Targetti BULLETTO MINI Manuale utente
BULLETTO MINI
BULLETTO
Product Code: BLMRP-
BLTRP-
:$51,1*
To ensure a maximum efficient use
of the product, read the instructions
before proceeding installment.
This fixture must be installed by a licensed and
qualified electrician. The installer must comply with
NEC and local building codes when installing the
fixture
Electrical current can cause painful shock, serious
injury, or even death. Make sure you turn off
the power supply, ground fixture(s), and make
sure all electrical connections are correct and
secured
For use in IP67 installations.
Keep the label of the original packaging if any
eventual future claims are needed
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
- Email:[email protected] - www.targetti.us - 04.10.20 - Page 1 of 9
Note: Remote Class II 110-277VAC to 24VDC electronic
power supply and 120VAC to 24VDC power supply.
WIRING FIXTURE TO LINE VOLTAGE WILL DAMAGE
FIXTURE AND VOID WARRANTY.
5 ft
3.86" 2.64"
6.89"
5 ft
6.30"
6.69"
1.57"
1.97"
6.50"
1.37 lbs
1.01 lbs
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
- Email:[email protected] - www.targetti.us - 04.10.20 - Page 2 of 9
Table of Contents
Packaging Contents
Mounting Position
Mounting Installation
Accessories Installation
Maintenance
Support Page
Pg.2
Pg.3-6
Pg.7-8
Pg.9
Pg.10
Pg.2
The Bulletto fixture offers two types of
mounting brackets for various
installation options. The rotational
bracket (cod.1E3786 & 1E3804) is
used for mounting the fixture on a flat
surface. Rotational bracket can also
be used to mount the fixture on a
pole, see page 4 for further details.
The second type of mounting bracket
is the earth spike mounting bracket
(cod. 1E3785 & 1E3803). The
mounting bracket is used for mounting
in soil for outdoor application.
Mounting Brackets
COD. 1E3786
COD. 1E3804
COD. 1E3785
COD. 1E3803
Bracket Assembly
Mounting Installation
Both mounting brackets have the same
assembly instructions for both the
Bulletto and the Bulletto Mini. Installer
will first remove the lock nut that is
attached to the fixture. Once removed,
insert the fixture's cable and bottom end
through mounting bracket hole until the
fixture bottom is flat with the mounting
bracket. Then attach the lock ring back
on the fixture's bottom threading to
secure the fixture with the mounting
bracket. Be sure to properly tighten the
lock nut to secure the fixture on the
mounting bracket.
Once the mounting bracket is assembled,
using the measurements provided, mark
the distance on the designated mounting
surface and drill holes to prepare the
proper mounting fasteners. Installer is
responsible for providing the correct
mounting fasteners based on the surface
type. Installer will use the designated
mounting screws and secure the mounting
bracket to the surface. Installer must
comply with local building code when
installing.
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
- Email:[email protected] - www.targetti.us - 04.10.20 - Page 3 of 9
Lock
1
2
3
24 mm
3.54"
( X )
0.33"
0.73"
X
4.25"
1.18"
Non incluso
Not included
1
Not included
Rotational Bracket Mounting
2
The rotational bracket is also used
for pole mounting installation. For
pole mounting, installer will insert
the belt through the slotted
opening of the assembled
rotational bracket with the fixture
attached on the bracket. Up to
four fixtures max can be
attached on one belt. Once the
desired amount of fixtures is on
the belt, wrap the belt around the
pole and secure the belt tightly
with the belt buckle.
To mount the earth spike bracket,
first be sure that the proper space
and depth for the earth spike to be
mounted is cleared. Once all is
cleared, insert the earth spike with
the attached fixture into the
ground. Be sure that the earth
spike is leveled and secured to the
ground.
Mounting Installation
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
- Email:[email protected] - www.targetti.us - 04.10.20 - Page 4 of 9
7.17" 1.97"
COD. 1E3785
COD. 1E3803 Lock
24 mm
Ø 140mm MIN.
Rotation Bracket Mounting
Earthspike Bracket Mounting
The Bulletto and the Bulletto mini fixture are powered by a 24VDC constant voltage power supply that is
installed remotely. This installation must be done by a qualified electrician that complies with NEC
and local building code. CAUTION: DO NOT CONNECT FIXTURE TO LIVE VOLTAGE! THIS WILL
DAMAGE THE FIXTURE AND VOID THE WARRANTY!
Fixture is powered with a class 2, 3 wire cable for low voltage application. Installer will run class 2 cable
rated based on the location of application from the output power feed to the driver. Cable length (A) and
gauge (B) will be determined based on installer that complies with NEC, local building code, and voltage
drop threshold percentage of <3%.
i) As a rule of thumb, we recommend installers a max distance of 50 feet with 12 gauge wiring with a
full load 96W fixture system.
Installer will wire the fixture(s) with the daisy chain connection as shown in the diagram below. Installer
must wire the fixture(s) system equal or under the max fixture allowed per power supply. See chart for
reference of max load. Overloading the fixture with the driver will damage the fixture and will void
the fixture and driver warranty.
Fixture Electrical Wiring Instructions
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
- Email:[email protected] - www.targetti.us - 04.10.20 - Page 5 of 9
Red
Green
Black
+
-
Output wire color code
IN
Daisy Chain
Connection
OUT OUT
MAX FIXTURES PER DRIVER
Fixture
Wattage
Driver Wattage
40W 60W 96W 90W 2X90W 3X90W 100W 2X100
Bulletto Mini 8W 4 6 9 9 18 27 10 20
Bulletto 10W 3 4 7 7 14 21 8 16
Bulletto 12W 2 4 6 6 12 18 6 13
IN
120-2777VAC
Input Power
0-10V
Dimming
Last
Connection
24VDC
Output Power
ADJUSTMENT
The Bulletto and Bulletto mini fixture has
a wide range of motion to aim practically
anywhere from where it mounted. The
fixture has a 360 degree rotational
freedom and a 180 degree pivotal range
of motion. To change the rotational
angle, unlock the lock nut that holds the
fixture to the mounting bracket and
adjust the rotation to the desired setting.
Once adjusted, secure the lock ring back
to hold the fixture in place and tighten to
secure.
To adjust the pivot angle of the fixture,
use a 3mm hex Allen key (supplied by
installer) to loosen the lock screw. This
will allow the fixture to move freely to
position. Once the fixture is adjusted,
use the same Allen key to lock the
position in place.
Mounting Installation
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
- Email:[email protected] - www.targetti.us - 04.10.20 - Page 6 of 9
360°
360°
Lock
3mm
90°
90°
24
1
2
Accessories Installation
1. The Bulletto and Bulletto mini fixture has a
wide range of accessories to customize.
To change the accessories, first remove
the fixture asymmetric screen by loosening
the 1.5 mm hex screw using a Allen key
(not included). Once the hex screws is
removed, remove the asymmetric screen
to access the inside to add the filter that
the user prefers.
2. Unscrew the head cap to access the
internal optical components inside (a).
Remove the cap (b) and the lens (c) to
access the optical reflector and filter holder
(d). Remove the optical reflector from the
filter holder (e) to switch the optic type.
Then choose the desired filter(s) you wish
to add in the filter holder. The filter holder
can hold up to three max filters per fixture
(g). For the blade of light filter, pick the
desired position you want to add the blade
of light and attach the filter in the same
order as any other filter. See chart below
for different types of filters available.
3. Once the filter(s) have been set, put back
the fixture pieces together starting in
reverse order with the filter holder (a), the
lens (b), and then the cap (c) and screw
the cap back on tight clockwise (d). Then
reattach the asymmetric screen back on
and secure it with the 1.5 mm Allen key (e).
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
- Email:[email protected] - www.targetti.us - 04.10.20 - Page 7 of 9
11,5mm
Lock
BLM COD. 1E3787 / 1E3788
BLT COD. 1E3805 / 1E3806
Asymmetric screen
a
b
c
d
e
SP
d
b
a
c
ANTI-GLARE LOUVER
COD. 1E3791 / 1E3792
f
g
NFL / FL / WFL
1E3793
BLM
1E3798
1E3799
1E3800
1E3801
1E3802
CHROMATIC FILTERS
BLT
1E3794
1E3795
1E3796
1E3797
COD.
COD.
COD.
COD.
COD.
1E3789
BLM
1E3790
ELLIPTICAL FILTER
BLT
COD.
Luminous
effect
3
1,5mm
Lock
e
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
Maintenance
This fixture was designed and manufactured for a durable,
long lasting use with minimum care. To ensure the
maximum lifespan of this product, we encourage our
customer to provide a quality visual inspection of the fixture
every six months.
If there are any visible sign of issues (i.e moisture or dust)
during the inspection, please clean any of the dust or
moisture with a soft cloth and check to make sure that any
of the fixtures are still operating normally. If there are any
issues regarding the fixture please contact us as we will
assist the situation at hand.
Targetti USA - A Targetti Group Company - 750-A W 17th St. Costa Mesa, CA 92627 - Phone (714) 513-1991
- Email:[email protected] - www.targetti.us - 04.10.20 - Page 9 of 9
Support
Any questions, problems, or comments you have please
feel free to contact our Customer Service department
during our business hours Monday-Friday 8am-5pm via:
Email: usaorders@targetti.com
Phone: (714) 513-1991
Visit our website: http://www.targetti.us
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Targetti Illuminazione del paesaggio
Manuali Illuminazione del paesaggio popolari di altre marche
Cooper Lighting
Cooper Lighting MCGRAW-EDISON WBG Manuale utente
Cooper Lighting
Cooper Lighting Invue 42 - 175W Manuale utente
Saxby Lighting
Saxby Lighting Islay 68784 Manuale
LIGMAN
LIGMAN EU-10016-3 Manuale utente
Cooper Lighting
Cooper Lighting McGraw-Edison ZD Credenza Manuale utente
LIGMAN
LIGMAN KI-60475 Manuale utente
