TE Connectivity 58425 Series Manuale utente

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1of 4

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111



PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

LOC B

408-9657

75-Ohm Hex Crimp 

Die Assemblies 

58425-[ ] and 58436-[ ] 14 OCT 11 Rev E

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use

and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Figure 1

1. INTRODUCTION

This instruction sheet covers the use and maintenance

of Crimping Dies 58425-[ ] and58436-[ ] (in their

various configurations - denoted by the dash number

following the base part number), used in PRO-

CRIMPER III Hand Tool Frame 354940-1. The dies

crimp 75-Ohm Hex Crimp BNC and TNC plug

connectors onto coaxial cable.

Reasons for reissue of this sheet are provided in

Section 7, REVISION SUMMARY.

NOTE

All dimensions are in millimeters [with inches in

brackets]. Figures and illustrations are for

reference only and are not drawn to scale.



2. DESCRIPTION (Figure 1)

Each die assembly consists of an indenter die and an

anvil die. When closed, the dies form either two or

three crimping chambers (depending on type) which

crimp the center contact and ferrule of the connector

onto the coaxial cable. Each die is held in the tool by a

single screw.

3. DIE INSTALLATION

1. Close the tool handles until the ratchet releases

and then allow them to open fully.

2. See Figure 1 for normal orientation of the dies.

Insert the dies inside the tool jaws and align the

retaining screw holes.

3. Thread the retaining screws into the holes and

carefully close the tool handles. Tighten the screws

with the appropriate hex wrench.

Anvil Die

Stationary Jaw

Hand Tool Frame

354940-1

DieAssemblies58425-[ ]

and 58436-[ ]

Indenter Die Moving Jaw

Insert Center Contact

into Partially Closed

Crimping Dies

Center Contact

Slipped Over

Center Conductor

Ferrule

(Ref)

408-9657

2of 4

Rev E

Figure 2

4. CRIMPING PROCEDURE

4.1. Center Contact

1. Prepare the connector and the cable according to

the instructions packaged with the connector.

2. Slide the center contact onto the center

conductor of the cable; then insert the contact

assembly into the center contact crimp section of

the die. See Figure 2.

NOTE

Make sure that the flange on the end of the center

contact butts against the crimping die. See



Figure 3.

3. Crimp the center contact by holding the cable in

place; then close the tool handles until the ratchet

releases.

4.2. Ferrule

1. Insert the crimped center contact into the

connector body until the cable dielectric butts

against the dielectric inside of the connector body.

The flared braid will then fit around the support

sleeve of the connector body.

2. Slide the ferrule forward over the braid until the

ferrule butts against the shoulder on the connector

body.

3. Place the ferrule on the appropriate anvil of the

die assembly so that the shoulder on the connector

body is butted against the die. See Figure 4.

4. Holding the assembly in place, close the tool

handles until the ratchet releases.

Flange on End of Center

Contact Butts Against Die

Flange on End

of Contact

Crimping Die

Figure 3

CAUTION

Damaged product should not be used. If a

damaged contact or ferrule is evident, it should be

cut from the wire and replaced with a new one. Do

NOT reterminated contact or ferrules.

5. INSPECTION

5.1. Visual Inspection

Inspection of the crimping dies should be made on a

regular basis to ensure that they have not become

worn or damaged. Inspect the crimp sections for

flattened, chipped, worn, or broken areas. If damage

or abnormal wear is evident, the dies must be

replaced. Refer to Section 6, PARTS REPLACEMENT.

Crimping Ferrule

Typical RF

Connector

(Ref)

Shoulder on

Connector Body

Butts Against Die

Ferrule on Anvil

of Crimping Die

Crimping Die

(Ref)

Figure 4

Die 58425-[ ] Die 58436-[ ]

DIE ASSEMBLY

PART NUMBER

CHAMBER CRIMP DIMENSION ±0.10 [.004]

“A" “B” “C” “D”

58425-1 1.07 [.042] (Square) 5.41 [.213] (Hex) 6.48 [.255] (Hex) ---

58425-2 1.07 [.042] (Square) 3.25 [.128] (Hex) 4.52 [.178] (Hex) ---

58425-3 1.07 [.042] (Square) 3.84 [.151] (Hex) 8.23 [.324] (Hex) ---

58436-1 --- 5.41 [.213] (Hex) 6.48 [.255] (Hex) 1.73 [.068] (Hex)

