TE Connectivity PRO-CRIMPER III Manuale utente

Stationary Jaw Back of Tool

(Wire Side)

Pivot Pin

PRO-CRIMPER III

Hand Crimping Tool

Frame 354940-1 

(408-9930)

Stationary

Handle

Moving Handle

Ratchet

Adjustment Wheel

Moving Jaw

Die Assembly

Front of Tool

(Locator Side)

Locator Assembly

(Supplied with Die Assembly)

TE DIE

ASSEMBLY TE LOCATOR

ASSEMBLY† CONTACT

FAMILY‡ WIRE

SIZE (AWG) INSUL DIA STRIP LENGTH

90871-2 58516-1 .093 Commercial

Pin and Socket 20-18 3.56 [.140] Max 3.96 to 4.72

[.156 to .186]

16-14

† Supplied with die assembly. Also available separately.

‡ Contact the Tooling Assistance Center or Product Information (seebelow) for specific contact part numbers.

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.

1of 6

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111



PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com LOC B

408-9966

PRO-CRIMPER* III Hand

Crimping Tool Assembly 90871-1

with Die Assembly 90871-1 and -2 13 OCT 11 Rev C

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use

and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Figure 1

1. INTRODUCTION

PRO-CRIMPER III Hand Crimping Tool Assembly

90871-1 consists of Die Assembly 90871-2 and PRO-

CRIMPER III Hand Crimping Tool Frame 354940-1.

The die assembly consists of crimping dies and a

locator assembly.

Read these instructions thoroughly before crimping

any contacts.

NOTE

Dimensions on this sheet are in millimeters [with

inchequivalentsprovidedin brackets].Figuresand

illustrations are for identification only and are not

drawn to scale.

Reasons for reissue are provided in Section 11,

REVISION SUMMARY.

2. DESCRIPTION (Figure 1 and Figure 2)

The tool features a tool frame with a stationary jaw

and handle, a moving jaw, a moving handle, and an

adjustable ratchet that ensures full contact crimping.

The tool frame holds a die assembly with two crimping

sections.

The die assembly features a wire anvil, an insulation

anvil, a wire crimper, and an insulation crimper.

Attached to the outside of the frame is a locator

assembly, which contains a locator, a spring retainer,

and a contact support.

Nut

Locator

Chamfer

Insulation

Anvil

Wire

Crimper

Insulation

Crimper

Locator

Assembly Tool Frame

Die Retaining

Pins

Die Retaining

Screw

Die Retaining

Screw

Offset

Wire Anvil

Chamfer

408-9966

2of 6

Rev C

Figure 2

Die retaining pins and die retaining screws are used to

position and secure the dies in the tool frame. A nut is

used on the upper die retaining screw to hold the

locator assembly in place.

3. INSTALLATION AND REMOVAL OF DIE SET AND

LOCATOR ASSEMBLY (Figure 2)

1. Open the tool handles and remove the two die

retaining screws from the tool jaws.

2. Place the wire anvil and insulation anvil so that

their chamfered sides and their marked surfaces

face outward, when mounted in the moving jaw of

the tool frame.

3. Insert the two die retaining pins.

4. Insert the short die retaining screw through the

jaw and through both anvil dies, and tighten the

screw just enough to hold the dies in place. Do not

tighten the screw completely at this time.

5. Place the wire crimper and insulation crimper so

that their chamfered sides and their marked

surfaces face outward, when mounted in the

stationary jaw of the tool frame.

6. Insert the two die retaining pins.

7. Insert the long die retaining screw through the

jaw and through both crimper dies, and tighten the

screw just enough to hold the dies in place. Do not

tighten the screw completely at this time.

8. Carefully close the tool handles, making sure that

the anvils and crimpers align properly. Continue

closing the tool handles until the ratchet in the tool

frame has engaged sufficiently to hold the anvils

and crimpers in place, then tighten both die

retaining screws.

9. Place the locator assembly over the end of the

long screw, and position the locator assembly

against the side of the tool jaw.

10. Place the nut onto the end of the long screw and

tighten the nut enough to hold the locator assembly

in place, while still allowing the locator to slide up

and down.

11. To disassemble, close the tool handles until the

ratchet releases, remove the nut, the locator

assembly, the two die retaining screws, and the four

die retaining pins, and slide the anvils and crimpers

out of the tool jaws.

4. CONTACT SUPPORT ADJUSTMENT (Figure 3)

NOTE

The contact support is preset priorto shipment, but

minor adjustment may be necessary.



1. Make a sample crimp and determine if the

contact is straight, bending upward, or bending

downward.

2. If adjustment is required, loosen the screw that

holds the contact support onto the locator assembly.

NOTE

408-9966

3of 6

Rev C

The ratchet has detents that create audible clicks

as the tool handles are closed.

3. Place a contact with wire into the proper nest and

close the tool handles until the ratchet reaches the

sixt# click, or until the contact support touches the

contact.

4. Slightly loosen the nutthat holds the locator

assembly onto the tool frame.

5. Move the contact support as required to eliminate

the bending of the contact.

6. Tighten the nut and close the handles until the

ratchet releases.

7. Remove and inspect the contact.

8. Make another sample crimp. If the contact is

straight, tighten the contact support screw. If the

contact is still being bent during crimping, repeat the

adjustment procedure.

5. CRIMPING PROCEDURE

NOTE

This tool is provided with a crimp adjustment

feature. Initially, the crimp height should be verified

as specified in Figure 4. Refer to Section 6, Crimp

Height Inspection, and Section 7, RATCHET

Adjustment, to verify crimp height before using the

tool to crimp desired contacts and wire sizes.

Refer to the table in Figure 1 and select wire of the

specified size and insulation diameter. Strip the wire to

the length indicated in Figure 1, taking care not to nick

or cut wire strands. Select an applicable contact and

identify the appropriate crimp section according to the

wire size markings on the tool. Refer to Figure 3 and

proceed as follows:

1. Hold the tool so that the back (wire side) is facing

you. Squeeze tool handles together and allow them

to open fully.

2. Holding the contact by the mating end, insert the

contact - insulation barrel first - through the front of

the tool and into the appropriate crimp section.

3. Position the contact so that the mating end of the

contact is on the locator side of the tool, and so that

the open "U" of the wire and insulation barrels face

the top of the tool. Place the contact up into the nest

so that the movable locator drops into the slot in the

contact. Refer to Figure 3. Butt the front end of the

wire barrel against the movable locator.

CAUTION

Make sure that both sides of the insulation barrel

are started evenly into the crimping section. Do not

attempt to crimp an improperly positioned contact.

Contact

Support

Adjustment

ScrewforContact

Support

Locator

Back of Tool

(Wire Side)

Wire

Contact

(Typ)

Locator

in Wire

Stop Slot

Strip

Length

Wire

Inserted

to Stop

Figure 3

408-9966

4of 6

Rev C

4. Hold the contact in position and squeeze the tool

handles together until ratchet engages sufficiently to

hold the contact in position. Do NOT deform

insulation barrel or wire barrel.

5. Insert stripped wire into contact insulation and

wire barrels until it is butted against the wire stop, as

shown in Figure 3.

6. Holding the wire in place, squeeze tool handles

together until ratchet releases. Allow tool handles to

open and remove crimped contact.

NOTE

Thecrimpedcontactmaystickinthecrimpingarea,

but the contact can be easily removed by pushing

downward on the top of the locator (see Figure 3).

7. Check the contact's crimp height as described in

Section 6, Crimp Height Inspection. If necessary,

adjust the crimp height as described in Section 7,

RATCHET ADJUSTMENT.

6. CRIMP HEIGHT INSPECTION

Crimp height inspection is performed through the use

of a micrometer with a modified anvil, commonly

referred to as a crimp-height comparator. TE does not

manufacture or market crimp-height comparators.

Detailed information on obtaining and using crimp-

height comparators can be found in instruction sheet

408-7424.

Proceed as follows:

1. Refer to Figure 4 and select a wire (maximum

size) for each crimp section listed.

2. Refer to Section 5, CRIMPING PROCEDURE,

and crimp the contact(s) accordingly.

PositionPoint

on Center of

Wire Barrel

Opposite

Seam

Modified Anvil

WIRE SIZE

AWG (Max) CRIMP SECTION

(Wire Size Marking) CRIMP HEIGHT

DIMENSION “A”

18 20-18 1.07 [.042]

14 16-14 1.45 [.057]

Figure 4

3. Using a crimp height comparator, measure the

wire barrel crimp height as shown in Figure 4. If the

crimp height conforms to that shown in the table,

the tool is considered dimensionally correct. If not,

the tool must be adjusted. Refer to Section 7,

RATCHET (Crimp Height) ADJUSTMENT.

7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)

1. Remove the lockscrew from the ratchet

adjustment wheel.

2. With a screwdriver, adjust the ratchet wheel from

the locator side of the tool.

Screwdriver

Ratchet

Adjustment

Wheel

Lockscrew

(Typ)

Figure 5

3. Observe the ratchet adjustment wheel. If a tighter

crimp is required, rotate the adjustment wheel

COUNTERCLOCKWISE to a higher-numbered

setting. If a looser crimp is required, rotate the

adjustment wheel CLOCKWISE to a lower-

numbered setting.

4. Replace the lockscrew.

5. Make a sample crimp and measure the crimp

height. If the dimension is acceptable, replace and

secure the lockscrew. If the dimension is

unacceptable, continue to adjust the ratchet, and

again measure a sample crimp.

408-9966

5of 6

Rev C

8. MAINTENANCE

Ensure that the tool and dies are clean by wiping them

with a clean, soft cloth. Remove any debris with a

clean, soft brush. Do not use objects that could

damage the tool. When not in use, keep handles

closed to prevent objects from becoming lodged in the

crimping dies, and store in a clean, dry area.

9. VISUAL INSPECTION

The crimping dies should be inspected on a regular

basis to ensure that they have not become worn or

damaged. Inspect the crimp sections for flattened,

chipped, worn, or broken areas. If damage or

abnormal wear is evident, the tool must be replaced.

See Section 10, REPLACEMENT.

10. REPLACEMENT

Customer-replaceable parts are shown in Figure 1.

Available separately, PRO-CRIMPER III Hand

Crimping Tool Repair Kit 679221-1 includes a

replacement nut and a variety of pins, rings, screws,

and springs.

If the dies are damaged or worn excessively, they

must be replaced.

Order the repair kit and replaceable parts through your

TE representative, or call 1-800-526-5142, or send a

facsimile of your purchase order to 1-717-986-7605, or

write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

11. REVISION SUMMARY

Revisions to this instruction sheet include:

•Changed company name and logo

Tooling Used With 90871-2

408-9966

6of 6

Rev C

Altri manuali per PRO-CRIMPER III

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali TE Connectivity Utensili per crimpatura

TE Connectivity

TE Connectivity MQS 3-1579014-9 Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 5-1579001-3 Manuale utente

TE Connectivity

TE Connectivity SDE-SA 2389861-1 Manuale utente

TE Connectivity

TE Connectivity 2380840-1 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity TERMI-FOIL 68026 Manuale utente

TE Connectivity

TE Connectivity AMPOWER 68361-1 Manuale utente

TE Connectivity

TE Connectivity 825508-5 Manuale utente

TE Connectivity

TE Connectivity SDE-SA PN 2063626-1 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity 90080-2 Manuale utente

TE Connectivity

TE Connectivity 2063409-1 Manuale utente

TE Connectivity

TE Connectivity 90260-1 Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 2379381-1 Manuale utente

TE Connectivity

TE Connectivity 2390075-1 Manuale utente

TE Connectivity

TE Connectivity 2844594-1 Manuale utente

TE Connectivity

TE Connectivity 2844461-2 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity 2362810-1 Manuale utente

TE Connectivity

TE Connectivity 46447 Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III 58521-1 Manuale utente

TE Connectivity

TE Connectivity AT-SC Manuale utente

TE Connectivity

TE Connectivity 539 726-2 Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

Panduit

Panduit CT-1000 Guida per l'amministratore

JST

JST CS 10 Manuale utente

molex

molex 63811-5100 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

molex

molex 63825-3000 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

Tyco Electronics

Tyco Electronics CERTI-CRIMP 90418-1 Manuale utente