Teac CTM6828S Manuale utente
SERVICE MANUAL
Version 2-68 cm CTV
Effective: MAY 2000 CTM6828V2SERV
TECHNICAL BULLETIN 26-Jun-00
Page 1of 1
MODEL: CT-M5930S, CT-M6828S, CT-F683
PROBLEM:
RF Interference
File: CTM5830 6828 683 rf interf tb.doc
Some units of the first production lot for the models of reference have been supplied with a low quality RF lead
from the RF connector in the back panel to the tuner input. Those units may display diagonal interference lines
on the picture mainly in VHF bands.
Note that the braid of the good quality cable is very tight and totally covers the internal wire.
Instructions
Replaced the faulty RF cable assembly using the part number 40252200111.
Regards,
Alcides Berta
TEAC Australia Pty Ltd.
TECHNICAL BULLETIN 12-July-2000
Page 1of 1
MODEL: CT-F683, CT-M6828S, CT-M5930
PROBLEM:
I2C Mitsubishi chassis. Service Mode adjustments
File: CT-F683 CT-M6828 5930 RC tb.doc
The following information applies to all Great Wall models using I2C Mitsubishi technology. A
special type of remote control is necessary to access Service Mode adjustments, please refer to
the figure.
Accessing Service Mode
1-Press first button on the left of the FACTORY ON row (Button 1). The
word Key is visible on the screen.
2-Press FACTORY button (Button 2). The first page of factory
adjustments will be displayed.
3-Navigate between parameters and different pages using UP and DOWN
buttons. Direct access to frequently used parameters is available from
dedicated buttons, for example EW WIDTH, V AMPL, etc.
4-Adjust parameter values using VALUE+ and VALUE -.
Leaving Service Mode
1-Press first button on the left of the FACTORY ON row (Button 1). The
work Key is visible on the screen.
2-Press STANDBY button.
3-Turn POWER off from the front panel switch for at least 15 seconds.
Note:
The final version of remote control may be slightly different from the one used
to prepare this bulletin.
Regards,
Alcides Berta
TEAC Australia Pty Ltd.
TECHNICAL BULLETIN 21-Jul-2000
Page 1of 1
MODEL: CT-M6828S CT-F683 CT-M5930S
PROBLEM:
Audio noise
File: CT M6828S M5930S F683 noise tb.doc
A humming noise is audible at low volume from the speakers and particularly from the headphone
output (when available). The source of this noise is the vertical deflection circuit.
Instructions
1-Delete the jumper W286 on the main PCB next to CN111 in the fly-back transformer area.
2-Add a cable between the IF shielding can and the heat sink for the audio output IC.
Regards,
Alcides Berta
TEAC Australia Pty Ltd.
TECHNICAL BULLETIN 11-August-2000
Page 1of 1
MODEL: CT-M6828S, CT-M5930 and CT-F683
PROBLEM: Incorrect resistor type
File: CT-M6828S m oxide.doc
An incorrect resistor type has been fitted in position R504 of the neck board in some units. A
carbon film resistor having a light brown color body and mounted on the surface of the PCB can
eventually ignite and burn the board.
Instructions
Replace the carbon film resistor in location R504 with a metal oxide type. Separate the new
resistor from the surface of the PCB by approximately 10 mm.
Alcides Berta
TEAC Australia Pty Ltd.
Wrong type
Carbon film resistor
PN: 11347020512
47 Ohm, ½ W
Correct type
Metal oxide resistor
PN: 11347020575
47 Ohm, ½ W
Indice
Altri manuali Teac TV
Teac
Teac EU-68 Manuale utente
Teac
Teac DV-TV5100 Manuale utente
Teac
Teac LE32G6FHD Manuale utente
Teac
Teac CT-M3442H Manuale utente
Teac
Teac 3290I Manuale utente
Teac
Teac LEV2292FHD Manuale utente
Teac
Teac EU-34HT Manuale utente
Teac
Teac CT-M3497 Manuale utente
Teac
Teac LE40A4E1FHD Manuale utente
Teac
Teac EU3242ST Manuale utente
Teac
Teac EU-51 Manuale utente
Teac
Teac CT-F5151 Manuale utente
Teac
Teac EU2845ST Manuale utente
Teac
Teac CT-F803 Manuale utente
Teac
Teac CT-M519 Manuale utente
Teac
Teac CT-F687 Manuale utente
Teac
Teac LEV24GD3FHD Manuale utente
Teac
Teac 3290 Manuale utente
Teac
Teac EU 3216STF Manuale utente
Teac
Teac CT-M808SV Manuale utente
