Tech Controllers EU-283c WiFi Manuale utente

EU- 283c WiFi

TABLE OF CONTENTS

I. Safety ......................................................................................................................................................................... 3

II. Device description ..................................................................................................................................................... 4

III. Installation................................................................................................................................................................. 4

IV. Main screen description............................................................................................................................................5

V. Schedule ...................................................................................................................................................................... 5

1. Schedule ................................................................................................................................................................... 5

2. Schedule settings......................................................................................................................................................5

3. Additional contacts................................................................................................................................................... 6

a) Pairing....................................................................................................................................................................... 6

b) Contact removal ....................................................................................................................................................... 6

4. Window sensors ....................................................................................................................................................... 6

a) ON.............................................................................................................................................................................6

b) Delay time................................................................................................................................................................. 7

c) Information ............................................................................................................................................................... 7

d) Pairing....................................................................................................................................................................... 7

e) Sensor removal......................................................................................................................................................... 7

5. Calibration ................................................................................................................................................................ 7

6. Hysteresis ................................................................................................................................................................. 7

7. ON............................................................................................................................................................................. 7

VI. Controller menu......................................................................................................................................................... 8

1. Block diagram of main menu.................................................................................................................................... 8

2. WiFi module .............................................................................................................................................................9

3. Time settings ............................................................................................................................................................ 9

4. Screen settings ......................................................................................................................................................... 9

5. Prenatal lock........................................................................................................................................................... 10

6. Software version .................................................................................................................................................... 10

7. Service menu.......................................................................................................................................................... 10

8. Factory settings ......................................................................................................................................................10

9. Manual mode ......................................................................................................................................................... 10

10. Language selection............................................................................................................................................. 10

VII. How to control the heating system via www.emodul.eu ......................................................................................11

1. Home tab................................................................................................................................................................ 12

2. Zones tab................................................................................................................................................................ 16

3. Statistics ................................................................................................................................................................. 16

4. Settings tab.............................................................................................................................................................17

VIII. Protections and alarms............................................................................................................................................ 18

IX. Software update......................................................................................................................................................18

X. Technical data..........................................................................................................................................................18

KN.2020.05.11

I. SAFETY

Before using the device for the first time the user should read the following regulations carefully. Not obeying the rules

included in this manual may lead to personal injuries or controller damage. The user’s manual should be stored in a safe

place for further reference. In order to avoid accidents and errors it should be ensured that every person using the device

has familiarized themselves with the principle of operation as well as security functions of the controller. If the device is

to be sold or put in a different place, make sure that the user’s manual is there with the device so that any potential user

has access to essential information about the device.

The manufacturer does not accept responsibility for any injuries or damage resulting from negligence; therefore, users

are obliged to take the necessary safety measures listed in this manual to protect their lives and property.

WARNING

High voltage! Make sure the regulator is disconnected from the mains before performing any activities involving

the power supply (plugging cables, installing the device etc.).

The device should be installed by a qualified electrician.

The regulator should not be operated by children.

NOTE

The device may be damaged if struck by a lightning. Make sure the plug is disconnected from the power supply

during storm.

Any use other than specified by the manufacturer is forbidden.

Before and during the heating season, the controller should be checked for condition of its cables. The user

should also check if the controller is properly mounted and clean it if dusty or dirty.

Changes in the merchandise described in the manual may have been introduced subsequent to its completion on May

11th 2020. The manufacturer retains the right to introduce changes to the structure. The illustrations may include

additional equipment. Print technology may result in differences in colours shown.

Care for the natural environment is our priority. Being aware of the fact that we manufacture

electronic devices obligates us to dispose of used elements and electronic equipment in a

manner which is safe for nature. As a result, the company has received a registry number

assigned by the Main Inspector of Environmental Protection. The symbol of a crossed out

rubbish bin on a product means that the product must not be thrown out to ordinary waste

bins. By segregating waste intended for recycling, we help protect the natural environment.

It is the user's responsibility to transfer waste electrical and electronic equipment to the

selected collection point for recycling of waste generated from electronic and electrical

equipment.

II. DEVICE DESCRIPTION

Controller features:

Front panel made of 2 mm glass

Large colour touch screen

Built-in temperature sensor

Built-in WiFi module

Flush-mountable

III. INSTALLATION

Controller should be installed by a qualified person.

WARNING

Risk of fatal electric shock from touching live connections. Before working on the controller switch off the power

supply and prevent it from being switched on again.

NOTE

Incorrect connection of the wires may damage the regulator!

IV. MAIN SCREEN DESCRIPTION

The regulator is controlled using touch screen.

1. Enter the controller menu

2. Regulator operation mode - the pre-set temperature is selected according to the schedule or manual settings (manual

mode). Touch the screen here to open up a schedule selection panel

3. Current time and date

4. Time left before the next change of the pre-set temperature in current operation mode

5. Pre-set zone temperature - tap on the screen here to edit this value. Once the temperature has been changed manually,

manual mode is activated in the zone

6. Current zone temperature

7. Icon informing about window opening or closing

V. SCHEDULE

1. SCHEDULE

Pressing this icon activates / deactivates the controller's operating mode according to a set schedule.

2. SCHEDULE SETTINGS

After entering the schedule editing screen, the schedule may be adjusted to the user’s needs. The settings may be

configured for two separate groups of days –the first group in blue, the second one in grey. It is possible to assign up to

3 time periods with separate temperature values to each group. Outside these periods, a general pre-set temperature

will apply (its value may also be edited by the user).

1. General pre-set temperature for the first group of days (blue colour –in the example above the colour is used to mark

working days Monday-Friday). The temperature applies outside the time periods defined by the user.

2. Time periods for the first group of days –the pre-set temperature and the time limits. Tapping on a given period opens

up an editing screen.

3. General pre-set temperature for the second group of days (grey colour –in the example above the colour is used to

mark Saturday and Sunday).

4. Time periods for the second group of days.

5. Days of the week –blue days are assigned to the first group whereas grey days are assigned to the second one. In order

to change the group, tap on a selected day.

If the time periods overlap, they are marked with red colour. Such settings cannot be confirmed.

3. ADDITIONAL CONTACTS

A) PAIRING

In order to register the actuator, select ‘Pairing’ in Additional contacts submenu and press quickly the communication

button (found under the actuator cover). Release the button and watch the control light:

- control light flashes twice - proper communication established

- control light lights up continuously - no communication with the main controller

B) CONTACT REMOVAL

This option enables the user to remove the actuators in a given zone.

4. WINDOW SENSORS

A) ON

This option is used to activate registered sensors.

B) DELAY TIME

When the pre-set delay time is over, the main controller sends the

information to the actuators forcing them to close. Time setting

range is 00:00 –00:30 minutes.

Example:

Delay time is set at 10 minutes.

When the window is opened, the sensor sends the information to

the main controller. If the sensor sends another information that the

window is open after 10 minutes, the main controller will force the

actuators to close.

NOTE

If the delay time is set at 0 minutes, the message forcing the

actuators to close will be sent immediately.

C) INFORMATION

Select this option to view all sensors.

D) PAIRING

In order to register the sensor, select ‘Pairing’ in Additional contacts submenu and press quickly the communication

button. Release the button and watch the control light:

- control light flashes twice - proper communication established

- control light lights up continuously - no communication with the main controller

E) SENSOR REMOVAL

This option is used to remove the sensors in a given zone.

5. CALIBRATION

Calibration of the room sensor should be performed while mounting or after the regulator has been used for a long time,

if the room temperature measured by the sensor differs from the actual temperature. Calibration setting range is from -

10 to +10⁰C with the accuracy of 0,1⁰C.

6. HYSTERESIS

This function is used to define tolerance of the pre-set temperature in order to prevent undesired oscillation in case of

small temperature fluctuation (within the range 0,1 ÷ 2,5⁰C) with the accuracy of 0,1°C.

Example: if the pre-set temperature is 23⁰C and the hysteresis is 0,5⁰C, the room temperature is considered too low when

it drops to 22,5⁰C.

7. ON

This function enables the user to activate the devices assigned to a given zone.

VI. CONTROLLER MENU

1. BLOCK DIAGRAM OF MAIN MENU

WiFi module

WiFi network selection

Registration

DHCP

IP address

Gate address

DNS address

MAC address

Subnet mask

Module version

Time settings

Clock settings

Date settings

Screen settings

Screensaver

Screen brightness

Screen blanking

Screen blanking time

Prenetal lock

Auto-lock ON

Auto-lock OFF

Auto-lock PIN codeSoftware version

Service menu

Factory settings

Manual mode

OFF

Language

2. WIFI MODULE

The controller features a built-in Internet module enabling the user to monitor the status of all system devices on a

computer screen, a tablet or a mobile phone.

Apart from the possibility to view the temperature of every sensor, the user may adjust the pre-set temperature values.

After switching the module on and selecting DHCP option, the controller automatically downloads such parameters as IP

address, IP mask, gateway address and DNS address from the local network. If any problems arise when downloading the

network parameters, they may be set manually. The procedure of obtaining these parameters is described in detail in the

instruction manual of the Internet module.

Online system control via a website is described in detail in section VII.

3. TIME SETTINGS

This option is used to set current time which is displayed in the main screen view.

Use icons: and to set the desired value and confirm by pressing OK.

4. SCREEN SETTINGS

Tapping on Screen settings icon in the main menu opens up

a panel enabling the user to adjust the screen settings to

individual needs.

The user may activate a screensaver which will appear after

a pre-defined time of inactivity. In order to return to the

main screen view, tap on the screen. The following

screensaver settings may be configured by the user:

•Screensaver selection - After tapping on this icon, the user

may deactivate the screen saver (No screensaver) or set the

screensaver in the form of:

- Slide show –(this option may be activated if the photos have

been uploaded first). The screen displays the photos at a

user-defined frequency.

- Clock –the screen displays the clock.

- Blank –after the pre-defined time of inactivity the screen

goes blank.

• Photo upload - Before importing the photos to the controller memory they must be processed using ImageClip (the

software may be downloaded from www.techsterowniki.pl).

After the software has been installed and started, load the

photos. Select the area of the photo which will be

displayed on the screen. The photo may be rotated. After

one photo has been edited, load the next one. When all

the photos are ready, save them in the main folder of the

memory stick. Next, insert the memory stick into the USB

port and activate Photo upload function in the controller

menu.

It is possible to upload up to 8 photos. When uploading

new photos, the old ones are automatically removed from

the controller memory.

• Slide show frequency - This option is used to set the frequency at which the photos are displayed on the screen if the

Slide show is activated.

5. PRENATAL LOCK

Tapping on Parental lock icon in the main menu opens up

a screen enabling the user to configure the parental lock

function. When this function is activated by selecting

Auto-lock ON, the user may set the PIN code necessary to

access to the controller menu.

NOTE

Default PIN code is „0000”.

6. SOFTWARE VERSION

When this option is selected, the display shows the logo of the manufacturer as well as the software version used in the

regulator.

NOTE

When contacting Service Department of TECH company it is necessary to provide the software version number.

7. SERVICE MENU

Service menu functions should be configured by a qualified fitter. Access to this menu is protected with a 4-digit code.

8. FACTORY SETTINGS

This option enables the user to restore factory settings defined by the manufacturer.

9. MANUAL MODE

This function enables the user to check if the contact to which the heating device is connected works correctly.

10. LANGUAGE SELECTION

This option is used to select the software language preferred by the user.

Indice

Altri manuali Tech Controllers Pannello di controllo

Tech Controllers

Tech Controllers EU-M-12 Manuale utente

Tech Controllers

Tech Controllers Sinum CP-04m Manuale utente

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche