TA HORIZONS MIGHTY EDGE 33 Guida all'installazione
TA HORIZONS 33’’ MIGHTY EDGE
ASSEMBLY INSTRUCTION MANUAL
Page 1
Technical Data-
Wingspan : 33"
Length : 35”
AUW : 180-220g
(Depends upon the setup used)
Setup Recommendations (Not Included)-
Motor : 18-22G 1800-2300KV Outrunner
(T-Motor AS2304 1800KV Recommended for Super Light Setup)
ESC : 12-16 amp
Servos : 3Pcs 9gms each
Propeller : 8-9” electric
Battery : 450-600Mah 2-3S Lipo
Page 2
WARNING INFORMATION & SAFETY INSTRUCTIONS
Thank you for choosing TA Horizons.
If you have any questions, please contact us aforementioned email address.
Please read the entire manual thoroughly before you begin
to assemble this model.
Website: www.tahorizons.com Email: [email protected]
This R/C airplane is not a toy! Read and understand the entire manual before assembly. If
misused, it can cause serious damages to life and property. Fly only in open areas. If you
are not an experienced pilot and airplane modeler you must take the help of an experienced
pilot or an authorized flight instructor for the building and flying of this model aircraft.
These instructions are suggestions only on how to assemble this model. There are other ways &
methods also to do so. TA Horizons has no control over the final assembly because it specifically
depends upon the knowledge and experience of the person involved directly in its handling,
or the manner in which the model is assembled, radio gear installed, and electronic parts are used
and maintained. Thus, no liability is assumed or accepted for any damages resulting from the use
of the assembled model aircraft. By the act of using this user-assembled product, the user accepts
all the resulting liabilities. In no event shall TA Horizons’ liability exceed the original purchase price of
the kit.
The user is advised to comply with all local laws and regulations. TA Horizons will have no
responsibility over the user assembled product and its end use. TA Horizons has the right to change
any content on the website, product information brochure, or the manuals, at any point of time
without any prior notice.
TA Horizons checks each plane before shipping to ensure that each kit is in fine condition. We
have no bearing on the condition of any component parts damaged by use, modification, or in
assembling of the model. Inspect the components of this kit upon receipt. If you find any parts
damaged or missing, please contact TA Horizons immediately. We will not accept the return or
replacement of parts on which assembly work has already begun.
Our goal is to bring to you the best in quality and state of the art radio controlled aircrafts.
For those who demand the ultimate in precision, or for those who are just a weekend flyers and
want to feel good about their flights, our planes are in development from many months and
tested to ensure that these aircrafts will give you the best possible performance. We sincerely
hope that our products can provide the same thrill to you that we experience in this hobby.
Page 3
Kit Contents
1. EPP Parts
3. Carbon Rods / Strips / Tubes
1
2
3
4
5
1
2
3
1.2mm CF Control rods
RUD 420mm L X 1
ELE 380mm L X 1
AIL 100mm L X 2
Undercarriage sq.tube
D 2x3mm L 225mm X 2
41mm Wing Truss Rods
L 330mm X 4
51mm Fuselage truss rods
150mm L X 12
200mm L X 2
100mm L X 2
Carbon Rods / Strips / Tubes
Please Note: After removing kit from shipping
box, lay each piece flat on a hard surface, this will
allow the airframe to straighten out if lightly bent
from shipping. Do not worry since EPP is very
pliable and can be bent back if out of shape.
Double check that you have all the above
pictured items. If any of the airframe or hardware
items are missing, contact TA Horizons before
starting your build.
Flat 5X1mm 675mm L front wing spar
Flat 5X1mm 325mm L elevator spar
Flat 3X0.5mm 645mm L aft wing spar
Flat 3X0.5mm 200mm L rud renf
Flat 3X0.5mm 150mm L fin renf
Flat 3X0.5mm 415mm L fuse renf X2
Flat 3X0.5mm 170mm L tail renf
Flat 3X0.5mm 180mm L vertical fuse renf
EPP Parts
1
2
3
4
5
6
Fuselage
Wings
Horizontal stabilizer
Horizontal profile section
Wing truss supports X 2
Landing gear cover
7
8
Side Force Generators X 2
Wheel Pants X 2
9Aileron truss support X 2
6
61mm Aileron truss rods
200mm L X 6
150mm L X 2
1
2
3
4
4
5
6
8
7
9
1
2
3
4
5
6
7
Polycarbonate parts
Fuselage assembly jig
EPP Wheels X 2
150mm velcro
Quick links X 8
Selftaping screw X 8
3D printed wheel bracket X 2
Hardware Parts
8
9
40mm 2mm CF Wheel Shaft X 2
60mm CF strip
2. Hardware / Small Parts
2
3
4
7
8
9
1
56
Page 4
TOOLS AND BUILDING MATERIAL REQUIRED
• Heat Gun
• Tape Measure and Ruler
• Black Sewing Thread
• High Viscosity CA
• CA Spray Activator
• Hobby Knife w/new Blade
• Needle Nose Pliers
• Wire Cutters
• Low Temp Hot Glue Gun
• Scissors
• Small Phillips Screw Driver
• Thin CA
• Alenkey
Page 5
The Build
Please Note: Few pictures shown below are of different plane and for reference purpose only.
