Target FeedMaster-RF Manuale utente

REV. 03

M 890-00002 rev.09

Feed Scale

TARGET

FeedMaster-RF

User's Manual

FOR CUSTOMER USE

Enter the serial number located on the side

of the controller below for future reference.

Model number:

Serial number:

TARGET FEED MASTER RF

Every effort has been made to ensure that this manual is complete,

accurate and up-to-date. The information contained in it is

however subject to change without notice due to further

developments.

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

Output auger see Augers

Parameters (modification) 12

Password 44

Pause 57

Problems

Alarms 42

Troubleshooting guide 58

Programs

Safety backup see Memory card

Proximity sensors

Location 8

Proxy switch

Activation & operation 48

PSFS-1

Operation & Settings 49

Technical specifications 66

Relay assignment 51–52

Relay box

ID number 52

Relay selection 53

Technical specifications 66

Safety backup see Memory card

Scale

Calibration 56

Current weighing 22

Manual operation 49

Max Batch 48

Settings 48

Status 22

Valve activation 46

Weight's measurement units 46

Schedule see Feed cycles

Serial number 2

Shortcut keys 11, 12

Stick see Memory card

Stop / pause a running cycle 57

Substitution see Blends

Symbols of the manual 6

Technical specifications 66

Time

Feed cycles' start time 37

Time clock outputs

Activation 46

Operation & Settings 41

Relay assignment 53

Time of reset 47

Time settings 29

Transfer

Configuration transfer 67

Transfer error 68

Troubleshooting guide 58

Units

Weight units 46

Valve

Activation 46

Manual opening 49

Weight see also Scale

Weight units 46

Wiring 9

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

Drops

Activating the drops 45

Current drop information 22

Ingredient selection 37

Relay assignment 53

Settings 50

Electrical specifications 66

Empty tolerance 49

Error (transfer) 68

Errors

Alarm 42

Troubleshooting guide 58

Feed bins see Bin

Feed blends see Blends

Feed consumption

History 28

Manual adjustment 27

Mode: /100 birds

Selecting the consumption

mode 46

Settings 37, 38

Mode: Total feed quantity

Selecting the consumption

mode 46

Settings 38

Today's consumption 27

Feed cycles

Abort / pause a running cycle 57

Activation 46

Amount of feed 37

Current ongoing cycle 22

Enable / disable the cycles 37

Feeding days 35

Independent feed cycles 57

Settings 36–38

Start time 37

Feed distribution see Feed cycles

Feed drops see Drops

Feed schedule see Feed cycles

Females see Birds

Flock see Birds

History

Bins' added feed history 26

Bins' consumption history 25

Feed consumption history 28

Mortality history 28

Hot keys 12

Hour see Time

Houses

Activation 45

Houses' feed drops 50

ID numbers 52

Independent feed cycle 57

Ingredients

Distribution see Feed cycles

Ingredient blends see Blends

Mixing ingredients 46

Installation

Controller's main settings 45

Installer password 44

Keys 11

Shortcut keys 12

Manual mode 57

Memory card 67

Mixer

Activation 46

Activation & Settings 46

Relay assignment 53

Mortalities 21

Mounting instructions 9

TARGET FEED MASTER RF rev.09

1. INTRODUCTION ................................................................. 5

1.1 Precautions, Care & Maintenance .................................... 5

1.2 List of Symbols ......................................................... 6

2 SYSTEM OVERVIEW ............................................................ 7

2.1 Description of the Controller........................................ 7

2.2 Typical Application .................................................... 8

3. MOUNTING INSTRUCTIONS ................................................. 9

3.1 Installing the Controller on the Wall .............................. 9

3.2 Connections ............................................................. 9

3.2.1 Controller’s Main Wiring ................................................ 9

3.2.2 Alarm Connection ....................................................... 10

4. USER INTERFACE .............................................................. 11

4.1 Location of the Controls ........................................... 11

4.2 How to Select & Modify the Parameters ..................... 12

4.3 Feed Scale Menus ................................................... 13

5. USING THE CONTROLLER ................................................... 18

5.1 First Installation ...................................................... 18

5.2 Starting a New Flock ............................................... 20

5.3 Monitoring Functions ................................................ 21

5.3.1 Monitoring the Number of Birds .................................... 21

5.3.2 Ongoing Operations .................................................... 22

5.3.3 Bin Management ......................................................... 23

5.3.4 Viewing Today's Feed Consumption ............................. 27

5.3.5 Feed Consumption and Mortality History ........................ 28