58436-2 --- 2.54 [.100] (Hex) 8.23 [.324] (Hex) 1.73 [.068] (Hex)

58436-3 --- 3.84 [.151] (Hex) 4.52 [.178] (Hex) 1.73 [.068] (Hex)

58436-4 --- 3.73 [.147] (Hex) 4.52 [.178] (Hex) 1.73 [.068] (Hex)

408-9657

3of 4

Rev E

Figure 5

5.2. Measuring Die Opening

The die assembly will perform correctly as long as: 

(1) the product specified is correct for the application,

(2) the specific die assembly is used, (3) the die

assembly has been measured to ensure that the

openings are correct, and (4) the tool has been

adjusted correctly.

Figure 5 provides information on die opening sizes.

5.3. Ratchet Adjustment

The tool frame assembly ratchet mechanism features

an adjustment wheel with eight settings. The

adjustment wheel controls the amount of handle

pressure exerted on the tool jaws and crimping dies

during crimping. If the crimp is not acceptable, adjust

the ratchet as follows:

1. Sufficiently loosen the screw at the ratchet

adjustment wheel so that the wheel can be rotated

above the post that engages the teeth in the wheel.

2. If the crimp is too loose, turn the wheel to a

higher notch (for example, if the wheel is set at

notch no. 5, move the wheel to notch no. 6). If the

crimp is too tight, move the wheel to a lower notch.

3. Tighten the screw at the ratchet adjustment

wheel.

If the crimp cannot be made to conform to the

dimensions provided in the appropriate product

application specification, the tool and/or dies are

defective and must be replaced.

NOTE

Other dies of the PRO-CRIMPER hand tool series

may be used in this tool; however, the ratchet

adjustment wheel may require adjustment to

achieve acceptable crimp height.

6. PARTS REPLACEMENT

Customer-replaceable parts are shown in Figure 1.

Available separately, epair Kit 679221-1 includes a

variety of pins, rings, screws, and springs. If the dies

are damaged or worn excessively, they must be

replaced. Order the repair kit and replaceable parts

through your TE Representative, or call 1-800-526-

5142, or send a facsimile of your purchase order to 1-

717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

7. REVISION SUMMARY

Revisions to this instruction sheet include:

•Changed company name and logo

408-9657

4of 4

Rev E

This Tooling is also Compatible with Die Assemblies 58425-[ ] and 58436-[ ]

PRO-CRIMPER III Hand Tool Frame 354940-1

(Instruction Sheet 408-9930)

SDE-SA Hand Tool 9-1478240-0

(Instruction Sheet 408-8851)

SDE Bench Terminator 1490076-2

(Customer Manual 409-10052)

626 Adapter 679304-1

(Instruction Sheet 408-4070)

Electro-Hydraulic (BT 3500 Battery-Hydraulic)

Hand Tool Kits 2031400-[ ]

(Customer Manual 409-10095)

“C”-Head Assembly 2031450-1

(Instruction Sheet 408-10311)

Closed Head Assembly 2031460-1

(Instruction Sheet 408-10312)

Questo manuale è adatto per i seguenti modelli

Altri manuali TE Connectivity Utensili per crimpatura

TE Connectivity

TE Connectivity 90084 Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 90080-2 Manuale utente

TE Connectivity

TE Connectivity CERTI-CRIMP 90165-1 Manuale utente

TE Connectivity

TE Connectivity 58075-1 Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 4-1579001-2 Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 539 723-2 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 539 748-2 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity 2379381-1 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 5-1579001-2 Manuale utente

TE Connectivity

TE Connectivity 2063574-1 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity AMP 5k/40 CE Manuale utente

TE Connectivity

TE Connectivity MR-1 Manuale utente

TE Connectivity

TE Connectivity PIDG PEEK STRATO-THERM Manuale utente

TE Connectivity

TE Connectivity 90117 Manuale di istruzioni

TE Connectivity

TE Connectivity 91366- 1 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity CERTI-CRIMP II 2381707-1 Manuale utente

TE Connectivity

TE Connectivity 46754-2 Manuale utente

TE Connectivity

TE Connectivity 2393700-1 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

molex

molex 63811-5100 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

molex

molex 63825-3000 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente