Tech21 SansAmp GED-2112 Manuale operativo e di manutenzione

August 2, 2017

SERVICE NOTES for GED-2112

For Qualified Technicians Only

WARNING: No user-serviceable parts inside. Opening and altering the contents within will void the

warranty unless performed by a qualified service technician.

NOTE: The following service notes are recommended as one-time only procedures. It is NOT

recommended to make these changes on a repeated basis.

DESCRIPTION:

The GED-2112 contains two internal jumpers. The first allows the outputs to be tied together so both

channels can be fed through a single output. The second is to configure the operation of the Function

Switch from “mute” to “bypass”.

1. Remove AC cable from unit.

2. Remove bottom cover for access to circuit boards. Carefully unscrew six philips head screws

securing bottom cover to chassis. Be sure to use #2 size screwdriver. Set cover and screws to

the side.

3. Jumpers are located near the FX loop return jack.

TIE JUMPER: The GED-2112 is shipped from the factory with Drive and Deep channels routed through

their respective XLR and ¼” jacks. This configuration is shown in PHOTO 1 below.

PHOTO 1

Moving the jumper to the “TIE” position will combine the Drive and Deep channels to the ¼” and XLR

Drive and Deep output jacks. Please refer to PHOTO 2 below.

PHOTO 2

FUNCTION SWITCH JUMPER: The GED-2112 is shipped from the factory with the Function Switch

operating as a mute button. Please refer to PHOTO 1 on previous page.

Moving the jumper to the “BYPASS” position will send unaffected signal through the ¼” and XLR Drive

and Deep jacks when the Function Switch is disengaged. Please refer to PHOTO 3 below.

PHOTO 3

4. After configuring jumpers to desired positions, replace bottom cover. Be sure not to over-

tighten or strip the six philips head screws.

Indice

Altri manuali tech21 Amplificatore

tech21

tech21 Bass Power Wedge 60 Manuale utente

tech21

tech21 Landmark 600 Manuale utente

tech21

tech21 Trademark 30 Manuale utente

tech21

tech21 Landmark 120 Manuale utente

tech21

tech21 Power Engine 300 Manuale utente

tech21

tech21 Landmark 300 Manuale utente

tech21

tech21 Trademark 60 Manuale utente

tech21

tech21 SansAmp RPM Manuale utente

tech21

tech21 Trademark 10 Manuale utente

tech21

tech21 Trademark 60 Manuale utente

tech21

tech21 Bronzewood 60 Manuale utente

tech21

tech21 SansAmp PSA-1 Manuale utente

tech21

tech21 SansAmp RBI Manuale utente

tech21

tech21 Trademark 60 Manuale utente

tech21

tech21 Trademark 120 Manuale utente

tech21

tech21 VT BASS 500 Manuale utente

tech21

tech21 PW60 Manuale utente

tech21

tech21 SansAmp GT2 Manuale utente

tech21

tech21 Bass Power Engine 60 Manuale utente

tech21

tech21 SansAmp PSA 1.1 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente