Synology NAS DS3622xs+ Manuale
Synology NAS DS3622xs+
Hardware Installation Guide
Table of Contents
Chapter 1: Before You Start
Package Contents 3
Synology DS3622xs+ at a Glance 4
System Modes and LED Indicators 6
Other LED Indicators 8
Hardware Specication 9
Spare Parts 10
Optional Accessories 10
Safety Instructions 11
Chapter 2: Hardware Setup
Tools and Parts for Component Installation 12
Install Drives 12
Add a Memory Module to Synology NAS 15
Install PCle Add-in Cards 17
Start up Your Synology NAS 20
Chapter 3: System Maintenance
Replace System Fan 21
Chapter 4: Install DSM on Synology NAS
Install DSM with Web Assistant 23
Learn More 23
Synology_HIG_DS3622xs+_20210621
2
Thank you for purchasing this Synology product! Before setting up your new Synology NAS, please check the
package contents to verify that you have received the items below. Also, make sure to read the safety instructions
carefully to avoid harming yourself or damaging your Synology NAS.
Note: All images below are for illustrative purposes only, and may dier from the actual product.
Package Contents
Main unit x 1 AC power cord x 1
RJ-45 LAN cable x 2
Screws for 2.5" drives x 52
Hard drive tray key x 2
Before You Start 1
Chapter
3
4Chapter 1: Before You Start
Synology DS3622xs+ at a Glance
No. Article Name Location Description
1 STATUS Indicator
Front
Displays the status of the system. For more information, see
"System Modes and LED Indicators".
2 ALERT Indicator Displays warnings regarding fan or temperature. For more
information, see "Other LED Indicators".
3 Power Button
1. Press to power on your Synology NAS.
2. To power o your Synology NAS, press and hold until you
hear a beep sound and the Power LED starts blinking.
4 LAN Indicator Displays the status of the network connection. For more
information, see "Other LED Indicators".
5 DRIVE Status
Indicator
Displays the status of each drive. For more information, see
"Other LED Indicators".
6 Drive Tray Install drives (hard disk drives or solid state drives) here.
7 Drive Tray Lock Lock or unlock drive trays.
5Chapter 1: Before You Start
No. Article Name Location Description
8 Power Port
Back
Connect power cord here.
9 Fan Disposes of excess heat and cools the system. If the fan
malfunctions, the Synology NAS will emit a beeping sound.
10 PCI Express
Expansion Slot Supports one PCIe x8 slots (x8 link) add-on card.
11 Reset Button
1. Mode 1: Press and hold until you hear a beep sound to restore
the IP address, DNS server, and password for the admin
account to default.
2. Mode 2: Press and hold until you hear a beep, release the
button immediately, then press and hold again until you hear
three beeps to return the Synology NAS to "Not Installed"
status so that DiskStation Manager (DSM) can be reinstalled.
For detailed information on how to reset your Synology NAS,
please refer to this article.
12 USB 3.2 Gen 1 Port Connect external drives or other USB devices to the Synology
NAS here.
13 Console Port This port is used for manufacturing only.
14 Expansion Port Connect Synology Expansion Unit1to the Synology NAS here.
15 Management Port This port is used for out-of-band management only.
16 1GbE RJ-45 Port Connect RJ-45 network cable here.
17 10GbE RJ-45 Port Connect RJ-45 network cable here.
1 For more information about Synology Expansion Unit supported by your Synology NAS, please visit www.synology.com.
6Chapter 1: Before You Start
System Modes and LED Indicators
System Modes and Denitions
There are 7 system modes in Synology NAS. The system modes and their denitions are as below:
System mode Denition
Powering on Synology NAS is powering on and performing hardware initialization, such as
hardware reset or BIOS initialization.
Shutting down Synology NAS is shutting down as a result of pressing the power button or operation
in DSM.
DSM not ready
DSM is not ready for use. This could either be:
• Synology NAS is powered on, but DSM is not properly installed.
• Synology NAS is currently powering on and initializing services necessary for
DSM to fully function.
• The attached UPS device has insucient power; DSM stops all services to
prevent data loss (enters safe mode).
DSM is ready for use DSM is fully functioning and users can sign in.
Hibernation Synology NAS has been idle for a while and is now in Hibernation mode.
Application
Certain packages/services (e.g., USB Copy and Find me service) while in operation
will control the actions of the LED. After the operation is complete, the LED indicator
will return to its normal state.
Powered o Synology NAS is powered o.
Identify System Modes
You can identify the system mode through the POWER and STATUS LED indicators. Please refer to below table
for more details.
System mode
LED Indicator
POWER STATUS
Blue Green Orange
Powering on Blinking O O
Shutting down Blinking Static O
DSM not ready Static Blinking O
DSM is ready for use Static Static O
Hibernation Static O O
Application Static Switching
Powered o O O O
7Chapter 1: Before You Start
Transitions between System Modes
To better understand the transition between system modes, please refer to below examples:
• Powered on with no DSM installed:
Powered o > Powering on > DSM not ready
• Powered on with DSM installed:
Powered o > Powering on > DSM not ready > DSM is ready for use
• Enter hibernation then wake up from hibernation:
DSM is ready for use > Hibernation > DSM is ready for use
• Shutdown Synology NAS:
DSM is ready for use > Shutting down > Powered o
• Power failure with UPS attached:
DSM is ready for use > DSM not ready (due to power failure, DSM enters safe mode) > Shutting down >
Powered o > Powering on (power has recovered, DSM will reboot)> DSM not ready > DSM is ready for use
8Chapter 1: Before You Start
Other LED Indicators
LED Indicator Color Status Description
DRIVE status
Green
Static Drive ready and idle
Blinking Accessing drive
Orange Static Drive error/Port disabled1
O No internal Drive
ALERT
Red Blinking System error2
O System normal
Rear 1GbE LAN
(on upper side of jack)
Green
Static
1 Gbps connected
Orange 100 Mbps connected
O 10 Mbps connected/No network
Rear 1GbE LAN
(on lower side of jack)
Green
Static Network connected
Blinking Network active
O No network
Rear 10GbE LAN
(on upper side of jack)
Green
Static
10 Gbps connected
Orange 1 Gbps connected
O 100 Mbps connected/No network
Rear 10GbE LAN
(on lower side of jack)
Green
Static Network connected
Blinking Network active
O No network
Note:
1 Please try to restart your Synology NAS or re-insert the drives, then run the HDD/SSD manufacturer's
diagnostic tool to check the health status of the drives. If you can sign in to DSM, please run the built-in
S.M.A.R.T. test to scan the drives. If the problem remains unresolved, please contact Synology Technical
Support for help.
2 If the ALERT LED continuously blinks red, this indicates there are system errors such as fan failure,
system overheating, or volume degrade. Please sign in to DSM for detailed information.
9Chapter 1: Before You Start
Hardware Specication
Item DS3622xs+
Compatible Drive Type 2.5"/3.5" SATA x 12
External Port • USB 3.2 Gen 1 x 2
• Expansion port x 2
LAN Port
• 1GbE RJ-45 for OOB x 1
• 1GbE RJ-45 x 2
• 10GbE RJ-45 x 2
PCIe Slot Gen3 x8 slot (x8 link) x 1
Size (H x W x D) (mm) • 270 x 300 x 340
Weight (kg) 9.8
Supported Client
• Windows 7 onwards
• macOS 10.12 onwards
File System
• Internal: Btrfs, ext4
• External: Btrfs, ext4, ext3, FAT32, NTFS, HFS+, exFAT1
Supported RAID Type
• Basic • JBOD • RAID 0 • RAID 1
• RAID 5 • RAID 6 • RAID 10 • Synology RAID F1
Agency Certication • FCC Class B • CE Class B • UKCA • BSMI Class B
• EAC • VCCI • RCM • KC • UL • RoHS Compliant
HDD Hibernation Yes
Scheduled Power On/O Yes
Wake on LAN Yes
Language Localization
Environment Requirement
• Line voltage: 100 V to 240 V AC
• Frequency: 50/60 Hz
• Operating Temperature: 32 to 104˚F (0 to 40˚C)
• Storage Temperature: -5 to 140˚F (-20 to 60˚C)
• Relative Humidity: 5% to 95% RH
Note: Model specications are subject to change without notice. Please refer to www.synology.com for the latest information.
1Support for exFAT can be enabled by purchasing and downloading exFAT Access in Package Center.
10 Chapter 1: Before You Start
Spare Parts
Visit www.synology.com/products/spare_parts if you need to replace system fans, disk trays, or power supply
units
Model Name Picture Description
Disk Tray (Type D6) 3.5"/2.5" Drive Tray With Lock
FAN 120*25_6 System Fan 120*120*25 mm x 2
PCS Installed In Frame
PSU 550W_1 SFX PSU 550W
Optional Accessories
With Synology accessories, you can customize your Synology NAS to t dierent business environments without
worrying about compatibility and stability. Visit www.synology.com/compatibility for more information.
Indice
Altri manuali Synology Hardware per computer
Synology
Synology RXD1219sas Manuale
Synology
Synology DX1222 Manuale
Synology
Synology DiskStation DS215+ Manuale utente
Synology
Synology M2D18 Manuale
Synology
Synology RX1213sas Manuale utente
Synology
Synology DiskStation DS2415+ Manuale utente
Synology
Synology NAS RS822+ Manuale
Synology
Synology DS1813+ Manuale
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
