TE Connectivity 58536-1 Manuale utente

1 of 4

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners.

TOOLING ASSISTANCE CENTER

1-800-722-1111

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com.

Instruction Sheet

408-4028

06 JUN 14 Rev B

Figure 1

1. INTRODUCTION

Crimping Die Assembly 58536-1 is designed to crimp 75-Ohm RF Series BNC Dual-Crimp Connectors when

used in PRO-CRIMPER III Frame Assembly 354940-1.

Catalog 82074 provides a guide for cable-to-connector selection. For connectors not referenced in the catalog,

contact TE Product Engineering for recommendations.

Reasons for reissue are provided in Section 8, REVISION SUMMARY.

NOTE

Dimensions in this instruction sheet are in millimeters [with inches in brackets]. Figures and illustrations are for reference only

and are not drawn to scale.

2. DESCRIPTION

The die assembly consists of an indenter die and an anvil die, which when closed form three crimping

chambers. The two larger crimping chambers crimp the ferrule of the connector onto the coaxial cable, and the

smaller crimping chamber crimps the center contact onto the center conductor of the coaxial cable. Each die is

held in the tool jaws by a single screw. See Figure 1.

3. DIE INSTALLATION (Figure 1)

1. Close the tool handles until the ratchet releases, then allow the tool handles to open fully.

2. Install anvil die in the movable jaw of the tool frame. Align the die with the retaining screw hole, then

secure die with the die-retaining screw. Do NOT fully tighten.

3. Install indenter die in the stationary jaw of the tool frame. Slowly close the tool handles, allowing the

dies to align themselves.

PROPER USE GUIDELINES

Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low

volume applications. A wide selection of powered application equipment for extended-use, production operations is available.

Crimping Die

Assembly 58536-1

The PRO-CRIMPER III Hand Tool is a “Commercial” grade tool and

is designed primarily for field installation, repair, maintenance work,

or prototyping in industrial, commercial, or institutional applications.

Product crimped with this tool will meet the crimp height requirement

for hand tools in the appropriate 114 application specification, but

may not comply with other feature parameters of the specification.

TE Connectivity offers a variety of tools to satisfy your performance

requirements. For additional information, contact the Technical

Assistance Center at 1-800-722-1111.

Indenter Die

Crimping Die

Assembly

58536-1

Anvil Die

Center Contact

Crimping Chamber

Ferrule

Crimping

Chambers

PRO-CRIMPER* III

Frame Assembly

354940-1 (Ref)

408-4028

Rev B

2 of 4

NOTE

Once the anvil has entered the indenter, place a copper bus bar (1.5 ±0.05 [.062 ±.002] diameter) into the center contact

crimping chamber of the die assembly.

4. Close the tool handles completely.

5. Securely tighten both screws with the appropriate screwdriver.

4. CRIMPING PROCEDURE

Select the appropriate cable size and connector. The wire size and insulation diameter must be within the

specified range for the connector.

NOTE

This tool is provided with a crimp height adjustment feature. Initially, the crimp height should be verified. Refer to Section 5,

Crimp height Adjustment, to verify crimp height before using the tool.

For detailed information on cable strip lengths and proper assembly of the connector, refer to the instructions

packaged with the connector. Make sure that the connector's ferrule has been placed onto the cable, and that

the cable's braided shield is flared away from the cable. Then proceed as follows:

4.1. Crimping the Center Contact (Figure 2)

1. Close the tool handles until the dies are partially closed.

2. Assemble the center contact onto the cable center conductor and place the center contact in the

smallest crimping chamber of the anvil die. Make sure the flange on the end of the center contact

butts against the die.

3. Holding the cable in place, close the tool handles until the ratchet releases.

4. Allow the tool handles to open fully and remove the crimped center contact from the dies.

Figure 2

4.2. Crimping the Ferrule (Figure 3)

1. Insert the crimped center contact into the connector body until the cable dielectric butts against the

dielectric inside the connector body or until the center contact is securely positioned within the

connector. Make sure that the braided shield is over the support sleeve of the connector body and that

no strands from the shield enter the connector body.

Crimping the

Center Contact

Flange on End of

Center Contact

Butts Against Die

Anvil Die

Stripped

Cable

Cross-Sectional View

Plug Contact

Jack Contact

Flange on

End of

Contact

Flange on

End of

Contact

Crimping Die

408-4028

Rev B

3 of 4

Figure 3

2. Slide the ferrule up over the braided shield and onto the connector until the ferrule butts against the

shoulder on the connector body.

3. Place the ferrule in the appropriate crimping chamber of the anvil die so that the shoulder on the

connector body butts against the edge of the die.

NOTE

Refer to the instruction sheet packaged with the connector to determine the appropriate crimping chamber for the ferrule.

4. While holding the assembly together, begin to close the tool handles. Keep holding the assembly until

the dies have closed enough to clamp the assembly in place.

CAUTION

Make sure that both sides of the ferrule are started evenly into the crimping chamber. Do not attempt to crimp an improperly

positioned ferrule.

5. Carefully close the tool handles until the ratchet releases.

6. Allow the tool handles to open fully and remove the crimped connector from the dies.

5. CRIMP HEIGHT ADJUSTMENT (Figure 4)

The tool frame assembly ratchet mechanism features an adjustment wheel with numbered settings. If the crimp

height is not acceptable, adjust the ratchet as follows:

1. Remove the lockscrew from the ratchet adjustment wheel.

2. With a screwdriver, adjust the ratchet wheel from the opposite side of the tool.

Figure 4

3. Observe the ratchet adjustment wheel. If a tighter crimp is required, rotate the adjustment wheel

COUNTERCLOCKWISE to a higher- numbered setting. If a looser crimp is required, rotate the

adjustment wheel CLOCKWISE to a lower-numbered setting.

Crimping the

Ferrule

Shoulder on

Connector

Body Butts

Against Edge

of Die

Ferrule in

Crimping

Chamber on

Anvil Die

Screwdriver

Ratchet

Adjustment

Wheel

Lockscrew

(Typ)

408-4028

Rev B

4 of 4

4. Replace the lockscrew.

5. Make a sample crimp and measure the crimp height. If the crimp height is acceptable, secure the

lockscrew. If the dimension is unacceptable, remove lockscrew and continue to adjust the ratchet, and

again measure a sample crimp.

6. MAINTENANCE AND INSPECTION

6.1. Maintenance

1. Remove dust, moisture, and other contaminants with a clean, soft brush, or a clean, soft, lint-free

cloth. Do NOT use any objects that could damage the dies or tool.

2. Make sure that the proper die-retaining screws are properly secured.

3. When the dies are not in use, store them in a clean, dry area.

4. Store the tool with the tool handles closed to prevent objects from becoming lodged within the jaws.

6.2. Inspection

1. Remove all lubrication and accumulated film from the dies by immersing the dies in a suitable

commercial degreaser.

2. Make certain that all die-retaining screws and die components are properly secured.

3. Inspect the crimping surfaces for flattened, chipped, worn, or cracked areas. If damage is evident, the

dies must be replaced. Refer to Section 7, REPLACEMENT.

6.3. Measuring Die Opening

The die assembly will perform correctly as long as: (1) the product specified is correct for the application, (2)

the specific die assembly is used, (3) the die assembly has been measured to ensure that the openings are

correct, and (4) the tool has been adjusted correctly. Figure 5 provides information on die opening sizes.

7. REPLACEMENT

Crimping Die Assembly 58536-1 is inspected before shipment. TE recommends that the dies be inspected

immediately upon arrival at your facility to ensure that the dies have not been damaged during shipment.

Order replacements through your local TE Representative, or call 1-800-526-5142, or send a facsimile of your

purchase order to 1-717-986-7605, or write to:

CUSTOMER SERVICE (038-035)

TYCO ELECTRONICS CORPORATION

PO BOX 3608

HARRISBURG PA 17105-3608

8. REVISION SUMMARY

Updated company logo

Figure 5

B (Ref)

DIE CLOSURE DIMENSIONS (mm [in.])

1.12 ±0.05

[.044 ±.002]

6.10 ±0.10

[.240 ±.004]

6.73 ±0.10

[.265 ±.004]

A (Ref)

C (Ref)

NOTE: Not to Scale

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

TE Connectivity:

58536-1

Indice

Altri manuali TE Connectivity Utensili elettrici

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity OCEAN 2.0 Manuale utente

TE Connectivity

TE Connectivity 46447 Manuale utente

TE Connectivity

TE Connectivity 408-160034 Manuale utente

TE Connectivity

TE Connectivity 2377026-1 Manuale utente

TE Connectivity

TE Connectivity 2405856-1 Manuale utente

TE Connectivity

TE Connectivity 2031676-1 Manuale utente

TE Connectivity

TE Connectivity 2031991-1 Manuale utente

TE Connectivity

TE Connectivity SDE-SA Manuale utente

TE Connectivity

TE Connectivity HPi 10 TE Manuale di istruzioni

TE Connectivity

TE Connectivity HT40 Manuale utente

TE Connectivity

TE Connectivity 59981-1 Manuale utente

TE Connectivity

TE Connectivity 2389783-1 Manuale utente

TE Connectivity

TE Connectivity 2381114-1 Manuale utente

TE Connectivity

TE Connectivity SOLARLOK PN 1-1579004-1 Manuale utente

TE Connectivity

TE Connectivity 2390408-1 Manuale utente

TE Connectivity

TE Connectivity 2389862-1 Manuale utente

TE Connectivity

TE Connectivity 1055258-1 Manuale utente

TE Connectivity

TE Connectivity CAPI-6T Manuale utente

TE Connectivity

TE Connectivity PRO- CRIMPER III Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 7-1579004-1 Manuale utente

TE Connectivity

TE Connectivity NanoMQS 2280687-1 Manuale utente

TE Connectivity

TE Connectivity Micro-MaTch 528405-9 Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale