TASKING iSYSTEM ST SPC58 Istruzioni per l’uso
ST SPC58 H Line Emulation Adapter
Hardware User Manual
V1.8, November 2023
isystem.com/start
General safety instructions
Please read the following safety precautions carefully before putting this device to use to avoid
any personal injuries, damage to the instrument, or to the target system. Use this instrument
only for its intended purpose as specified by this manual to prevent potential hazards.
Use included power cord and power supply
The enclosed power supply has been approved for use by iSYSTEM. Please contact iSYSTEM if
you need to consider an alternative power.
Use grounding wire
Prior to applying power to either the BlueBox or the target, connect the device and the target sys-
tem together with the included grounding wire. This is to avoid potential damage caused by any
voltage difference between the device and the target system.
Use proper overvoltage protection
Ensure proper protection to avoid exposing the BlueBox device or the operator to overvoltage
surges (e.g. caused by thunderstorm, mains power).
Do not operate without cover
Do not operate the device with cover removed.
Avoid circuit and wire exposure
Do not touch exposed components or wires when the device is powered.
Do not operate with suspected damage
If you suspect damage may have occurred, the BlueBox device must be inspected by qualified
service personnel before further operation.
Do not operate the device outside its rated supply voltage or environ-
mental range
Consult with iSYSTEM before using equipment outside of the parameters provided in this
manual.
This symbol is used within the manual to highlight further safety notices.
Contents
Introduction .......................................................................................................................................... 4
Package content ................................................................................................................................ 5
Adaptation packages content .............................................................................................................. 6
Operation ............................................................................................................................................... 7
Adaptation setup ..................................................................................................................................... 8
Screws ....................................................................................................................................................................................................................................10
Configuration .......................................................................................................................................... 11
Connectors .............................................................................................................................................. 15
Conversion board configuration ......................................................................................................... 16
Power supply package ......................................................................................................................... 25
Standalone operation ........................................................................................................................... 26
Mechanical information ............................................................................................................. 27
BGA Assembly ........................................................................................................................................ 29
NQ Pack Assembly ................................................................................................................................ 31
Accessories ......................................................................................................................................... 32
User Notes .......................................................................................................................................... 33
Introduction
ST SPC58 (Chorus) H Line Emulation Adapter primary use case is providing Nexus trace func-
tionality for the SPC58 H Line devices in the:
·
144-pin
·
176-pin
·
302-pin
where Nexus trace port is not available.
The Emulation Adapter might differ in some peripherals from the target device; there-
fore, the device datasheet should be checked.
Alternative use case is a Standalone operation, where you can start developing and testing the
application while his target may not be available yet.
ST SPC58 H Line Emulation Adapter is based on the "superset" SPC58NH92C5 device in the
BGA386 package on which the Nexus trace port is also exposed and available (P1 connector).
It’s a "superset" device with 10MB program flash and can emulate all ST SPC58 H Line devices
in smaller packages.
Complete Emulation Adapter is split into individual parts which makes it flexible when support
for different target packages is required. A typical setup in conjunction with the target contains:
·
IEA-SPC58NH (Microcontroller part)
·
Conversion board
·
Solder part
More information about our products on www.isystem.com or via sales@isystem.com.
Package content
ST SPC58 H Line Emulation Adapter is delivered with all components required for a standalone
operation. Adaptation package for the Target board adaptation and the Power adapter must be
ordered separately.
ST SPC58 H Line
Emulation Adapter
Power supply package
Power converter
Power adapter
Ordering code:
IEA-SPC58NH
Ordering code:
IEA-PS
Ordering code:
IT9V-PS
GND Wire
Crystal 20 MHz
Ordering code:
BB-WIRE
Adaptation packages content
Conversion boards connect between the Emulation Adapter and the matching Solder part which
is being soldered on the Target side.
Pin number
Conversion board
Type
Extender
Solder part
144
IEA-SPC58NH-TQ144
Fixed
IA144TQ-SOLDER
176
IEA-SPC58NH-TQ176
Fixed
IA176TQ-SOLDER
302
IEA-SPC58NH-BGA302
Fixed (BGA)
IA302LFBGA-EXTENDER
IA302LFBGA-SOLDER
BGA Adaptation: The Target can have electronic components placed around the Micro-
controller within the Emulation Adapter (EA) "ground floor", which impede connecting
the EA to the Target. In such cases the distance of the EA from the Target can be op-
tionally increased in steps of 3.25 mm by inserting the optional Extender. Not more
than two Extenders should be used since every connector affects signal integrity.
·
With no Extender the lowest point of the EA is approx. 4.35 mm away from the Tar-
get.
·
With one Extender the lowest point of the EA is approx. 7.6 mm away from the Tar-
get.
·
With two Extenders the lowest point of the EA is approx. 10.85 mm away from the
Target.
Note that by adding the Extender or two, makes the whole setup less robust. Use cau-
tion with Extenders to prevent breaking of the hardware setup or just part of it.
Fixed Adaptation
The adaptation is elivered with a slot screw, which can be used to achieve a more solid and
stable fixing of the Conversion board and the Solder part.
Conversion board
Solder part
BGA Adaptation
Conversion board
Extender (optional)
Solder part
Adaptation setup
Emulation Adapter offers the following adaption setups.
Fixed Adaptation
BGA Adaptation
Screws
Slot screw
The Slot screw (30mm) is used to fix the Conversion board to the Solder part. The setup be-
comes mechanically more robust.Screw the Conversion board to the Solder part first, before the
Emulation Adapter is attached on top and watch out not to break out the Solder part, e.g., if you
accidentally hit the Emulation Adapter from the side.
Short Hexagon socket screw
Short Hexagon socket screw, which comes with the Solder part, is not applicable with this Emu-
lation Adapter setup.
Indice
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
