TE Connectivity T2212 Manuale utente
Operator's Manual
T2212 PRINTER CUTTER
2 2
Operator's Manual
Doc. # 412-121038 revision 1
Copyright
This documentation as well as translation hereof are property of TE Connectivity (TE).
The replication, conversion, duplication or divulgement of the whole manual or parts
of it for other intentions than its original intended purpose demands the previous
written authorization by TE Connectivity.
Trademark
Windows is a registered trademark of the Microsoft Corporation.
Editor
Regarding questions or comments please contact TE Connectivity.
Topicality
Due to the constant further development of our products discrepancies between
documentation and products can occur.
Please check with your local TE Connectivity Representative for the latest update.
For technical support please use Technical Support link below, for regional contact
details:
Technical Support
3
1 Introduction....................................................................................4
1.1 Instructions ......................................................................................4
1.2 Intended Use ...................................................................................5
1.3 Safety Instructions ...........................................................................6
1.4 Environment.....................................................................................6
1.5 Technical Data .................................................................................6
2 Mounting.........................................................................................7
2.1 Removing the Tear-off Plate ............................................................7
2.2 Mounting the Cutter .........................................................................8
3 Operation........................................................................................9
3.1 Loading Material ..............................................................................9
3.2 Standard Operation .......................................................................10
3.3 Cutting on Demand........................................................................10
4 PrinterConguration................................................................... 11
5 Cleaning and Replacing the Blades........................................... 13
6 Licenses .......................................................................................15
6.1 Reference to the EU Declaration of Conformity.............................15
6.2 FCC ...............................................................................................15
Table of Contents
4 41 Introduction
1.1 Instructions
Important information and instructions in this documentation are designated
as follows:
Danger!
Draws your attention to an exceptionally grave, impending danger
to your health or life.
!
Warning!
Indicates a hazardous situation that could lead to injuries or
material damage.
!
Attention!
Draws attention to possible dangers, material damage or loss of
quality.
i
Note!
Gives you tips. They make a working sequence easier or draw
attention to important working processes.
Environment!
Gives you tips on protecting the environment.
Handling instruction
Reference to section, position, illustration number or document.
Option (accessories, peripheral equipment, special ttings).
Time Information in the display.
51 Introduction
1.2 Intended Use
• The cutter unit is intended exclusively as an option for the T2212 Printer,
for cutting material approved by TE Connectivity. Details of approved
materials are found in TE document 411-121005 (Identication Printer
Product Ribbon Matrix). TE Connectivity shall not be liable for damage
resulting from unauthorized use; the user shall bear the risk alone.
• Usage for the intended purpose also includes complying with the operating
manual, including the manufacturer‘s maintenance recommendations and
specications.
• The device is manufactured in accordance with the current technological
status and the recognized safety rules. However, danger to the life and
limb of the user or third parties and/or damage to the device and other
tangible assets can arise during use.
• The device may only be used for its intended purpose and if it is in perfect
working order, and it must be used with regard to safety and dangers as
stated in the operating manual.
i
Note!
This, and further TE documents can be downloaded from TE.COM at
the following link.
http://www.te.com/commerce/DocumentDelivery/DDEController
!
Warning!
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
6 61 Introduction
1.3 Safety Instructions
• Disconnect the printer from the electrical outlet before mounting or
removing the cutter.
• The cutter may only be operated when it is mounted on the printer.
• Risk of injury, particularly during maintenance, the cutter blades are sharp.
• Work going beyond this may only be performed by trained personnel or
service technicians.
• Unauthorized interference with electronic modules or their software can
cause malfunctions. Other unauthorized work on or modications to the
device can also endanger operational safety.
• Always have service work done in a qualied workshop, where the
personnel have the technical knowledge and tools required to do the
necessary work. Technical Support
• Warning stickers must not be removed, as then you and other people
cannot be aware of dangers and may be injured.
1.4 Environment
Obsolete devices contain valuable recyclable materials that should be sent
for recycling.
Send to suitable collection points, separately from residual waste.
The modular construction of the printer enables it to be easily disas-
sembled into its component parts.
Send the parts for recycling.
Take the electronic circuit boards to public waste disposal centers or to
the distributor.
1.5 Technical Data
Cutter
for printer type
T2212
Cutting length mm ≥ 10
Cut frequency 1/min ≤ 200
Power Supply Cutter connector of the printer
!
Attention!
The minimum cut length is depending on the media, in particular its
adhesive characteristics.
Perform preliminary tests. Test the media too, if the media is
veryhard,veryexibleorverythin.
72 Mounting
2.1 Removing the Tear-off Plate
Before mounting the cutter the tear-off plate mounted on the printer must be
removed.
2
1
3
2
3
Figure 1 Removing the tear-off plate
Gently pull the tear off plate forward (1), pull the axles (2) of the tear-off
plate out of the holders (3) and remove the tear-off plate.
93 Operation
3.1 Loading Material
Gently pull the cutter unit forward as shown in Figure 3,
Insert labels or continuous tube between the Printhead and drive roller, so
that the front edge reaches through the cutter unit.
21
Figure 3 Guiding labels and tube into the cutter unit
Guide labels or tube (2) into slot (1), then engage the cutter unit by gently
pushing the cutter unit back on the printer.
Insert ribbon.
Operator's manual of the printer (TE Document 412-121037).
10 103 Operation
3.2 Standard Operation
Switch on the printer.
The cutter performs a synchronization action.
i
Note!
To operate the cutter with continuous material in the printer menu
Setup ->Labels ->Label sensor the setting Continuous media has to be
selected. Otherwise no synchronization cut is carried out.
Press . For synchronization the media will be moved forward and
cut off.
That synchronization is not necessary when the printhead was not opened
between print jobs, even if the printer was powered off between print jobs.
Send a print job.
All labels in the job will be printed without stopping and be cut as chosen in
the software : after each label, after a specic quantity of labels, or at the
end of a print job.
i
Note!
Between the print jobs a direct cut can be released by pressing
on the control panel.
3.3 Cutting on Demand
In the "Cut on Demand" mode the print job will be split into steps, which can
be released separately.
Choose Printing > Print on demand = On.
4. Printer Conguration.
Send a print job.
Press .
The rst label will be printed and cut.
Press again to print and cut the next label.
Altri manuali per T2212
3
Indice
