external wires into the terminal block inside the access glass
3) “G-” & “G+” for connecting the garage opener
4) “ +24V ” & “ – ” for connecting 12/24V power source
5) Use the provided clip and screws to hold the wires inside the access glass after connection.
Screw the back case on the wall
( see arrows )
For connecting garage
opener & 12V/24V
3 meter cable provided
Access
glass
P.9of14
5. Preparation for Installation
Recommended installation height (Fig.6)
The above diagram shows the position of the door station and indoor phone unit. Recommended
installation height is approximately 165cm from the ground level for both units. It is usually installed near
the door.
Indoor/door station installation
For indoor unit
1. Referring to the “Recommended installation height” diagram (See fig. 6) to locate and mark the
screw’s positions onto the wall.
2. For the indoor set wall-mounting bracket, make sure the unit is in up direction when placing on to
the wall. The connection between the indoor unit and the corresponding bracket is shown in the
following figure 7-1. Tips of the bracket have to face upwards; otherwise, the phone set will be
upside down.
Step 1: Locate and mark screwing positions on the wall.
Step 2: Drill the screws in but leave 5mm exposed.
Step 3: Plug in the adaptor.
Step 4: Place the indoor unit onto the exposed screw heads and slide until the unit is secured.
P.10of14
Fig. 7-1
Fig.7-2
Installation of battery pack inside handset
Insert the plug from battery
pack to battery socket
inside the handset
After installation, put the battery
socket back to the handset
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali SynerTech Sistema di interfono
