Taymor Concierge 300 Manuale utente
CONCIERGE 300
PROFESSIONAL SERIES
ELECTRONIC DEADBOLT
USER GUIDE
REV. 07/15
IMPORTANT: Before first use,
please read page 20 in the User
Guide for important instructions.
Concierge 300 install booklet ENGLISHnew.indd 1 7/15/15 9:12 AM
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
Concierge 300 install booklet ENGLISHnew.indd 2 7/15/15 9:12 AM
IMPORTANT SAFETY INFORMATION 1
TOOLS NEEDED FOR NEW INSTALLATION 2
COMPONENTS OF ELECTRONIC KEYPAD DEADBOLT 3
DOOR PREPARATION 4 - 8
INSTALLATION 9 - 20
OVERVIEW OF FUNCTIONS 21
CODES INFORMATION 22
PROGRAMMING
1. CHANGE PROGRAMMING CODE 23
2. ADD NEW USER ENTRY CODE 24
3. ADD ONE OR MORE SINGLE-USE USER ENTRY CODES 25
4. DELETE EXISTING USER ENTRY CODES 26
5. DELETE ALL EXISTING USER ENTRY CODES AT ONCE 27
6. TEMPORARILY DISABLE ALL USER CODES (VACATION MODE) 28
7. DISABLE BUTTON SOUND (MUTE MODE) 29
8. SET UP AUTO-LOCK TIME DELAY 30
9. TURN ON/OFF THE AUTO-LOCK FUNCTION 31
10. RESTORE FACTORY SETTING 32
OPERATION
1. LOCK OPERATION 33
2. SECURITY MODE 34
TROUBLESHOOTING GUIDE 35 - 38
INFORMATION PAGE 39
WARRANTY 40
CONTENTS
Concierge 300 install booklet ENGLISHnew.indd 3 7/15/15 9:12 AM
1
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
IMPORTANT SAFETY INFORMATION
! WARNING
1. Do not use any abrasives or any chemical products containing any
substance of alcohol, benzene, hydrochloric acid or nitric acid, and
avoid sharp or scratching objects to clean this lockset.
2. Do not let any water or liquid into lockset during installation process.
Note: Electronic mechanisms may be sensitive in cold, harsh conditions
particularly if the environment is also humid. In these conditions, the
manual key may be the most convenient method to operate the lock.
! IMPORTANT SAFETY INSTRUCTION
1. Do not attempt to disassemble any internal components of the lock-
set personally. You may run the risk of voiding the limited warranty.
2. Do not drop or hit the lockset.
3. Do not use sharp objects to press key buttons.
4. Always create a backup of information you want to keep (such as pro-
gramming code and user entry codes). Please use the last page of
this booklet as your reference.
5. Please change the programming code before operating this lockset.
! CARE AND MAINTENANCE
The following care instructions should be followed:
1. Remove locks, or do not install locks, prior to painting your door.
2. Periodically clean with mild soap and a soft cloth only.
Concierge 300 install booklet ENGLISHnew.indd 4 7/15/15 9:12 AM
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
2
• PENCIL
• CHISEL
• TAPE MEASURE
• HAMMER
• PHILLIPS SCREWDRIVER
• 1” (25 mm) & 1/8” (3 mm) DRILL BITS
• 2-1/8” (54 mm) OR 1-1/2” (38 mm) HOLE BORING KIT
• POWER DRILL
• 2” (51 mm) 6D COMMON NAIL
• 4 - AA ALKALINE BATTERIES
TOOLS NEEDED FOR NEW INSTALLATION
Concierge 300 install booklet ENGLISHnew.indd 5 7/15/15 9:12 AM
3
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
COMPONENTS OF
ELECTRONIC
KEYPAD DEADBOLT
B
D
E
L
N
F
G
H
I
J
K
CA
R
Q
M
T
S
P
O
A. Key (2)
B. Exterior Assembly
C. Cylinder
D. Power Strip
E. Cylinder Torque Blade
F. Mounting Plate
G. 2-1/8” (54 mm) Mounting Bolt (2)
H. Interior Assembly
I. 13/16” (20 mm) Screw (1)
J. 5/16” (7.8 mm) Screw (2)
K. Interior Cover
L. Latch (Square or radius faceplate
or drive-in)
M. Drive-in Collar (Optional)
N. 3/4” (19 mm) Wood Screw (4)
O. Strike Plate
P. 3” (76 mm) Wood Screw (2)
Q. Reinforced Strike Plate
R. Dust Box
S. Mortise Back Plate (Optional)
T. Square or Radius Mortise Face
Plate (Optional)
Concierge 300 install booklet ENGLISHnew.indd 6 7/15/15 9:12 AM
TEMPLATE
CENTERLINE
MARK DOOR EDGE APPROXIMATELY
3” TO 6” (75 mm TO 150 mm) ABOVE
THE ENTRY KNOB OR LEVER
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
4
DOOR PREPARATION
1 MARK DOOR WITH TEMPLATE (ATTACHED SEPARATELY)
Note: If replacing an existing lock or installing in a pre-drilled door,
begin with page 8.
a. Use TEMPLATE to mark centerline on door for deadbolt about
3” to 6” (75 mm to 150 mm) above the existing knob or lever.
b. Stand so door swings towards you. Align template on centerline
and fold template as shown.
Concierge 300 install booklet ENGLISHnew.indd 7 7/15/15 9:12 AM
5
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
DOOR PREPARATION
2 MARK AND DRILL PILOT HOLES
Select backset. Mark and drill pilot holes as shown.
CENTERLINE
BACKSET
DRILL 1/8” (3 mm) PILOT HOLE
1”
(25 mm)
2-1/8” OR 1-1/2”
(54 mm) (38 mm)
DRILL 1/8” (3 mm) PILOT HOLE
Concierge 300 install booklet ENGLISHnew.indd 8 7/15/15 9:12 AM
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
6
DOOR PREPARATION
3.1 DRILL HOLES
a. Drill a 2-1/8” (54 mm) or 1-1/2” (38 mm) hole on the door face
from both sides to avoid wood splitting.
b. Use a 2” (51 mm) 6d common nail and press it from inside the
2-1/8” (54 mm) or 1-1/2” (38 mm) hole through the pilot hole to
mark centerlines on jamb exactly opposite center of deadbolt
latch hole.
1-1/2”
(38 mm)
OR
2-1/8”
(54 mm)
Concierge 300 install booklet ENGLISHnew.indd 9 7/15/15 9:12 AM
7
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
DOOR PREPARATION
3.2 DRILL HOLES
c. Drill a 1” (25 mm) hole in the door edge for the latch.
d. Use faceplate as a pattern for mortise and pilot holes.
Chisel 5/32” (4 mm) deep. Faceplate should fit flush.
Note: For drive-in latch, simply insert latch.
e. Install as shown for appropriate latch type. Ensure bevel
faces door jamb.
CHISEL 5/32”
(4 mm) DEEP
1”
(25 mm)
FACEPLATE
c.
d.
OUTLINE
Concierge 300 install booklet ENGLISHnew.indd 10 7/15/15 9:12 AM
Indice
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
