TECHLIGHTING Mona Lisa Manuale utente
1.0
Installation Instructions for
Mona Lisa Picture Light
700DEMNLS__
1
920MONA
GP I :ENERAL RODUCT NFORMATION
This product is suitable for indoor dry locations only.
Minimum volume of the electrical box must be 6 cubic
inches (98 cubic centimeter).
MLP LONA ISA ICTURE IGHTS
Installing the Fixture (Canopy Installation)
The picture light bracket should be mounted right above
the electrical box.
Hold the picture light canopy against the electrical box
and mark the bracket holes (1-1/4" apart) on the wall.
With a hammer tap the anchors at the marked points
into the wall up to the threaded portion.
Screw the anchors in the rest of the way with a Phillips
screwdriver.
ELECTRICAL
BOX
ANCHOR
1
2
3
4
1A
34
For canopy installation see section 1.
For plug installation see section 2.
Mount the picture light bracket on the anchors with the
two #8 screws.
#8 SCREW
ANCHOR
1B
5
5
1C
Adjust the picture light height by loosening the two
#6-32 set screws on the front of the picture light
bracket with the 1/16 Allen wrench.
Slide the arms to desired height and tighten the two
#6-32 set screws with the 1/16 Allen wrench.
1/16 ALLEN
WRENCH
#6-32
SET SCREW
BRACKET
FIXTURE ARMS
6
7
6
7
2
1F
Mount the canopy to the electrical box with the two
long #8-32 screws.
NOTE: Before making electrical connections, use the
provided universal round crossbar if the canopy
holes do not line up with the electrical box holes.
LONG #8-32
SCREW
CANOPY
15
15 15
1E
Connect the black driver wire to the hot power line wire
with a wire nut.
Connect the white driver wire to the neutral power line
wire with a wire nut.
Connect the fixture to a suitable ground in accordance
to local electrical codes.
Place the driver, all wires, and wire nut connections into
the electrical box.
DRIVER
13
14
11
12 13
14
11
12
1D
Connect the fixture cords to the fixture arms.
Feed the fixture cords through the canopy, then place
the canopy against the electrical box and determine
wanted length of cord.
Once wanted length has been determined, trim the
cords leaving enough to make electrical connections.
8
9
CANOPY
ELECTRICAL BOX
FIXTURE ARMS
FIXTURE CORD
10
9
8
10
Hang the picture wire in the picture hanging slot on the
picture light bracket.
SKIP TO SECTION 3
PICTURE
HANGING SLOT
PICTURE WIRE
1G
16
PICTURE LIGHT
BRACKET
PICTURE
4" CANOPY
16
3
Choose a place on the cord where the switch is to be
mounted.
With a sharp knife cut about a 1" slot in the cord web.
Make sure not to nick the insulation on either wire.
Cut the smooth wire in half.
WIRE WEB
SMOOTH WIRE
1"
RIDGED WIRE
2D
7
8
9
9
8
UPPER HALF OF THE SWITCH
SHARP
POINTED
PRONG
LOWER HALF OF
THE SWITCH
NUT
SMOOTH WIRE
RIDGED WIRE
SHARP
POINTED
PRONG
Loosen the screw on upper half of the switch to remove
the nut on the lower half.
Place the cord in the lower half of the switch (the half
without the wheel). The cut wire runs through the
center of the switch.
Press both halves back together. Replace the nut in the
lower half and tighten the screw on upper half so that
the sharp pointed prongs in upper half of the switch
pierce the wire insulation and make contact inside.
2E
10
11
12
10
11
12
Installing the Fixture (Plug Installation)
Hold the picture light against the wall and mark the
bracket holes (1-1/4" apart).
With a hammer tap the anchors at the marked points
into the wall up to the threaded portion.
Screw the anchors in the rest of the way with a Phillips
screwdriver.
Mount the picture light bracket on the anchors with the
two #8 screws.
#8 SCREW
ANCHOR
2
4
3
ANCHOR
2A
2B
1
2
3
4
1/16 ALLEN
WRENCH
FIXTURE ARMS
BRACKET
5
6
#6-32
SET SCREW
2C
Adjust the picture light height by loosening the two
#6-32 set screws on the front of the picture light
bracket with the 1/16 Allen wrench.
Slide the arms to desired height and tighten the two
#6-32 set screws with the 1/16 Allen wrench.
5
6
4
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
847.410.4400
www.techlighting.com
© 2013 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is
a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right
to change specifications for product improvements without notification.
A Generation Brands Company
3A
Determine wanted light direction and set by tilting the
handle bar up or down.
1
CAUTION: Fixture will be hot. Do not touch any
other surface of the fixture. Only use handle bar to
tilt the lamp and change light direction.
HANDLE BAR
Use the provided cable clips onto the wall to dress the
cord.
CABLE CLIP
PICTURE
HANGING SLOT
PICTURE WIRE
PLUG-IN
TRANSFORMER
SWITCH
PICTURE
CABLE CLIP
CABLE CLIP
Hang the picture wire in the picture hanging slot on the
picture light bracket.
Plug the transformer to the 120 volt power outlet.
PICTURE LIGHT
BRACKET
2G
2H
14
15
16
15
16
Adjusting the Head
14
FIXTURE ARM
FIXTURE CORD
2F
Connect the fixture cords to the fixture arms.
13
13
NOTE: The handle bar may be removed for aesthetic
purposes. After setting light direction, remove the
handle bar by unscrewing it counterclockwise.
Altri manuali TECHLIGHTING Attrezzatura di illuminazione
TECHLIGHTING
TECHLIGHTING tiella Sola Pack Manuale di istruzioni
TECHLIGHTING
TECHLIGHTING Element CMH MR16 Manuale utente
TECHLIGHTING
TECHLIGHTING ELEMENT E3-L AE Series Manuale utente
TECHLIGHTING
TECHLIGHTING ELEMENT E6_LO-C_N Series Manuale utente
TECHLIGHTING
TECHLIGHTING Cirque Small 700CQS Manuale utente
TECHLIGHTING
TECHLIGHTING UNILUME 700UCRD Series Manuale utente
TECHLIGHTING
TECHLIGHTING T-trak 700TTSCCADJ Series Manuale utente