5.4 Setting the Time and Date ........................................ 29

5.4.1 Viewing the Day of the Week ...................................... 29

5.5 Feeding Schedule .................................................... 30

5.5.1 Feed Blends ............................................................... 30

5.5.2 Blend Curves ............................................................. 33

5.5.3 Setting Feeding Days .................................................. 35

5.5.4 Setting Feed Cycles .................................................... 36

5.5.5 Feed Curves ............................................................... 39

5.6 Time Clocks ........................................................... 41

TABLE OF CONTENTS

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

5.7 Alarms .................................................................. 42

5.7.1 Alarm Log .................................................................. 42

5.7.2 Acknowledging an Alarm ............................................. 43

5.8. Installation settings .................................................. 44

5.8.1 Password .................................................................. 44

5.8.2 Main Controller Settings .............................................. 45

5.8.3 Scale Settings ............................................................ 48

5.8.4 Drop Settings ............................................................. 50

5.8.5 Relay Assignment ....................................................... 51

5.8.6 Bin Settings ............................................................... 54

5.8.7 Scale Calibration ......................................................... 56

6. MANUAL MODE ............................................................... 57

7. TROUBLESHOOTING GUIDE ................................................ 58

8. INSTALLATION REPORT .................................................... 62

9. TECHNICAL SPECIFICATIONS ............................................. 66

10. MEMORY CARD .............................................................. 67

INDEX ................................................................................. 69

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

Age see Birds

Alarms

Acknowledging an alarm 43

Alarm output wiring 10

Settings 47

Troubleshooting guide 58

Animals see Birds

Augers

Bin augers see Bin

Output auger

Activation 45

Relay assignment 53

Settings 50

Shutoff augers on alarm 47

Status 22

Backup see Memory card

Bin

Activation 45

Adding feed to a bin 23

Backup bin 55

Bin augers' relay assign-

ment 53

Remaining feed & other bin

info 24

Settings 54

Birds

Bird age 22

Males / females

Feed drop selection 50

Number 21

Mortality 21, 28

Number

Posting initial # of bird 20

Posting mortalities 21

Remaining number 21

Starting a new flock 20

Blends

Activation 45

Blend curves

Principle of operation 33

Settings 34

Blends' substitution

Activation 47

Operation & Settings 31

Distribution of the blends 37

Ingredient selection 30

Mixing the ingredients 46

Buttons 11

Shortcut keys 12

Calibration 56

Card

Memory card 67

Clock outputs see Time clock

Clock settings 29

Configuration module see Memory

Card

Connections 9

Consumption see Feed consumption

Controller

Features 7

Location of the controls 11

Mounting instructions 9

Safety backup see Memory card

Serial number 2

Technical specifications 66

Curves

Blend curve 33, 34

Feed curve 39, 40

Cycles see Feed cycles

Date 29

Day

Blends' substitution days 31

Feeding days 35

Setting the time and date 29

Distribution see Feed cycles

INDEX

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

6. Use the up- and down-arrow keys to select the proper type of transfer:

MEMORY CARD CONTROLLER:

To transfer the memory card's content

into the controller, select the "Mem.Card

Ctrl".Once it is selected, simulta-

neously press the +and - buttons to

start the transfer.

CONTROLLER MEMORY CARD:

To save the controller's configuration

into the memory card, select the "Ctrl

Mem.Card " menu. Once it is se-

lected, simultaneously press +and - but-

tons to start the transfer.

7. Once the transfer is over, simultaneously

press and hold the up- and down-arrow

keys for 5 seconds to exit the transfer

menu, then remove the memory card from

the connector as follows:

- Turn off power to the controller;

- Open the controller's cover;

- Remove the card from the connector;

- Close the cover then reapply power to

the controller.

8. Lock the card’s switch ( ) if required.

IMPORTANT:

REMOVE THE

MEMORY CARD

FROM THE

CONNECTOR WHEN

THE TRANSFER

IS OVER!

Mem.Card > Ctrl

+/- to start

Ctrl > Mem. Card

+/- to start

TRANSFER ERROR

The controller will not warn you if the transfer is incorrect.

Respect the following rules to make sure the transfer works properly:

• Make sure the card switch is at the unlocked position before

transferring a configuration on the card.

• Do not move or hold the card while a transfer is ongoing.



TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

1. INTRODUCTION

1.1 Precautions, Care & Maintenance

WARNING: Read and save

these instructions!

Safety may be jeopardized if the equipment is used in a manner not specified by

the manufacturer. Carefully read and keep the following instructions for future

reference.

• Although fuses at the input and outputs of the controller protect its

circuits in case of an overload or overvoltage, we recommend installing

an additional protection device on the controller's supply circuit.

• The room temperature where the controller is located must always remain

between 32 °F and 104 °F (0 °C to 40 °C). For Indoor use only !

• To avoid exposing the controller to harmful gases or excessive humidity,

it is preferable to install it in a corridor.

•Do not spray water on the controller! In order to clean the control, wipe

it with a damp cloth.

Before servicing or cleaning unit, switch power off at

service panel and lock the switch disconnecting means to

prevent power from being switched accidentally. When the

service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to the

service panel.

• The controller should be opened and inspected once a year for mois-

ture. Proper care will extend the life of the control.

IMPORTANT:

Use Grounded Metallic Conduits Only!

The conduit that brings feed into the scale must absolutely be

made of metal and must be grounded in order to prevent static

electricity. A high static electrical charge may cause malfunc-

tion to the controller.

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

1.2 List of Symbols

Warning. Read the following text carefully; it contains

important information which, if ignored, may cause the

controller to operate improperly.

High Voltage. Hazard of electrical shock. Read the

message and follow the instructions carefully.

Pay attention. The following text contains very useful

information.

Double insulation.

Both direct and alternating current

(AC/DC).

Direct current (DC).

Alternating current (AC).

Earth Ground Terminal

Primarily used for functional earth terminals which are

generally associated with test and measurement cir-

cuits. These terminals are not for safety earthing

purposes but provide an earth reference point.

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

10. MEMORY CARD

The memory card is used to create a backup copy of your controller's

configuration. The card is also useful to transfer the configuration

of one controller to another controller of the same type.

The switch at the bottom of the card is used to lock or to unlock

the card ( = locked, = unlocked).

Turn off power each time you open the controller's

enclosure. This prevents accidental exposure to areas

of high voltage.

TO TRANSFER A CONFIGURATION:

1. Turn off power to the controller.

2. Open the latch and lift the

controller's cover.

3. If you are about to copy the

controller's configuration on the

memory card, make sure the

card's switch is at the unlocked

position.

4. Insert the card in the J9 connec-

tor located on the electronic board

inside the controller. Components

of the memory card must face

down as illustrated.

5. Close the cover then reapply power to the controller. The transfer

menu should be shown on screen (if this is not the case, simulta-

neously press the up- and down-arrow keys for 3 seconds to dis-

play this menu).

Electronic

Board

Memory Card

Card Switch

Connector

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

9. TECHNICAL SPECIFICATIONS

Type TARGET FEED MASTER RF

Main supply fuse F1 1A, fast-blow

Mains supply/frequency 115/230V+10% -20%, 20VA, 50/60Hz

14Vdc output 14 Vdc±10%, regulated,100mA max.

14Vdc output fuse F2 1A, fast-blow

Alarm Relay 10mA to 2A, 24 Vac or dc max.

Relay Output 1 5A, 250VAC max.

Housing IP54, plastic casing

Operating temperature 0 to 40°C (32 to 104°F)

Storage temperature -15 to 50°C (32 to 104°F)

Ambient relative humidity max. 95%

Alarm Relay 10mA to 2A, 24 Vac or dc max.

Pollution degree 2

Altitude Up to 2000m

Installation Category: Class II

Type PSFS-1

Input fuse F1 2.5A, slow-blow

Input 120VAC, +10%, -20%, 20VA, 50/60Hz

Output Voltage ±13-22VDC No load

Output Current 1A max, intermittent duty (10sec ON,

30 sec OFF)

Housing IP54, plastic casing

Operating temperature 0 to 40°C

Storage temperature -15 to 50°C

Ambient relative humidity max. 95%

Type TRB-8

Main supply fuse F2 1A, fast-blow

Mains supply/frequency 115/230V+10% -20%, 20VA, 50/60Hz

Relay Output 1-8: 10A Res, 1/2HP 250VAC

Housing IP54, plastic casing

Operating temperature 0 to 40°C

Storage temperature -15 to 50°C

Ambient relative humidity max. 95%

The room temperature where the controller is located must

always remain between 32oand 104oF (0oand 40oC).

For indoor use only.

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

2 SYSTEM OVERVIEW

2.1 Description of the Controller

The

TARGET FEED MASTER RF

controller is an electronic device

which takes in charge the feed weighing and distribution process

in 2 houses. The scale provided with the controller measures feed

with accuracy. Therefore, the user always knows the amount of

feed remaining in each bin.

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

OUTPUT AUGER

FEED LINES

MOTOR

PROXIMITY

SWITCH

(OPTIONAL)

SCALE

WITH VALVE

WEIGHING SYSTEM

WITH VALVE

HOUSE 1

DROP

LOAD CELLS

PROXIMITY

SWITCH

(OPTIONAL)

WEIGHING SYSTEM

WITHOUT VALVE

LOAD CELL

HOUSE 2

RECEIVING

HOPPER

RECEIVING

HOPPER

2.2 Typical Application

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

OUTPUT RELAY OUTPUT RELAY

1234567 NUMBER 1234567 NUMBER

BIN AUGER 1 # _____ TIME CLOCK 5 (1) # _____

BIN AUGER 2 # _____ TIME CLOCK 5 (2) # _____

BIN AUGER 3 # _____ TIME CLOCK 5 (3) # _____

BIN AUGER 4 # _____ TIME CLOCK 5 (4) # _____

BIN AUGER 5 # _____ TIME CLOCK 5 (5) # _____

BIN AUGER 6 # _____ TIME CLOCK 5 (6) # _____

OUTPUT AUGER 1 # _____ TIME CLOCK 5 (7) # _____

OUTPUT AUGER 2 # _____ TIME CLOCK 5 (8) # _____

OUTPUT AUGER 3 # _____ TIME CLOCK 6 (1) # _____

OUTPUT AUGER 4 # _____ TIME CLOCK 6 (2) # _____

MIXER # _____ TIME CLOCK 6 (3) # _____

TIME CLOCK 1 (1) # _____ TIME CLOCK 6 (4) # _____

TIME CLOCK 1 (2) # _____ TIME CLOCK 6 (5) # _____

TIME CLOCK 1 (3) # _____ TIME CLOCK 6 (6) # _____

TIME CLOCK 1 (4) # _____ TIME CLOCK 6 (7) # _____

TIME CLOCK 1 (5) # _____ TIME CLOCK 6 (8) # _____

TIME CLOCK 1 (6) # _____ TIME CLOCK 7 (1) # _____

TIME CLOCK 1 (7) # _____ TIME CLOCK 7 (2) # _____

TIME CLOCK 1 (8) # _____ TIME CLOCK 7 (3) # _____

TIME CLOCK 2 (1) # _____ TIME CLOCK 7 (4) # _____

TIME CLOCK 2 (2) # _____ TIME CLOCK 7 (5) # _____

TIME CLOCK 2 (3) # _____ TIME CLOCK 7 (6) # _____

TIME CLOCK 2 (4) # _____ TIME CLOCK 7 (7) # _____

TIME CLOCK 2 (5) # _____ TIME CLOCK 7 (8) # _____

TIME CLOCK 2 (6) # _____ TIME CLOCK 8 (1) # _____

TIME CLOCK 2 (7) # _____ TIME CLOCK 8 (2) # _____

TIME CLOCK 2 (8) # _____ TIME CLOCK 8 (3) # _____

TIME CLOCK 3 (1) # _____ TIME CLOCK 8 (4) # _____

TIME CLOCK 3 (2) # _____ TIME CLOCK 8 (5) # _____

TIME CLOCK 3 (3) # _____ TIME CLOCK 8 (6) # _____

TIME CLOCK 3 (4) # _____ TIME CLOCK 8 (7) # _____

TIME CLOCK 3 (5) # _____ TIME CLOCK 8 (8) # _____

TIME CLOCK 3 (6) # _____ DROP 1 # _____

TIME CLOCK 3 (7) # _____ DROP 2 # _____

TIME CLOCK 3 (8) # _____ DROP 3 # _____

TIME CLOCK 4 (1) # _____ DROP 4 # _____

TIME CLOCK 4 (2) # _____ DROP 5 # _____

TIME CLOCK 4 (3) # _____ DROP 6 # _____

TIME CLOCK 4 (4) # _____ DROP 7 # _____

TIME CLOCK 4 (5) # _____ DROP 8 # _____

TIME CLOCK 4 (6) # _____ DROP 9 # _____

TIME CLOCK 4 (7) # _____ DROP 10 # _____

TIME CLOCK 4 (8) # _____ DROP 11 # _____

TIME CLOCK 5 (1) # _____ DROP 12 # _____

TIME CLOCK 5 (2) # _____ DROP 13 # _____

TIME CLOCK 5 (3) # _____ DROP 14 # _____

TIME CLOCK 5 (4) # _____ DROP 15 # _____

TIME CLOCK 5 (5) # _____ DROP 16 # _____

TIME CLOCK 5 (6) # _____ DROP 17 # _____

TIME CLOCK 5 (7) # _____ DROP 18 # _____

TIME CLOCK 5 (8) # _____ DROP 19 # _____

DROP 20 # _____

RELAY MODULE'S # ID RELAY MODULE'S # ID

Relay Assignment Table

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

DROP 1

DROP 2

DROP 3

DROP 4

DROP 5

DROP 6

DROP 7

DROP 8

DROP 9

DROP 10

DROP 11

DROP 12

DROP 13

DROP 14

DROP 15

DROP 16

DROP 17

DROP 18

DROP 19

DROP 20

DROP SETTINGS (SEC. 5.8.4)

OUTPUT

AUGER #

(1 TO 4)

1234

HOUSE #

(1 OR 2)

1 2

RUN TIME

(Min:Sec)

Min:

ANIMAL

(MALE OR

FEMALE)

M F

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

3. MOUNTING INSTRUCTIONS

3.1 Installing the Controller on the Wall

Open the latch and lift the cover. Remove the black caps located

on each of the four mounting holes. Mount the enclosure on the

wall using four screws. Be sure the electrical knockouts are at

the bottom of the enclosure in order to prevent water from enter-

ing the controller. Insert the screws in the mounting holes and

tighten. Fasten the four black caps provided with the controller

onto the four mounting holes. The enclosure must be mounted in a

location that will allow the cover to be completely opened right up

against the wall.

3.2 Connections

3.2.1 Controller’s Main Wiring

Refer to the wiring diagram enclosed with this user's manual to

connect the controller. Use the electrical knockouts provided at

the bottom of the enclosure. Do not make additional holes in the

enclosure, particularly on the side of the enclosure when using a

computer communication module.



All wiring must be done by an authorized electrician and

must comply with applicable codes, laws and regula-

tions. Be sure power is off before doing any wiring to

avoid electrical shocks and equipment damage.



Do not install rigid conduit into electrical knockouts.

Only nylon cable glands are permitted for cable or wire

fastening.



The controller has no power-on switch. An external

switch or circuit breaker shall be included in the

building installation to interrupt power to L and N

electric power lines. It shall be in close proximity to the

equipment and within easy reach of the operator. It

shall be marked as the disconnecting device for the

equipment.

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

3.2.2 Alarm Connection

There are two types of alarms on the market. One type

activates when current is cut off at its input, whereas

the other activates when current is supplied at its input.

For an alarm of the first type, use the NC terminal as

shown on the wiring diagram. For an alarm of the sec-

ond type, use the NO terminal.

TARGET FEED MASTER RF

TARGET FEED MASTER RF rev.09

# of bins

# of houses

# of output augers

# of blends

# drops

# feed cycles

# of time clocks

Use Mixer ?

Mixing time

Mix each batch

Units

Scale with valve ?

Feed qty consumption

Dump Separately?

Substitution?

Time of reset

Shutoff augers on

INSTALLATION SETTINGS (SEC. 5.8.2)

21 3

YES

LBS

(1 to 20)

Min:

Time clock 1

Time clock 2

Time clock 3

Time clock 4

Time clock 5

Time clock 6

DEVICES ON TIME CLOCKS :

Time clock 7

Time clock 8

run time alarms?

YES

Total

/100 birds

NOYES

Indice

Altri manuali Target Scala

Target

Target FeedMaster Manuale utente

Manuali Scala popolari di altre marche

AWS

AWS ZEO-50 Manuale utente

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

Rice Lake

Rice Lake MSI-4260 IS Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente