Techno CNC Systems HD II Tabletop Manuale utente
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 1
HD II Tabletop Manual
NK105G2
Techno CNC Systems, LLC ©2018
This document will provide a quick guide to the set up and operation of the Techno HD II Tabletop
CNC Router equipped with the NCstudio controller.
Tabletop CNC
Router Manual
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 2
HD II Tabletop Manual
NK105G2
TABLE OF CONTENTS
Safety Instructions .............................................................................................................................................................. Page 3
Colleting Guidelines .............................................................................................................................................................. Page 4
l HD II Tabletop Quick Setup .......................................................................................................................................... Page 5
Control Panel Functions and Enabling the Machine...........................................................................................Page 6
II HD II Tabletop Start Up .......................................................................................................................Page 7
Functions of the Keys ......................................................................................................................................... Page 8
Shift Commands / Combination Keystrokes ......................................................................................... Page 9-11
III Operating Tutorials
3.0- Switching Movement to Step or Jog
3.1- Jogging the Machine and Changing from High/Low Jog Speed
3.2- Stepping the machine .............................................................................................. Page 12
3.3- Modifying the Jog Speed and Step Size
3.4- Feedrate Override ................................................................................................................... Page 13
3.5- Adjusting the XYZ Position/WCS/User Origin .................................................................... Page 14
3.6-LoadingaG-codele ...................................................................................................................Page15
3.7- Running a G-code File ............................................................................................... Page 15
IV Advanced Tutorials
4.1- Alternating between Override Page .................................................................Page 16
4.2- Programmed Feedrates .................................................... Page 16
4.3- How to use all 6 work coordinates ............................................................................................. Page 17
4.4- How to use select line number function ......................................................................... Page 18
Using the 4th Axis .............................................................................................................................................. Page 19
SettingOverridespeedforaG-codele....................................................................................Page20
NotesontheG-codeleAccelerationSet.....................................................................................................Page21
Appendix
HD II Tabletop Settings ................................................................................................................................................ Page 21- 26
Machine Lubrication ................................................................................................................................................................ Page 27
Maintenance / Problem/Solutions ............................................................................................................................. Page 28
Controller Diagram .................................................................................................................................................................... Page 29
Warranty ...................................................................................................................................... Page 30
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 3
HD II Tabletop Manual
NK105G2
1. Keepngers,hands,andallotherobjectsawayfrom
machine while power is on.
2. Disconnect power to all system components when
not in use, when changing accessories, and before
servicing.
3. Do not loosen, remove, or adjust machine parts or
cables while power is on.
4. Exercise care with machine controls and around
keyboard to avoid unintentional starting.
5. Make sure voltage supplied is appropriate to
specicationsofcomponents.
6. Machines must be plugged into three-pronged
grounded outlets. Do not remove the grounding
plug or connect into an ungrounded extension
cord.
7. Keep cables and cords away from heat, oil, and
sharp edges. Do not overstretch or run them
under other objects or over work surfaces.
8. Useproperxturesandclampstosecurework.
Never use hands to secure work.
9. Do not attempt to exceed limits of machine.
10. Do not attempt to use machine for purposes other
than what is intended.
11. Use machine only in clean, well-lit areas free from
ammableliquidsandexcessivemoisture.
12. Stay alert at all times when operating the machine.
13. Always wear safety goggles.
14. Donotwearloose-ttingclothingwhenoperating
machine. Long hair should be protected.
15. Always maintain proper balance and footing when
working around the machine.
16. Maintain equipment with care. Keep cutting
tools clean and sharp. Lubricate and change
accessories when necessary. Cables and cords
should be inspected regularly. Keep controls
clean and dry.
17. Before using, check for damaged parts. An
authorized service center should perform all
repairs. Only identical or authorized replacement
parts should be used.
18. Remove any adjusting keys and wrenches before
turning machine on.
19. Do not operate the machine unattended.
20. Follow all safety instructions and processing
instructions in the MSDS for the material being
processed.
21. Use proper precautions with dust collection
systemstopreventsparksandrehazards.
22. Makesuretohaveproperreextinguishing
equipment on hand at all times.
WARNING: IMPROPER OR UNSAFE OPERATION OF THE MACHINE WILL RESULT IN
PERSONAL INJURY AND/OR DAMAGE TO THE EQUIPMENT.
READ THESE INSTRUCTIONS THOROUGHLY BEFORE OPERATING MACHINE. DO
NOT OPERATE MACHINE IF YOU ARE UNFAMILIAR WITH THESE SAFE OPERATING
INSTRUCTIONS. DO NOT OPERATE MACHINE WITHOUT KNOWING WHERE THE
EMERGENCY STOP SWITCH IS LOCATED.
PREVENT FIRE HAZARDS by using the proper feeds, speeds, and tooling while operating your
Techno machine. For example, setting feeds and speeds too low and/or using dull tool bits creates
friction at the material.The friction generates heatwhich can result in a re that can be drawn
through the vacuum table or dust collector without warning. Fire hazard from friction heating caused
by dull tools is possible when cutting certain materials, especially composite material such as wood
composites, MDF and Particleboard. © 2012
Safety Instructions
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 4
HD II Tabletop Manual
NK105G2
WARNING!
