System Sensor RA400Z Manuale utente

D220-01-00 1 I56-508-05

RA400Z and RA400ZA (Canadian)

Remote Annunciator

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

General Information

The National Fire Protection Association has published

codes, standards, and recommended practices for the

installation and use of the above appliance. It is recom-

mended that the installer be familiar with these require-

ments, with local codes, and any special requirements of

the local authority having jurisdiction.

The models RA400Z & RA400ZA remote annunciators

are polarized devices designed for both conventional and

intelligent applications. They have been designed using

an active current regulator so that the maximum current

required from the system is 10mA when the input voltage

is within the specified voltage range.

Installation

The remote annunciator is intended to be mounted to a

single gang electrical outlet box. The wiring must be in

compliance with all codes. The device must be operated

within its published specifications.

Wire the remote annunciator according to the instructions

supplied with the device being monitored. Polarity of the

incoming wires must be observed and connected to the

proper terminals “+” and “–”. (See Figure 1.)

The tab on the back of the RA400Z and RA400ZA must

be broken off for use with most System Sensor intelligent

systems. (See Note 1 and Figure 4.) After tab is broken, the

input voltage for the RA400Z and RA400ZA is limited to 18

volts minimum.

H0355-00

Specifications

Voltage Range

Conventional System: 3.1 to 32 VDC — Do not break tab.

Intelligent System: 18 to 32 VDC — Break tab.NOTE 1

Maximum Alarm Current: 10 mA maximum.

Temperature Range: –10° to 60°C (14° to 140°F)

NOTE 1:

CAUTION

Do not break tab when using an RA400Z or RA400ZA with an intelligent 4-wire duct detector (such as the System Sensor

model DH500ACDC or DH200RP).

BEND TAB DOWN

TO BREAK

FOR USE WITH MOST

INTELLIGENT SYSTEMS.

D220-01-00 2 I56-508-05

THE REMOTE ANNUNCIATOR WILL NOT WORK IF THE DEVICE IT IS

CONNECTED TO IS NOT POWERED. The remote annunciator gets its

power from the device to which it is connected. If for any reason, the

device being monitored loses power, the remote annunciator will not pro-

vide the intended visible signal.

THE REMOTE ANNUNCIATOR MAY NOT BE SEEN. The model RA400Z is

suitable for direct viewing and is in compliance with existing Underwriters

Laboratories’ standards. The device must be sited in a location where it

can be seen by the intended parties. The device must not be installed in

WARNING

The Limitations of Remote Annunciators

direct sunlight, or areas of high light intensity where the visible signal

might be disregarded or not seen.

THIS DEVICE IS DESIGNED TO WORK SPECIFICALLY WITH SYSTEM

SENSOR PRODUCTS. Interconnection with devices other than System

Sensor’s may result in unsatisfactory operation. Consult device manufac-

turer for compatibility.

THE REMOTE ANNUNCIATOR IS NOT INTENDED TO BE A VISIBLE

WARNING SIGNAL.

H0356-00

Figure 1:

H0354-00

From

Monitored

Device

Figure 2:

(See Note 1)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali System Sensor Accessori

System Sensor

System Sensor 2351PTIRAUS Manuale utente

System Sensor

System Sensor 2551HR Manuale utente

System Sensor

System Sensor 200 Series Manuale utente

System Sensor

System Sensor SPECTR Alert ADVANCE CHSR Manuale utente

System Sensor

System Sensor 22051TLE Manuale utente

System Sensor

System Sensor 22051E-RF Manuale utente

System Sensor

System Sensor SENS-RDR Manuale utente

System Sensor

System Sensor 5551 Manuale utente

System Sensor

System Sensor B200SR-LF-WH Manuale utente

System Sensor

System Sensor B501AP-IV Manuale utente

System Sensor

System Sensor B200SR Manuale utente

System Sensor

System Sensor 2251CTLE Manuale utente

System Sensor

System Sensor 5251RB-WP Manuale utente

System Sensor

System Sensor 22051E Manuale utente

System Sensor

System Sensor 2251TEM Manuale utente

System Sensor

System Sensor FAAST FL2011EI-HS Manuale utente

System Sensor

System Sensor 22051TEI Manuale utente

System Sensor

System Sensor SMB500 Manuale utente

System Sensor

System Sensor 2251TM Manuale utente

System Sensor

System Sensor RTS451 Manuale utente

System Sensor

System Sensor 2351BR Manuale utente

System Sensor

System Sensor 7251 Manuale utente

System Sensor

System Sensor B401BH Manuale utente

System Sensor

System Sensor 2251BR Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente