TE Connectivity 1752786-1 Manuale utente

Instruction Sheet

1 of 6

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

408-8958

19 JUL 17 Rev C

Figure 1

1. INTRODUCTION

This instruction sheet covers application, inspection and maintenance procedures for Hydraulic Crimping Head

PN 1752786-1 shown in Figure 1.

The crimping head accepts interchangeable die sets for a variety of terminals and splices for large wire sizes -

4/0 through 1000 MCM range. Refer to the instructions packaged with the specific die sets for compatible

products, wire ranges, strip dimensions, and application procedures.

This crimping head is designed for use with Foot Hydraulic Pump PN 1583659-1, Hand Hydraulic Pump PN

1583661-1, or Electric Hydraulic Pumps; PN 1804700-1 (115 VAC) and PN 1804700-2 (220 VAC).

Warning: To avoid personal injury and potential damage to the crimp head, TE Connectivity (TE) requires the

crimp head to operate at 9,800 to 10,200 PSI [676 to 703 bar]. TE recommends using 10,000 PSI [689 bar] TE

Hydraulic Pumps as other manufacturers’ pumps may apply insufficient pressure (resulting in an inadequate

crimp) or excessive pressure (resulting in failure of the head). Additionally, the TE pump must be used to

maintain CE certification; if using other manufacturers’ pumps, the user is responsible for self-certification.

Read these instructions, and all applicable references before inserting any die set assemblies and crimping any

terminals or splices.

NOTE

Dimensions in this instruction sheet are in millimeters [with inches in brackets]. Illustrations and figures are for reference only

and are not drawn to scale.

Reasons for reissue of this Instruction Sheet are provided in Section 9; REVISION SUMMARY

Hydraulic Crimping

Head, PN 1752786-1

ORIGINAL INSTRUCTIONS

408-8958

Rev C

2 of 6

2. DESCRIPTION

Main components of this crimping head include a “C”-Head, which houses the stationary die, a cylinder which

contains the hydraulic chamber, a piston (ram) which holds and controls the moving die, and a quick-

disconnect coupling (cylinder half) which mates with the coupling on the hose to release or supply pressure. A

dust cap covers the quick-disconnect coupling.

3. CRIMPING HEAD INSTALLATION

DANGER

Verify that the hydraulic pressure to hose or handle control is released and that power supply is disconnected from electric

power unit, if applicable.

CAUTION

Prior to installing the head, verify that the pump and hose being used are working properly, and are adjusted to and rated at

68948 kPa [10,000 psi]. An incorrectly adjusted or rated pump/hose could result in severe tooling damage, as well as

personal injury.

1. Remove protective dust caps from both quick connect/disconnect couplers.

2. Thoroughly clean the coupling on the pump/hose and the coupling on the crimping head.

3. Mate both quick-disconnect couplers and tighten the collar of the coupler assembly on the crimping

head (see Figure 1).

CAUTION

Oil flow must be unobstructed between power unit and crimping head. Verify that all couplers are fully mated and tightened.

NOTE

If crimping head must be removed after being in production, pressure must be released in the hydraulic system before head is

removed. If using Electric Hydraulic Power Unit 1804700-1 or 2, disconnect power unit from power supply. When using

Hydraulic Foot Pump PN 1583659-1 or Hydraulic Hand Pump PN 1583661-1, depress the pressure release pedal to release

pressure.

4. DIE INSTALLATION AND REMOVAL (FIGURE 2)

DANGER

To avoid personal injury, avoid accidently depressing foot switch or handle control of power unit when changing dies.

CAUTION

Operating the crimping head WITHOUT the dies installed will damage the “C”-Head or ram.

Installation

1. Back out the set screws in the crimping head and ram (the ram must be raised slightly to gain access

to the set screw).

2. Insert the dies into the crimping head and the ram, ensuring the “flats”of the die shanks are facing the

set screws. Tighten the set screws.

3. Activate the power unit and slowly close the dies to verify proper alignment.

4. Complete the cycle and allow the ram to return to the “DOWN” position.

Removal

DANGER

To avoid personal injury, avoid accidently depressing foot switch or handle control of power unit when changing dies.

CAUTION

Operating the crimping head WITHOUT the dies installed will damage the “C”-Head or ram.

1. Back out the set screw in the crimping head and remove the stationary die.

2. Raise the ram enough to expose the set screw and back it out until the moving die can be removed.

408-8958

Rev C

3 of 6

Figure 2

5. CRIMPING PROCEDURE

The following procedure provides only general information concerning crimping. Refer to instructional material

packaged with the dies and power unit for more detailed information including wire stripping dimensions and

how to position terminals or splices in the dies.

CAUTION

Never operate the power unit without having a crimping head attached to the handle control or crimping head coupling.

1. Insert a terminal or splice in the stationary die in accordance with instructions packaged with the dies.

2. Activate the power unit to advance the dies and hold terminal or splice in place.

3. Insert the stripped wire into the terminal or splice.

4. Activate the power unit to complete the crimp.

6. INSPECTION AND MAINTENANCE

DANGER

Verify hydraulic pressure is released and power supply is disconnected before following inspection and maintenance

procedures, unless otherwise specified in the procedure.

Each crimping head is assembled and inspected before shipment. TE Connectivity recommends that the

crimping head be inspected immediately upon its arrival at the facility of use, and at regularly scheduled

intervals to ensure the head has not been damaged during handling and use. Frequency of inspection

depends upon the following: care, amount of use, and handling of the head; type and size of products crimped;

degree of operator skill; and environmental conditions.

