tanning essentials Rapid Guida all'installazione
RAPID - TRAINING MANUAL
www.tanningessentials.co
SIMPLE TANNING SYSTEMS built purposely for a perfect spray tan.
1
6
2
3
3
2
WELCOME
Thank you for choosing the Tanning Essentials Rapid Spray Tan System. Please read the
following to help assist you with the set up and maintenance of your spray tan unit.
You can also view the full video on Rapid Spray Tan System Set Up, Maintenance and
Troubleshooting via You Tube
QUICK SET UP GUIDE
The Tanning Essentials Rapid Spray Tan System contains:
1 x Rapid Spray System 2 x Solution Cups
2 x Rapid Spray Applicators 1 x Power Cord
(Optional 1 gun version also available) 1 x Wall Mounting Set
1 x Rapid Spray Hose 1 x Manual (not pictured)
1
2
3
4
5
6
www.tanningessentials.co
SPRAY SYSTEM
SPRAY APPLICATOR
www.tanningessentials.co
Carry Handle
ON/OFF Switch
Power Plug
Socket
Washable Filter
(Underneath Unit)
Cup
Holders
Control Panel
Hose Connector
Shock Absorbing
Feet
Adjustable
Spray
Nozzle
Solution Cup
Solution Dial
(On Side)
Spray Trigger
Handle
Hose Connector
(Underneath)
SPRAY APPLICATOR
www.tanningessentials.co
STEP 1
Unscrew the solution cup and fill ¾ full. Overfilling the solution cup
may cause leaks.
STEP 2
Insert solution cup and screw tightly.
STEP 3
Set nozzle by turning. Vertical position for up and down and
horizontal position for left to right spraying.
STEP 4
Adjust solution dial on the back of the applicator to choose the
amount/flow of solution you would like to dispense. A higher setting
will result in more solution being distributed. Setting your applicator
on 2-4 for the body and 2 for the face are best recommended.
STEP 5
Attach hose- Ensuring the flat edge of the socket is facing upright.
Align the prongs from the hose into the applicator fittings and screw
the connection clockwise until firmly in place.
SPRAY UNIT
www.tanningessentials.co
STEP 1
Attach hose to unit. Pull connection back exposing the prongs,
ensuring the groove is facing the top, line up the prongs to meet
the unit, release the connection and screw in clockwise until firmly
in place and sitting straight.
STEP 2
Attach Power cord and turn power on at the wall switch.
STEP 3
Turn on your unit and choose your desired settings. Recommended
power setting is 3 depending on the solution and speed of
application. The unit is controlled via touch technology that is
located on the front of the spray unit.
SPRAY UNIT MAINTENANCE GUIDE
STEP 1 Clean the spray unit with a cloth. Avoid using anything abrasive. Windex
and Mr. Sheen are useful products for maintaining the gloss finish of your
spray unit.
STEP 2 Clean the filter. Remove the filter from the base of the unit and rinse in
warm water. Wait until filter is completely dry before re-fitting. Positioning
the spray unit behind the spray technician when in use will ensure the unit
stays cleaner for longer.
www.tanningessentials.co
SPRAY APPLICATOR MAINTENANCE GUIDE
STEP 1 Remove hose.
STEP 2 Unscrew solution cup and empty any excess solution. It is recommended
that this be done over a sink or a wet area.
STEP 3 Rinse the empty solution cup with warm water.
STEP 4 Refill the cup with warm water and screw back into the applicator, fix the
solution dial to ‘C’ and spray until the water runs clear. Rinse and repeat
if required
STEP 5 Empty solution cup and re-set the solution dial on the back of the gun
to the regular spray setting.
STEP 6 Wipe any excess water from the applicator with a cloth and leave out
to dry.
www.tanningessentials.co
Maintenance on the Applicator must be run at the end of each day the applicator is used.
SECONDARY SPRAY APPLICATOR MAINTENANCE
www.tanningessentials.co
Secondary maintenance must be run on the applicator every 2-4 weeks or when required.
Secondary maintenance will deliver a more thorough clean to prevent or clear any blockages
and uphold the applicators performance.
O-RING SEAL
FLUID
NOZZLE
ADJUSTABLE
NOZZLE
RETAINING
RING
FLUID
NEEDLE
SECONDARY SPRAY APPLICATOR MAINTENANCE
www.tanningessentials.co
TROUBLESHOOTING - BLOCKED NOZZLE OR CONTINUOUS SPRAY
WITHOUT PRESSING THE TRIGGER
STEP 1 Locate and unscrew retaining ring. To release; turn retaining ring in an
anti-clockwise motion.
STEP 2 Gently pull on the adjustable nozzle to remove.
STEP 3 Fit an 8mm spanner to the flat edges of the fluid nozzle and turn
anti-clockwise to unscrew.
STEP 4 Ensure you do not misplace the o-ring seal, which is located behind the
fluid nozzle .
STEP 5 Once removed, visually inspect the fluid nozzle for small particles or
blockages - rinse thoroughly with hot water.
STEP 6 Gently wipe the fluid needle to clean and remove any debris (the fluid
needle should not be removed from the applicator at any time).
STEP 7 Once visually clear of any debris, re-attach fluid nozzle, ensuring the
O-ring is in position, then use the spanner (8mm) to gently tighten back
into place.
STEP 8 Replace adjustable nozzle and rotate back into position.
STEP 9 Repeat previous step, this time with the retaining ring.
TROUBLESHOOTING
If you are experiencing problems with this unit, in the first instance please carefully read the
relevant sections of the User Manual and the Troubleshooting section below. If you cannot
solve your problem please contact your supplier for further assistance.
www.tanningessentials.co
PROBLEM CAUSE WHAT TO DO
My solution is
bubbling from
the cup
Seal is not in properly
Solution Cup is not screwed in
correctly
The cup is cross-threaded
Solution cup is overfilled
Fit the gun seal correctly.
Unscrew and reattach the cup.
Unscrew and reattach the cup.
Empty some solution from the
cup so it is half to 3/4 full.
The air flow is
cutting in an out
The filter is dirty
The power setting need
adjusting
Remove the filter from the base of
the unit and rinse in warm water.
Wait until filter is completely dry
before refitting.
Increase the power on your system.
Power cord not attached
Electricity not turned on
Ensure that the power cord is
pushed in firmly to the base of the
unit and wall socket
Ensure that the power point is on
The Spray Unit
will not turn on
Spray Cup is not tight enough
Too much solution
Nozzle may be blocked
Tighten the solution cup
Empty some solution from the
cup so it is half to 3/4 full
Perform secondary maintenance
The spray
applicator is
leaking
Prongs & groove are not
aligning properly
Pull connection back exposing
the prongs. Ensuring the groove
is facing the top, line up the prongs
to meet the unit. Release the
connection & screw in clockwise.
My hose won’t
screw into the
unit.
Indice
