Systems & Technology careu u1 plus Manuale utente
CAREU U1
PLUS
User
Gu
CAREU U1 PLUS
User
Guide
Version: 0.1
Reference No.: AVL
Date: 2014/12/26
SYSTEMS & TECHNOLOGY
COR
General Information
If any breakdown occurs due to the operation of the described product or
users’ improper handling in accordance with the instructions of the
document, S&T shall be liable for the General Conditions based on the
delivery of the described product and the content of the document. This
product is not designed for the use of life support appliances, devices or
systems and thence a malfunction of the product might reasonably be
expected to make personal injury. S&T customers using or selling this
product for such applications will take the risk on their own; therefore, it must
be agreed S&T will be fully indemnified from any damages due to illegal use
or resale. All information in this document is subject to change without notice
at any time.
Disclaimer
The information, specification, images and photos in this user guide are
subject to change without notice and without obligation to notify any person
of such revision change.
Copyright
This user guide, including all photographs, illustrations and software, to
name a few, is protected under international copyright laws, with all rights
reserved. This document contains confidential, restricted and proprietary
information that it has been exclusively prepared for the internal use of
certain designated S&T employees, and may not be duplicated or distributed,
in whole or in part, without the prior written consent of S&T’s authorized
delegates. Any illegal copying and disclosure of the document are absolutely
prohibited, and violators are liable to the damages caused.
© Systems & Technology Corp. All Rights Reserved
Table of Contents
Chapter 1 introduction. ..................................................................................... 1
1.1Features........................................................................................................ 1
1.2 Scope ........................................................................................................... 1
1.3 Overview ..................................................................................................... 1
1.4 Hardware Architecture ................................................................................ 3
1.5 Related Document ....................................................................................... 3
Chapter 2 Taking a Tour of CAREU U1 PLUS ................................................... 4
2.1 Dimensions .................................................................................................. 4
2.2 PIN Assignment ............................................................................................ 4
Chapter 3 Getting Started with CAREU U1 PLUS ............................................ 6
3.1 Device Configuration.................................................................................... 6
3.2 Communication Settings .............................................................................. 9
3.3 GPS Tracking Configurations ...................................................................... 10
3.4 Firmware Upgrade ..................................................................................... 12
Chapter 4 Technical Specification ................................................................ 13
Chapter 5 Regulation ................................................................................... 16
Chapter 6 Safety Information....................................................................... 17
1
Chapter 1 introduction.
Designed with the latest GPS technology, the CAREU U1 PLUS delivers positioning
message by wireless transmission to GIS platform, and then helps back-end users
proceed with the analysis and the applications of vehicle transport, management,
anti-theft, security and tracking.
A microcontroller can probe location and command data at regular intervals, derive
actions from location, peripheral and control data, and execute such actions.
Peripheral data indicates the status of various peripherals connected to and/or
controlled by the device. Among the best features of the CAREU U1 PLUS Vehicle
Tracker, in particular, they transmit data in ASCII mode (Intellitrac X Series
compatible mode) or binary mode.
1.1 Features
● SMS,GPRS/UMTS/HSPA TCP/UDP, USSD, FTP
● Real-time tracking (Time, Distance Interval or Intelligent Mode, and Heading)
● Firmware upgrade over the air ( form FTP)
● Journey report wireless download
● Battery low alert
● Geofence reports
● Mileage reports
● User-defined reports
● 6-Axis Sensor
● NMEA-0183 Output for Navigation
● GPS Antenna Destroyed Alarm
● CAN BUS interface (optional)
● 10/100 Ethernet (optional)
1.2 Scope
This document will guides you to start the CAREU U1 PLUS Vehicle Tracker.
However,as this document contains basic device configuration only, please see the
CAREU U1 PLUS Protocol Document for the advanced information.
1.3 Overview
Device Overview
2
1. GPS LED
2. GSM LED
3. Power Connector
4. RS-485/CAN Connector
5. I/O Connector
6. Serial Connector
7. GSM Antenna Connector
8. GPS Antenna Connector
9. Reset Switch
10. RJ45 Connector
11. Remote Receiver Connector
3
1.4 Hardware Architecture
As hardware is concerned, the CAREU U1 PLUS is comprised of a micro-controller,
regulator, GPS receiver, 2G/3G modem, G-Force sensor, flash memory data storage.
● Users can connect PC's Hyper Terminal to the diagnostic setting port for the
AVL
configuration.
● G-Sensor is for car accident prevention, car tow-away warning and power
management.
FLASH I/O
SENSOR
MCU
GPS RS232
Powe
Modem
1.5 Related Document
CAREU U1 PLUS Protocol Document
4
Chapter 2 Taking a Tour of CAREU U1 PLUS
2.1 Dimensions
Dimensions (L x W x H): 72mm x 108mm x 31mm
2.2 PIN Assignment
1
2 4
3
2 4
31
6
5 9
8
7
10
13
12
11
16
15
14
SERIAL PORT
I/O
POWER
4
31
6
5
2 8
7
10
921
20
19
18
17
RS-485 / CAN
24
23
22
PWR Connector
Pin#
Signal Name Description IO Electrical Characteristic
1 DC IN Power supply input I VI = DC8 to 30V,
2 GND Signal ground G
3 Ignition Ignition(ACC) Input I DC Vin = +30 ~ +7.5V (Active high)
4 Output1 Open-Collector
Output1
O Imax = 300mA
I/O Connector
Pin# Signal Name Description IO Electrical Characteristic
1 Analog Input 2 Analog input 2 I DC VIN = +30V ~ 0V
2 Input 4 Positive/ Negative I
DC VIN = +3
0V ~ +
7.5
V (High Active)
DC VIN = 0V (Low Active)
3 Input 1 Negative Trigger I
DC VIN = 0V (Low Active)
4 Input 2 Negative Trigger I
DC VIN = 0V (Low Active)
5 Analog Input 1 Analog input 1 I DC VIN = +30V ~ 0V
6 GND Signal ground G
7 Output 2 Open-Collector O Imax = 300mA
8 Output 3 Open-Collector O Imax = 300mA
9 Output 4 Open-Collector O Imax = 300mA
10 Input 3 Positive /Negative I DC VIN = +30V ~ +7.5V (High Active)
DC VIN = 0V (Low Active)
5
SERIAL Connector
Pin# Signal Name Description IO Electrical Characteristic
1 Vout1 Supply voltage
output O Vo = 5V ( Vout 1~2 Total Imax = 500mA )
2 GND Signal ground G
3 TX1 RS232 Data output O
4 RX1 RS232 Data input I
5 Vout2 Supply voltage
output O Vo = 5.0V, (Vout1~2 Total Imax = 500mA)
6 GND Signal ground G
7 TX2 RS232 Data output O
8 RX2 RS232 Data input I
9
1-Wire 1-Wire Data
input/output I/O (BOM optional)
Vout3 Supply voltage
output I Vo = 5.0V, (Vout1~3 Total Imax = 500mA)
(BOM Optional)
10 GND Signal ground G
11 TX3 RS232 Data output O If 1-wire version, this pin unused.
12 RX3 RS232 Data input I If 1-wire version, this pin unused.
13 SPK+ Audio output O
14 SPK- Audio output O
15 MIC+ Microphone Input I
16 MIC- Microphone Input I
17 RXA RS485 input A I Full Duplex (*Half Duplex setting by
jumper)
18 RXB RS485 input B I Full Duplex (*Half Duplex setting by
jumper)
19 TXA RS485 output Z O Full Duplex (*Half Duplex setting by
jumper)
20 TXB RS485 output Y O Full Duplex (*Half Duplex setting by
jumper)
21 RS485_GND RS485 ground R_G
22 CANH CAN High I
23 CANL CAN Low I
24 CAN_GND CAN ground C_G
6
Chapter 3 Getting Started with CAREU U1 PLUS
To install the the CAREU U1 PLUS device, follow the instructions below for
basic operations
3.1 Device Configuration
1. Connected the serial port 1 to PC COM port
2. In Windows desktop, click Start | All Programs | Accessories | Communications
| HyperTerminal.
3. If you are prompted to input the information of your location, complete them to
proceed.
4. On the File menu of HyperTerminal, click New Connection.
5. In the Name box, type a name that describes the connection. In the Icon box, click
an appropriate icon. Press the OK button to proceed.
6. For Com port properties, configure as follows: Baud Rate --> 115200 bps
Data Bits --> 8
Parity --> None
7
Stop Bits --> 1
Flow Control --> None
7. In the connection that you have just set up, click File | Properties. Select the
[Connect To] tab. From the [Connect using] drop down list, select the correct com
port.
8. In the File menu, click Properties. Click the [Settings] tab. Press the ASCII Setup
button.
Indice
Altri manuali Systems & Technology GPS