408-8958

Rev C

4 of 6

Visual Inspection

Refer to Figures 3 and 5; proceed as follows:

1. Inspect the assembled crimping head for nicks, scratches, cracks, and excessive wear, especially

where sliding contact occurs.

2. Inspect for cracks particularly at the corners of the “C”-Head and around the top of the cylinder.

NOTE

Once per year, or every 7,500 cycles (whichever comes first), the hydraulic head should be returned to TE for magnetic

particle inspection. Additionally, inspect and service the head every month or 1,000 cycles.

Figure 3

Cleaning

1. Remove accumulations of dirt and grease on the crimping head; especially in areas where dies are

installed and terminals are crimped.

2. Clean the entire head frequently with a clean, lint-free cloth.

Crimping Head Check-Out Procedure

If the ram fails to retract after completion of a crimping cycle, the cause may be in the crimping head. To

determine whether the trouble is in the crimping head or not, release pressure in the power unit.

If the ram retracts, the trouble is not in the crimping head.

If ram does not retract, refer to paragraph 7. REPLACEMENT and REPAIR

408-8958

Rev C

5 of 6

7. REPLACEMENT AND REPAIR

Customer-replaceable parts are listed in Figure 4. A complete inventory should be stocked and controlled to

prevent lost time when replacement of parts is necessary. Order parts through your TE representative or call

1-800-526-5142, or send a facsimile of your purchase order to 1-717-986-7605, or write, or return the entire

tool for evaluation and repair, with a written description of the problem to:

CUSTOMER SERVICE (38-35)

TE CONNECTIVITY CORPORATION

P.O. BOX 3608

HARRISBURG, PA 17105-3608

Tools may also be returned for evaluation and repair. For tool repair service, contact a TE representative at

1-800-526-5136.

Item

Number

Part Number

Description

Quantity

Per Head

21013-4

Screw, Socket Head, Self-Locking, 1/4-20 UNC x 9.52 mm [.375 in] Long

311470-1

Coupler, Quick-Disconnect, Cylinder Half

Figure 4

408-8958

Rev C

6 of 6

8. TROUBLESHOOTING

Part

Inspection and Problem

Possible Solution

“C”-Head

Inspect for cracks, gouges, nicks, or galling on the “C”-Head

or where the “C”-Head contacts dies

Return tool for repair (see Section 7)

Check to see if the upper die retaining pin does not hold the

stationary die in place

Return tool for repair (see Section 7)

Check to see if the upper die release button sticks (it should

normally move in and out easily when moderate pressure is

applied)

Return tool for repair (see Section 7)

Cylinder

Inspect for evidence of cracks, gouges, nicks, or galling

If there are cracks, return the tool for repair (see

Section 7)

For traces of gouges, nicks, or galling: remove

any sharp edges using a fine emery cloth

Inspect for oil leaks between the cylinder and coupling

For oil leaks and a sticky coupling, tighten or

replace the coupling

Check to see if the coupling sticks to the cylinder (it should

normally turn on and off freely when moderate pressure is

applied with a wrench)

Quick-Disconnect

Coupling

The coupling mates hard or will not mate or release, or it

leaks oil, or it sticks at the hose connection

Replace coupling

Ram

Inspect the ram in the Power “ON” (ram advanced) position

for evidence of galling, cracks, or oil leaks between the ram

and the cylinder

If there are cracks or leaks, return the tool for

repair (see Section 7)

If there is galling, remove any sharp edges

using a fine emery cloth

Check to see if the lower die retaining pin does not hold the

moving die in place

Return tool for repair (see Section 7)

Check to see if the lower die release button sticks (it should

normally move in and out easily when moderate pressure is

applied)

Return tool for repair (see Section 7)

Inspect the ram in the Power “OFF” (ram retracted) position

to ensure that the ram returns freely to its original position

Return tool for repair (see Section 7)

Figure 5

9. REVISION SUMMARY

Latest TE logo and formatting resulting in numbering changes of some paragraphs

Added Warning (paragraph 1)

Moved info on magnetic particle inspection from previous paragraph 5 to new paragraph 6.1.as a

NOTE

Added Section 8 TROUBLESHOOTING and Figure 5

Indice

Altri manuali TE Connectivity Utensili per crimpatura

TE Connectivity

TE Connectivity 2392570-1 Manuale utente

TE Connectivity

TE Connectivity 90260-1 Manuale utente

TE Connectivity

TE Connectivity 528050-3 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 0-1579001-6 Manuale utente

TE Connectivity

TE Connectivity 825508-5 Manuale utente

TE Connectivity

TE Connectivity PDT-48-00 Manuale utente

TE Connectivity

TE Connectivity AMP 3K Guida di riferimento

TE Connectivity

TE Connectivity 2397100-1 Manuale utente

TE Connectivity

TE Connectivity 575937 Manuale utente

TE Connectivity

TE Connectivity TETRA-CRIMP 59824-1 Manuale utente

TE Connectivity

TE Connectivity 69376 Manuale utente

TE Connectivity

TE Connectivity HVA280-2P Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity 2392637-1 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 2-1579016-2 Manuale utente

TE Connectivity

TE Connectivity 2063530-1 Manuale utente

TE Connectivity

TE Connectivity 2063528-1 Manuale utente

TE Connectivity

TE Connectivity 539682-2 Manuale utente

TE Connectivity

TE Connectivity 2386893-1 Manuale utente

TE Connectivity

TE Connectivity 69069 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III 2161732-1 Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

molex

molex 63811-5100 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

molex

molex 63825-3000 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente