Synway SMG1002-2S Manuale utente

SMG1002-2S VOIP Gateway

Installation Manual

VER 1.5

Sywnay Information Engineering Co.,Ltd

www.synway.net

CONTENT

1.Appearance Description ................................................................................................................. 2

1.1 Front Panel ....................................................................................................................... 2

1.2 Rear Panel ........................................................................................................................ 2

2.Hardware Connection .................................................................................................................... 3

3.Basic WEB Settings .......................................................................................................................3

3.1 Network Setting ................................................................................................................. 4

3.2 Protocol And Number Setting ............................................................................................. 5

3.2.1 SIP Protocol And Number Setting ....................................................................................... 5

3.2.2 MGCP Protocol And Number Setting.................................................................................... 6

3.3 Call Route Setting .............................................................................................................. 6

4.Operation Test ............................................................................................................................. 7

SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0

Appearance Description

1.1 Front Panel

Image 1-1 Front Panel

Indicator Description

Power

Power indicator, turn the lights connected to the power supply for the long

bright state.

Active Status indicators, the normal operation of the lamp is flashing

Port 1-2

Port work light, off-hook, ringing, the lights are flashing during a call, the standby is

off.

Tabl e 1 -1 Front panel connectors and LEDs

1.2 Rear Panel

Image 2-2 Rear Panel

The rear

panel

connectors

and LEDs

Description

DC 12V Power cord interface, connect the power cord.

WAN

Equipment upstream interface, when in the 10M Ethernet port rate, the green light, orange light

off; When working in the 100M Ethernet port speed, green and orange lights are on, when the

flow of data out of date, the green light, orange lights flashing.

SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0

LAN

Device configuration interface, when in the 10M Ethernet port rate, the green light, orange light

off; When working in the 100M Ethernet port speed, green and orange lights are on, when the

flow of data out of date, the green light, orange lights flashing.

1-2 FXS connected to a telephone or PBX trunk interfaces.

Table 1-2 Rear panel connectors and LEDs

Hardware Connection

Firstly, using the power supplied in the package box to connect SMG1002-2S to power on it. And WAN port

SMG1002-2S Series integrated access devices connected to the hub or switch, as shown in Figure 2-1.Making

SMG1002-2S to connect with the service network, and then connecting the PC to the LAN port of SMG1002-2S,

making data configuration for SMG1002-2S and Port1-2 connected to the phone.

Figure 2-1 SMG1002-2S Series Integrated Access Device as a proxy server connection

Basic WEB Settings

Entering the Web interface to configure the SMG1002-2S . The default of LAN port address is 192.168.11.1.

SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0

Set the IP address of PC which is connected with LAN port to the same network segment. And then, open the IE

browser, enter the LAN port IP in the address bar to login the WEB network management device for business

configuration. WEB default user name and password are: admin.

Figure2-6 WEB Login Interface

3.1 Network Setting

The WAN port of SMG1002-2S supports 3 different operating modes which are DHCP, PPPoE, and Static. Users

can set “the WAN configuration” in the Web, such as IP address, mask, IP address, DSN and so on. Make

SMG1002-2S accessing to business network normally.

SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0

Figure3-2 WAN Setting Interface

3.2 Protocol And Number Setting

SMG1002-2S supports both SIP and MGCP protocols. Before the configuration of protocol and number,

SMG1002-2S needs to determine the type of VOIP protocol that the softswitch communicates with SMG1002-2S

and obtain information such as softswitch address and account number.

Usually, SMG1002-2S will not support the different VOIP protocols at same time, so when setting the protocol

and number, users only need to set the parameters consistent with the softswitch’s protocol. The following two

VOIP protocol are supported by SMG1002-2S, registration of the specific configuration of the softswitch

instructions depend on the actual situation to configure:

3.2.1 SIP Protocol And Number Setting

Fill sip server's domain, under normal circumstances, and fill the same SIP server IP address for the domain;

butt IMS, IMS platform to fill in the domain name.

When registering softswitch with SIP protocol, Users should set the “active server” and “domain” as softswitch

IP addresses in“SIP configuration” in WEB, and set the “active server port” as same as “softswitch registered

Port” .This equipment SIP signaling port, the default value is 5060.

Click Sip Settings to modify in the interface below

Figure3-3 SIP Setting Interface

After the above settings, in the "Number Configuration" -> "Number Batch Edit", assign a number to the service

port of the device, set the uplink protocol of the port to "SIP", set the "Phone number ”and “Authentication

Name" as assigned user account name of softswitch, "registered password" set to the corresponding user

SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0

account password, and open the port registration.

3.2.2 MGCP Protocol And Number Setting

Setting the “MGCP address ” as “softswitch’s IP address”, and “MGCP port ” should be set as same as “MGCP

protocol port”,When SMG1002-2S registers softswitch with MGCP protocol, the default port of MGCP protocol is

2727.The Local Domain Name is set to the device domain name specified by the Softswitch, and the End Node

Prefix is set to the softswitch prefix of the endpoint name assigned to the device.

For example, the softswitch assigns 32 user nodes to the device "weych". The node ID of each user is "aaln /

01-aaln / 2". The MGCP configuration of the SMG1002-2S is shown in the following figure. The local domain

name is set to "weych" The node prefix sets "aaln /" with the same 32 user nodes.

After making the above settings, assign the number to the device port in the "Number Configuration" ->

"Number Batch Edit", set the port upstream protocol to "MGCP", and set the phone number to the suffix of the

name specified by the softswitch Section, while opening port registration. For example, the softswitch assigns

32 user nodes to the device "weych". The node ID of each user is "aaln / 01-aaln / 2". Set the telephone number

of the port as 01,02 as shown in the figure below.

3.3 Call Route Setting

When using the SIP protocol, SMG1002-2S supports adding different call rules to define the number conversion

and routing IP in routing table. In WEB setting interface, Select” Call Path”, users can see a default

“DigitMap-Default”, besides this default Call Path, user can manually add his own. When the call path is set,

users can go to “Port Settings””Basic Settings” to choose the one to activate, as shown below:

Figure3-7 Call Path Setting Interface

By Clicking “Edit”, User can check the detailed rules, call rules are consisted by “0-9, .,*,#,X”(represents

number 0-9,)and []” For example, [1,3,4-6,9]=13,4,5,6,9.

When Routing IP is 0.0.0.0, then the call will be sent to the server address edited in “SIP Settings; If the routing

IP is a specified IP then the calls will be forwarded accordingly(p2p), as below.

SMG1002-2S VOIP Gateway (SIP) Installation Manual VER 1.0

Figure3-8 Edit call path interface

Operation Test

After the completion of configuring the operational data, reboot the device and log in to the WEB configuration

interface. And then check the registration status of each port in “Number Configuration”, the status of the port

is "registered" as soon as the registration succeeds. And connect The SMG1002-2S Port1-2 to telephone for dial

test, test SMG1002-2S the caller and the called and other business conditions.

Figure 3-11 phone number setting interface

Synway Information Engineering Co., Ltd.

HQ Add: Synway R&D Building,NO.3756,Nanhuan Rd.Hangzhou,P.R.China

Tel: +86 571 88861158 Fax: +86 571 88850923 Email: marketing@synway.cn

Indice

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente