Techpro IP-EL Series Manuale utente
Guaranteed
Warranty
4K
Resolution
IP-EL Series - User's Manual
Motion
Activated
Recording
PTZ
Control View From
Anywhere
Welcome
Thank you for purchasing our IP camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product! Please keep
this user’s manual well for future reference!
Important!
DO NOT Connect all the cameras on the same network at the same time.
This will cause IP conflict within your network and you will not be able to
accress your cameras. Before connecting all the of the IP cameras on the
network One-At-A-Time.
DO NOT power the camera with both PoE and a power supply at the
same time.
If you purchase a PoE(Power Over Ethernet) device from us, Whether
as an External POE Switch or built into on of our NVRs, your camera
will be powered through the Ethernet cable and will not need to power it
with a seperate power supply.
*Restrictions may apply*
Our units do not support PAL
To find your cameras on the network, use the "config Tool" found in the
CD(under Software>ConfigTool) that came with your package. Some
cameras will be assigned as a DHCP. Therehore, The "IP Config Tool is
required to find the camera on the network.
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1.This series product supports PoE too. Please note:
Do not connect these two power supplying sources to the device at the same time; it may result
in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name Amount
IP Camera Unit 1
CD 1
Installation Accessories Bag 1
Table of Contents
1General Introduction ..................................................................................................................
1.1 Overview........................................................................................................................
1.2 Features.........................................................................................................................
2Structure ......................................................................................................................................
2.1 Multiple-function Combination Cable ........................................................................
2.2 Framework and Dimension.........................................................................................
4Quick Configuration Tool...........................................................................................................
4.1 Overview.........................................................................................................................
4.2 Operation.......................................................................................................................
5FAQ .............................................................................................................................................
Appendix Toxic or Hazardous Materials or Elements ................................................................
1.3Camera Installation.......................................................................................................
1.4 Varifocal lens...................................................................................................................
1 General Introduction
1.1 Overview
This series IP camera integrates the traditional camera and network video technology. It adopts video
data collection, transmission together. It can connect to the network directly without any auxiliary
device.
This series IPC uses standard H.264 video compression technology, which maximally guarantees the
video quality.
It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The waterproof design conforms to the IP 66 level. It has the sound waterproof function suitable for
use in the outdoor environments.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this
series IPC is widely used in many environments such as an office, bank, road monitor and etc.
1.2 Features
User
Management
zDifferent user rights for each group, one user belongs to one group.
zThe user right shall not exceed the group right.
Storage
Function
zSupport central server backup function in accordance with your configuration
and setup in alarm or schedule setting
zSupport record via Web and the recorded file are storage in the client-end
PC.
zSupport network storage function such as FTP.
Network
Monitor
zIPC supports one-channel video data transmit to network terminal and then
decode. Delaying time is within 270ms (network bandwidth support needed)
zMax supports 20 connections.
zAdopt the following video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
zSupport web access.
Network
Management
zRealize IPC configuration and management via Ethernet.
zSupport device management via web or client-end.
Power
zExternal power adapter DC 12V.
zSupport PoE.
Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!
Assistant
Function
zLog function
zSupport system resource information and running status real-time display.
zDay/Night mode auto switch.
zSupport picture parameter setup such as electronic shutter and gain setup.
zSupport motion detect.
zBacklight compensation: screen auto split to realize backlight compensation
to adjust the bright.
zSupport video watermark function to avoid vicious video modification.
zBuilt-in IR light. Support IR night vision.
zThe enclosure conforms to the IP 66 protection. Has the waterproof function.
Step 1
If included please take the installation position map from the accessories bag,
and then paste it on the ceiling or the wall according to your monitoring area
requirements. Draw and then drill holes in the installation surface and then insert
expansion(anchor) bolts in the holes. Secure these bolts firmly.
Step 2
Turn counter clockwise to remove the decoration ring(plastic housing), turn the
pan base to the pedestal to loosen or secure firmly(metal housing) or Use the
inner hex wrench to remove the three enclosure fastening screws and then
remove the dome enclosure(glass enclousure). Adjust the pedestal position
according to the cable exit move(ceiling/side). Pull the cable through the cable
side exit at the installation surface and the pedestal.
(Please skip this step if you are mounting on a ceiling). Line up the screw holes
at the bottom of the pedestal to the expansion bolts in the installation surface.
Put three self-tapping screws to expansion bolts and then secure firmly. Now the
pedestal is on installation surface.
Ceiling or Wall
Expansion Bolt
Dome Camera Body
ST3 Self-tapping Screws
Decoration Ring
Plastic Housing
Dome Installation
1.3 Camera Installation
Ceiling orWall
Expansion Bolt
ST3 Self-tapping Screws
Pedistal 1
Metal Housing
Ceiling orWall
Installation Position Map
Expansion Bolts
Enclosure fastening screw
Socket Screw
Inner Hex Wrench
Glass Enclosure
Box Camera Lens Installation
Auto Aperture Lens
Please follow the steps listed below for auto aperture lens installation.
Remove the CCD protection cap of the device, and then line up the lens to
the proper installation position. Turn clockwise until the lens is fixed firmly.
Insert the lens cable socket to the auto lens connector in the side panel.
Adjust focus length.
Before you install the bracket, please pull the cable through the cable exit of the bracket
chassis.
Sun Shield Cover
Bracket
Bullet Installation
Important
The installation wall shall min sustain 3X weight of the bracket and camera.
Step 1
Paste the installation map on the surface of the wall or the ceiling.
Step 2
Dig the installation holes according to the installation map.
Indice
Altri manuali Techpro Telecamera di sicurezza