THE SPINDLE WILL BE DAMAGED
IF UNBALANCED EQUIPMENT IS USED.
AIR SUPPLY MUST BE FILTERED AND DRY.
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 5
HD II Tabletop Manual
NK105G2
1.1 - The electronics are housed in the
controller cabinet located at the back of the
machine displayed in Figure 1.1. The controller
box may have to be moved or handled during
the unpacking of the machine. For shipping
purposes, the controller box may have been
moved forward.
I. Techno HD II Tabletop Quick Set up
1.2 - Have a licensed electrician connect power to the
controller. The machine requires 220V single phase 15amp
power in order to operate. Plug the power cable into the
rearofthemachineasshowningure1.2.The10ftpower
cable supplied must be hardwired to the power source.
Fig. 1.1 Fig. 1.2
Fig. 1.3
The cable provided will be one of two types: brown, blue, and green/
yellow wire or a cable with a black, white, and green wire. (Fig 1.3)
Power is connected as follows:
Green or Green/Yellow conductor is always ground .
The two other conductors will be the hot leads.
Connecting the Power
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 6
HD II Tabletop Manual
NK105G2
1.6 Enabling The Machine.
First make sure the Emergency Stop is not pressed by giving it a ¼ turn
clockwise. Then, activate the machine by pressing the green POWER but-
ton. Power is now applied to the machine. The green light will illuminate.
Emergency
Stop
Power
Enable
Power
Disable
Spindle VFD
Readout
USB
Port
IF EQUIPPED WITH SAFETY ENCLOSURE,
CHECK E-STOP ON THE FRONT OF THE
MACHINE NEAR THE DOOR!
Control Panel Functions
Latch
to open
controller
box
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 7
HD II Tabletop Manual
NK105G2
Whenthemachinerstpowerson,
the display on the controller will light
up and say “Starting System”. (Fig. 2.1a)
Once the system has booted it will ask
the user “Back to reference point?” Fig
2.2b
Fig. 2.1a Fig. 2.2b
Thisisalsoknownas‘homing’themachine.Itreferstotheprocessofthemachinendingitsmechanical
home position.
From this point, the user has two options;
Home the machine or cancel the homing process. We recommend that you home the machine every time
you start up.
Press “ESC” will skip the homing process.
WARNING:Therewillbenoreferencepositionandbreakpoints,osetsandallfunc-
tions that rely on a reference position will be invalid.
Once the machine has moved to its homing position on each axis, it will stop and enter an IDLE state and
will be ready to use.
Pressing“OK”willinitiatethehomingprocess.ThemachinewillrstmovetheZ-axis
to the top of travel and then the X and Y axis will move simultaneously until both are
at the home / reference position at the front left corner of the machine bed.
NOTE: The homing procedure can be aborted at anytime by pressing ESC.
ADVANCED HOMING:
If you hit “ESC” by accident, or would like to reindicate the axes, there are two ways to “Home” again.
1) Press Menu > 3. Operations > 1. Back REF Point > 1. All Home
2) Shortcut
+
II. HDII Tabletop Startup
Main Screens:
This picture shows that the machine has been homed
due to the X* Y* Z* symbols
This picture shows that the machine has not been
homed due to the X Y Z symbols (there are no *s next to
the symbols)
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 8
HD II Tabletop Manual
NK105G2
Single Keystroke Functions on the Handheld Pendant
Positive Feedrate
Override
(Input the number 7)
X- Movement
(Input the number 4)
Jog Speed Select
(Input the number 0)
Enter Manual Parameters
Screen
Change high/low speed
and XYZ step increment
Z+ Movement
(Input the number 9)
X+ Movement
(Input the number 6)
Z- Movement
(Input the number 3)
Menu Screen
(Input a decimal point)
Shift Key
Switch between
Jog and Step
modes
Down
Directional
Key
Set XY Zero Position
(Input a minus sign)
Stop
Cancel
Escape
Up Directional
Key
Pause
Start key
SpindleOn/O
(Input the number 5)
Negative Feedrate
Override
(Input the number 1)
Y+ Movement
(Input the number 8)
Y- Movement
(Input the number 2)
OK
Select
Yellow Keys are movement related
Blue Keys are speed and feed related
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 9
HD II Tabletop Manual
NK105G2
Increase feedrate override; input the number 7
Move Y axis in the positive direction (rear of table); input the number 8
Move Z axis in the positive direction (top of travel); input the number 9
Move X axis in the negative direction (left of table); input the number 4
Manuallyturnspindleon/o;inputthenumber5
Move X axis in the positive direction (right of table); input the number 4
Decrease feedrate override; input the number 1
Move Y axis in the negative direction (front of table); input the number 2
Move Z axis in negative direction (bottom of travel); input the number 3
Toggle between manual jog high/slow speeds; input the number 0
Set XY=0 point (XY origin); input a minus sign
Open the main menu; input a decimal point
Call: 1-631-648-7481 or Visit:: www.technocnc.com/technical-support/ 10
HD II Tabletop Manual
NK105G2
Start machining
Pause machining; Up direction arrow when navigating menus
Stop machining; Cancel; Escape
Switch between jog and stepping modes; Auxilliary key
Down direction arrow when navigating menus
OK; Select; Open manual jog/step adjustment screen
Indice
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza