Technoline WS 6730 Manuale utente

WS 6730 Instruction manual

Main UnitAppearance

Part A- LCD

A1: Radio Controlled Icon A2: Date

A3: Weather Forecast A4: Past Hour (Pressure History)

A5: Barometric Pressure Bar Graph. A6: Indoor Temperature and Humidity

A7: Outdoor Temperature and Humidity

A8: Radio Controlled Time Display A9 : Day of Week

A10: Barometric Pressure Trend A11: . Barometric Pressure Reading

A12: Selected Outdoor Channel

Part B- Buttons

B1: “MODE/SET” button B2: “SNOOZE/LIGHT “ button

B3: “AL ON/OFF” button. B4: “CHANNEL “ button

B5: “ALERT” button B6: “HISTORY” button

B7: “+(12/24)” button B8:” IN MEN” button

B9: “▲” button B10: ”▼In C/F ” button

B11: ” - C/F / ” button B12: “OUT MEN” button

B13: “RESET” button

Part C- Structure

C1: Wall Mount Hole C2: Battery Compartment

C3: Stand.

Thermo & Hygro Sensor Unit’s Appearance.

D2: Outdoor Temperature D1: Transmission Indication LED

D3: Wall Mount Hole D4: °C/°F” button

D5: Channel Selecting Switch D6: “TX” button

D7: Battery Compartment D8: Stand

Set Up:

yInsert batteries.

yUse a pin to press the RESET (B13) button

Weather Forecast Function:

zAfter Batteries inserted, or holding “HISTORY” button (B6) for 3 seconds, Pressure Reading’s digits

flashes(A3). Enter the height,in meter, of the Main Unit above sea level by pressing “▲“ (B9) or

“▼“ (B10) buttons. Press “HISTORY” button (B6) to confirm the setting. After entered the height, the

Pressure Reading shows the Barometric Pressure at the sea level. The weather forecast may not

be accurate if the height entered is not correct.

zThe current weather status should be entered again if the altitude of the Main Unit is changed.

( Barometric pressure is lower at higher altitude location. Therefore, altitude change will affect the

weather forecast)

zTotally 5 different weather condition in the weather forecast.

“ ” means Sunny .

“ ” means Slightly Cloudy.

“” means Cloudy.

“” means Rainy

“” means Cloudburst.

zIf there is any inconsistency of weather forecast between Local Weather Station and this unit, the

Local Weather Station's forecast should prevail. We will not held responsible for any trouble that

may come up due to wrong forecasting from this unit.

zThe trend pointer (LCD A10) indicates the trend of the barometric pressure.

“” indicates the barometric pressure trend is increasing.

“” indicates the barometric pressure trend is steady.

“” indicates the barometric pressure trend is decreasing.

Barometric Pressure Meter

Press “HISTORY” button (B6)

zHold “ ▲” button (B9) for three seconds to select the unit for Barometric Pressure reading in inHg or

mb / hPa.

zPress “ HISTORY” button (B6) to view the past 12 hour Barometric Pressure history.

The hour is indicated on the LCD.

0 HR = Current Barometric Pressure Reading

-1HR = Barometric Pressure Reading in 1 hour ago

-2HR = Barometric Pressure Reading in 2 hour ago ……..etc

Outdoor Thermo Sensor Unit Registration Procedure:

zThe main unit automatically starts receiving transmission from Outdoor Thermo and humidity

Sensor after Battery inserted. Outdoor digits (A7) blinks.

zInsert the batteries in the Thermo Sensor Unit. The sensor unit automatically transmit temperature

to the main unit. ( Battery compartment (D7) of thermo sensor is located behind the back cover,

unscrews to open.)

zFor having more than one external transmitter (Maximum3), select the Channel, CH1, CH2 or CH3

to ensure each sensor is transmitting at difference channel before inserting batteries. The channel

selecting switch (D5) is at the back of the thermo sensor unit.

zPress “ TX “ button (D6) on the thermo sensor unit to transmit temperature to the main unit

manually. The main unit gives a “beep” sound if it received the temperature.

Display Outdoor Temperature :

zPress “ CHANNEL” button (B4) to view the 3 Channels. The sequence is shown as follow:

Press Press Press

“CHANNEL” button “CHANNEL” button “CHANNEL” button

Display the three channels alternatively

zHold “ CHANNEL” (B4) button for 3 seconds to cancel unused channel. It will automatically register

a new channel again if a new channel is received.

If there is no temperature displayed in existing channel ( “ - - . –“ is displayed on the LCD ), hold

“CHANNEL” button (B4) for 3 seconds to cancel that channel and receive the channel again

(“Beep” sound can be heard.) Then, press “ TX “ button (D6) on the thermo sensor unit to transmit

signal to the main unit manually

zThe trend pointer displayed indicates the trend of the outdoor temperature.

“” indicates the outdoor temperature is increasing.

“” indicates the outdoor temperature is steady.

“” indicates the outdoor temperature is decreasing.

zPress “ °C /°F” button (D4), on the Thermo Sensor unit, to select Temperature to be displayed in

Celsius mode or Fahrenheit mode.

Maximum/Minimum Temperature/Humidity recording function:

zPress “IN MEN” button (B8) to show the maximum or minimum of indoor temperature/humidity.

Press “OUT MEN” button (B12) to show the maximum or minimum of outdoor temperature/humidity.

“” is shown on the LCD if maximum temperature/humidity is shown.

“ ” is shown on the LCD if minimum temperature/humidity is shown.

yHold “IN MEN” button (B8) or “OUT MEN” button (B12) for 3 seconds to clear the recorded

maximum and minimum reading.

Temperature Alert function:

zHold “ ALERT” button (B5) for 3 seconds to enter Temperature Alert setting, Temperature’s digits

flash.

zPress “ +” (B7) or “-” (B11) button to select Indoor or Outdoor CH1, CH2 and CH3 temperature alert.

Press “ALERT” button (B10) to confirm the setting.

zPress “ +” (B7) or “-” (B11) button to set the upper ” ” and lower “ ” limit of the temperature.

Press “ALERT” button (B5) to confirm the setting.

zPress “ ALERT” button (B5) to set the Temperature Alert function on or off ( “ ” appears on the

LCD if this function is on).

Radio Controlled Clock:

zAfter registered new channels or press “CHANNEL” button (B4) to stop scanning, the clock will then

scan the DCF time signal ( “ ” flashes on the LCD ). Buttons will not function while scanning

for DCF or Thermo sensor’s signal unless they are well received or stopped manually.

zThe clock automatically scans the time signal at 3.00 a.m. everyday to maintain accurate timing.

For failed reception, scanning stops ( “ ” on the LCD disappear ) and repeats again at 4.00

a.m. 5.00a.m. and 6.00a.m.

zThe clock manually scans the time signal by holding “ - ” button (B11) for 3 seconds. For failed

reception, scanning stops. ( “ ” on the LCD disappear ).

zHold “-” button (B11) for 3 seconds to stop scanning when receiving DCF signal.

“” flashes indicate now is receiving DCF signal

“” turns on indicate signal received successfully

zDST is shown on the LCD is it is in Daylight Time Saving Mode

Manual Time Setting:

zHold “ MODE/SET” button (B1) for 3 seconds to enter Clock/Calendar setting Mode .

zPress “+” (B7) or “-” (B11) buttons to adjust the setting and press “MODE” (B1) button to confirm

each setting.

zThe setting sequence is shown as follow: Hour, Minutes, Second, Year, Month/Day sequence,

Month, Day, Time Zone, Day-of-week language.

z8 languages can be selected in Day-of-week, they are: German, English, Russian, Denmark, Dutch,

Italian Spanish and French,. The languages and their selected abbreviations for each day of the week

are shown in the following table.

Language

Sunday

Monday Tuesday Wednesday Thursday Friday Saturday

German, GE SO MO DI MI DO FR SA

English, EN SU MO TU WE TH FR SA

Russian, RU BC NH BT CP HT NT CY

Denmark, DA SO MA TI ON TO FR LO

Dutch, NE ZO MA DI WO DO VR ZA

Italian, IT DO LU MA ME GI VE SA

Spanish, ES DO LU MA MI JU VI SA

French, FR DI LU MA ME JE VE SA

zThe Time zone is used for the countries where can receive the DCF time signal but the time zone is

different from the German time.

zWhen the country time is faster than the German time for 1 hr, the zone should be set to +1. Then

the clock will automatically set 1 hour faster from the signal time received.

12/24 Hour Display mode:

yPress “ +12/24” button (B7) to select 12 or 24 hours mode.

Snooze Alarm Clock Function:

zPress “ MODE/SET” button (B1) to select to view:

Time Alarm Time1 (“ “ Shown on the LCD) Alarm Time 2 (“ “ Shown on the LCD)

zWhen viewing Alarm Time 1 or Alarm Time 2, hold “MODE/SET” button (B1) for 3 seconds to enter

that Alarm Time setting. Press “ +” (B7) or “-” (B11) buttons to adjust the alarm time.

zWhen viewing Alarm Time 1 or Alarm Time 2, press “AL ON/OFF” (B3) button to switch that alarm

on or off. If it is on, “ ” or “ ”shown on the LCD.

zPress “SNOOZE” (B2) button when alarming . The alarm will snooze for 5 minutes, then it alarms

again. This snooze function can be enabled for maximum 7 times.

zPress “MODE/SET” (B1) or “AL ON/OFF” (B3) button to stop the snooze alarm.

Low Batteries Indicator:

yLow battery icon “ “ appear at outdoor temperature row in particular channel indicating that

Thermal Sensor Unit of the channel is in low battery status. The batteries should be replaced..

Note:

zUse a pin to press the reset button (B13) if the Unit does not work properly.

zAvoid placing the clock near interference sources/metal frames such as computer or TV sets.

zThe clock loses its time information when the battery is removed.

zButtons will not function while scanning for DCF or thermo sensor’s signal unless they are well

received or stopped manually.

Altri manuali Technoline Stazione meteorologica

Technoline

Technoline WS9050 Manuale utente

Technoline

Technoline WS9251 Istruzioni per l'installazione

Technoline

Technoline WS 6830 Manuale utente

Technoline

Technoline WS6767 Manuale utente

Technoline

Technoline WS 9422 Manuale utente

Technoline

Technoline WS-9632-IT Manuale utente

Technoline

Technoline WS 6720 Manuale utente

Technoline

Technoline WS 9274 Manuale utente

Technoline

Technoline WS 6750 Manuale utente

Technoline

Technoline WS1900 Manuale utente

Technoline

Technoline WS8014 Manuale utente

Technoline

Technoline WS6620 Manuale utente

Technoline

Technoline WS 6715 Manuale utente

Technoline

Technoline WS 6502 Manuale utente

Technoline

Technoline WS 9218 Manuale utente

Technoline

Technoline WS 6760 Manuale utente

Technoline

Technoline WS 9257-IT Manuale utente

Technoline

Technoline WS9470 Manuale utente

Technoline

Technoline WT 221 Manuale utente

Technoline

Technoline WS 9172 Manuale utente

Technoline

Technoline WS6442 Manuale utente

Technoline

Technoline WS6850 Manuale utente

Technoline

Technoline DCF-77 Manuale utente

Technoline

Technoline WS 9257 Manuale utente

Manuali Stazione meteorologica popolari di altre marche

Auriol

Auriol AHFL 433 A1 Manuale utente

NexSens

NexSens G2-HYDROMET Manuale utente

Hyundai

Hyundai WS 2202 Manuale utente

IROX

IROX HBVR761 UV-X Manuale utente

La Crosse Technology

La Crosse Technology C86371 Manuale utente

ADE

ADE WS 1711 Manuale utente

Auriol

Auriol z29592 Manuale utente

Auriol

Auriol 296289 Manuale utente

Hyundai

Hyundai WS 2266 Manuale utente

La Crosse Technology

La Crosse Technology WS-2210 Manuale utente

La Crosse Technology

La Crosse Technology WS-811561 Manuale utente

Ventus

Ventus W177 Manuale utente

National Geographic

National Geographic VA Colour RC Manuale utente

Renkforce

Renkforce 1208067 Manuale utente

Levenhuk

Levenhuk Discovery Report WA40 Manuale utente

Instant Transmission

Instant Transmission MA 10410 Manuale utente

Lutron Electronics

Lutron Electronics PHB-318 Manuale utente

WAREMA

WAREMA EWFS Weather station eco Manuale utente