1.
Bend them back on to each other as shown and let set for at least 2
hours. This will help to loosen up the movement of the surface.
(This is mandatory step)locate the hinged items as shown above, 2. Locate the 5mm X 675mm CF Spar shown in the picture above.
3.
edge of wing, like shown above.
Apply a thin layer of HV Cyno on CF Spar, and glue it on the leading 4. Make sure to lay down the wing on the flat surface while glueing the
CF stripe.
5.Locate the 3X0.5mm 645mm Stripe, for rear wing re-inforcement,
insert the stripe vertically into the precut slot, make sure it is completely
inserted into the slot.
6. Use thin cyno to glue this stripe (Do not use HV CA), use spray
activator to cure it.
1 2
34
6
5REGULAR THIN
CYNO ONLY
3X0.5X645mm
5X1X675mm
Page 6
The Build
Please Note: Few pictures shown below are of different plane and for reference purpose only.
7. Locate the 1X5mm 325mm L stripe,
Use a spray activator (Kicker) to cure, wipe off the excess glue if
needed.
Glue it in the pre-cut groove. 8. Apply a thin layer on gluing surface.
9. Use a spray activator (Kicker) on the other surface. 10. Glue both the parts together, hold it for a few seconds. Match the
center with the groove shown in the above image.
11. Lay down the shown parts on the flat surface with wax paper
on it and glue it together.
12. Lay down the shown parts on the flat surface with wax paper
on it and glue it together.
8
9
11 12
7
1010
5X1X325mm
GEL GLUE (HV)
ACTIVATOR
The Build
Please Note: Few pictures shown below are of different plane and for reference purpose only.
13.Locate the 3X0.5mm 170mm stripe for tail re-inforcement, insert
the stripe vertically into the precut slot, make sure it is completely
inserted into the slot.
14. Use thin cyno to glue this stripe, use spray activator to cure it.
15. The horizontal piece of the fuselage also uses flat carbon fiber
spanning the entire length from the rear wing spar to the horizontal
stab spar, locate the 3X0.5mm 415mm stripe, insert the stripe
vertically into the precut slot like shown above.
16. Use thin cyno to glue this stripe, use spray activator to cure it.
17. Here are 2 X 415mm stripes inserted and glued from the rear
wing spar to the horizontal stab spar.
18. Wipe off the excess glue if needed.
14
13
15 16
Page 7
17 18
REGULAR THIN
CYNO ONLY
3X0.5X415MM
3X0.5X170MM
3X0.5X415MM
The Build
Please Note: Few pictures shown below are of different plane and for reference purpose only.
19.Time to do Aileron trussing. 20. Use the yellow marked part of foam as aileron truss support.
21. Locate the triangular joiner that will be placed on the underside of
each aileron. Once you make sure that it fits clean and snug into the
cutout, you can glue this piece in and repeat to the other side.
22. Locate the 3 X 200mm and 1 X 150mm 1mmD rods, With the
joiner in place, you can now begin the process of bracing the aileron.
This will include four carbon fiber rods in the configuration shown above.
23. Repeat the process for the other side aileron. 24. We can now began the vertical fuselage installation, use the blade
to separate both the parts.
Page 8
200MM RODS 150MM ROD
19
23
21
2020
22
24
Page 9
The Build
Please Note: Few pictures shown below are of different plane and for reference purpose only.
25.Apply a thin layer of HV CA to the mating surfaces of the lower
vertical fuselage.
26. Bring the two pieces together. You will have a little time to work with
and adjust for squareness.
27. It is extremely important to make sure that the bottom part of the
fuselage stays 90 degrees to the horizontal fuselage while the glue is
setting. Use the supplied jig for this task.
28. Locate the above parts for the undercarriage assembly
29.Glue the center rim over the supplied black EPP wheels with center
hole aligned using HV CA (Do it for both the sides of wheels).
30. Here the supplied (3mm dia 225mm) tube and (2mm dia 40mm)
wheel shaft are glued on the wheel bracket.
GEL GLUE (HV) ACTIVATOR
GEL GLUE (HV)
25
27
29 30
26
28
Page 10
The Build
Please Note: Few pictures shown below are of different plane and for reference purpose only.
31. Optionally use a heat shrink tubing for better cosmetic finish. 32. Glue the shown parts over the pre cut slots, for landing gear
assembly.
33. Glue the shown parts over the precut slots using the HV CA and
cure everything together using the kicker. Match the shown red area
with the precut slot in the EPP.
34. Install the undercarriage that we have prepared like shown in the
above image. Both wings are having different positioning of UC slots
with 3mm difference.
35.Put a drop of HV CA over the joints and spray everything together. 36. Put a drop of HV CA over the joints and spray everything together
FORWARD SLOT
BACKWARD SLOT
GLUE HERE
GLUE HERE
31
33
35
32
34
36
Indice
Altri manuali TA HORIZONS Giocattolo
