Tecnoinox PCR12E7 Manuale utente

PCR12E7

6 ROUND ERMETIC HOT PLATES ELECTRIC BOILING TOP (DIAM 22CM - 8.7IN)

716004

CODE

DESCRIPTION

MODEL

13-03-2023 12:06

EN - 1

5410.256.08

Part 1 – Installation

COOK TOPS AND ELECTRICAL COOKERS WITH ELECTRIC OVEN

General warnings

The manufacturer declines any liability

for damage caused by improper or incorrect

appliance installation or maintenance, or

failure to observe the safety regulations.

The appliance referred to in this

instruction manual has been manufactured

in conformity with the requirements of the

European Directives on Low Voltage and

Electromagnetic Compatibility.

The appliance must be installed by a

qualified technician according to the

regulations and directives in force in the

country of use, following the instructions in

this manual.

The appliance can operate with a

50Hz or 60Hz power supply without

modifying the wiring or the internal

components. Please see the technical data

on the rating plate for the voltage.

This appliance has been designed

exclusively to cook food in professional

kitchens such as those in restaurants,

canteens and hotels. This appliance is not

designed for mass, continuous food

production. All other uses are considered

improper.

The appliance must never be left

unattended when it is being used.

The appliance must be installed so as

to prevent water from coming into contact

with the cooking plate.

The appliance is designed for

professional use and therefore should only

be used by qualified personnel.

Be careful when using the appliance

because the cooking surfaces are very hot.

The appliance should be installed

under an extractor hood for evacuating

cooking vapours.

Install the appliance on a floor or flat

surface. Avoid slopes of more than 5° to keep

it stable.

Whenever the appliance is moved, for

example to be transported, written off and

scrapped, take care not to tilt the appliance

more than 5° to keep it stable.

The appliance, and especially the

power lead, must not be installed anywhere

near heat sources.

Disconnect devices must be

incorporated into the fixed wiring, in

accordance with wiring guidelines.

The temperature of the environment

in which the appliance is installed must not

exceed 50°C.

Do not open the control panel or

touch the electrical components. Contact

the technical support service.

If the power cable is damaged it must

be replaced by the manufacturer, technical

support, or a similarly qualified person, in

order to avoid any hazards.

Switch the appliance off during

maintenance or when parts are being

replaced.

When using the appliance, wear oven

gloves and clothing that covers the entire

body.

The floor around the appliance may

become slippery.

Switch the appliance off in the event of a

fault or malfunction.

Please be extremely careful and

contact the technical support service if any

parts or components come loose.

The oven should also be checked

once a year by a qualified technician.

EN - 2

5410.256.08

The surfaces in contact with the

appliance must be covered with heat-

insulating material.

To prevent accidental contact with

hot parts, fit the 2 thermal protection plates

(labelled Bin the figure below) on the sides

of the cooking top. Follow the relevant

instructions to fit them. The thermal

protection side plates are provided, and can

also be ordered at a later date.

For Australia and New Zealand only:

the fixed system must be equipped with a

protective device compliant with standard

AS/NZS 3000.

If the appliance is installed in line:

Respect the minimum clearance

distance of 80 mm between the appliance

and any walls made of flammable material,

partitions, kitchen furniture or nearby

equipment.

For cook tops installed on the work

surface:

For models 800 mm wide or less only,

fix the feet in position respecting a

minimum clearance distance of 80 mm from

any walls made of flammable material,

partitions or nearby equipment.

For cook tops installed on their own, on

the floor and separate from other

equipment:

For models 800 mm wide or less only,

to ensure electrical appliances positioned

on the floor are vertically stable, fix a bracket

to the floor to anchor the appliance down

(labelled Ain the figure below). Follow the

relevant instructions to fit them. The bracket

is provided, and can also be ordered at a

later date.

Electrical connections

Remove the appliance packaging as well as the protective plastic sheet. If

necessary, remove any traces of glue with a suitable solvent. Please

comply with local legal provisions when disposing of the packaging.

When installing the appliance, please observe the following regulations:

applicable laws in force;

European, national, regional and/or local regulations;

directives and regulations stipulated by the local electricity supplier;

accident-prevention regulations in force;

fire-prevention regulations.

Before connecting the electrics, take note of the technical

specifications such as voltage, frequency, number of phases and

power required for installation. This information can be found on

the appliance data plate.

EN - 3

5410.256.08

Power supply features:

The alternating current power supply to the appliance must meet

the following conditions:

Maximum voltage variation ± 10%

Maximum frequency change ± 1% in continuous ± 2% for a

short period of time.

The appliance power supply must be protected against

overcurrent (short circuits and overload) with fuses or properly

sized circuit breakers.

The installer must connect up the appliance by positioning an

easily accessible main switch that disconnects all poles supplying

electrical power to the appliance. When contacts are open, there

must be a minimum distance of 3 mm between the poles.

The cable:

must not be installed near heat sources and the ambient

temperature of the surrounding environment must not exceed

50°C;

must be protected by a rigid metal or plastic tube;

must meet H07 RN-F standards as a minimum;

must have a minimum cross section as indicated on the cover.

In reference to figure 1, to access terminal board “M”, remove the

control panel by loosening the screws on the panel. Connect the

power cable wires to the terminal board by following the

instructions provided in the wiring diagram.

The appliance must be connected to an efficient earth. Connect the earth

conductor to the screw marked with the symbol “ ” close to the

connection terminal board. Be careful to pass the cable through the “P”

cable gland near the terminal board; keep the cable laid flat on the bottom

and fix it with the “ ” cable clamp. The appliance must also be included in

an equipotential bonding system. This connection is made using a screw

marked with the symbol.

The equipotential wire must have a cross section of 10 mm2.

The manufacturer declines any liability

for damage caused by improper or incorrect

appliance installation or maintenance, or

failure to observe the safety regulations.

EN - 4

5410.256.08

Part 2 – Use

General warnings

The appliance is designed for

professional use and therefore should only

be used by qualified personnel.

Be careful when using the appliance

because the cooking surfaces are very hot.

The appliance must never be left

unattended when it is being used.

Switch the appliance off in the event

of a failure or malfunction.

Be careful when using the appliance

because the cooking surfaces are very hot.

The plates are provided with a

temperature limiter that stops the electricity

supply when the temperature reaches

450°C; the limiter restarts automatically.

We recommend using pans with a flat

bottom, switching the plate on after

positioning the pan and avoiding spilling

cold liquids on the hot plate.

Switching on the electric plates

Press the switch positioned before the appliance.

Turn dial “A” corresponding to the desired plate to align the

marker on the control panel with the position selected. The

green light “B” will light up.

Maximum power is position “6” and minimum power is

position “1”.

On start-up, turn the dial to “6”; once the maximum cooking value

is reached, turn the dial to a lower position.

0 1 2 3 4 5 6

Switching off the electric plates

Turn the dial to the off position “0”. Switch the power off using the switch positioned before the

appliance.

Switching on the static electric oven

The heating elements are controlled by a 4-position

selector. The internal chamber temperature is controlled

by a thermostat (60°C-300°C).

The dial is used to choose the most suitable heating mode,

activating the heating elements as required.

Turn the heating element control dial “C” to one of the

enabling positions. The green indicator light “E” lights up

to indicate that the machine is powered up.

Turn the thermostat dial “D” to the desired cooking

temperature marker. The orange indicator light “F” lights

up to indicate that the heating elements are in operation.

The oven door must be closed during

all cooking procedures.

OFF Lower and upper

heating elements

Upper heating

element

Lower heating

element

60°C 100°C 140°C 180°C 220°C 270°C

EN - 5

5410.256.08

Switching on the fan electric oven

Turn the thermostat dial “D” to the desired cooking temperature

marker. The green indicator light “E” lights up to indicate that the

machine is powered up and the fans are running. The orange

indicator light “F” lights up to indicate that the heating elements

are in operation.

0 60°C 100°C 140°C 180°C 220°C 270°C

Switching off the electric oven

Turn dials “C” and/or “D” to position “0”. Switch the power off using the switch positioned before the

appliance.

Safety thermostat

Electric ovens are fitted with a safety thermostat that cuts off the

electric power supply in the event of a fault or overheating.

To turn the appliance on again, remove the control panel, taking out the

screws located in the lower part, and press button “G”.

Contact a specialist technician.

EN - 6

5410.256.08

Part 3 – Maintenance and cleaning

Replacing parts

Faulty parts should only be replaced by qualified personnel. First, always disconnect the appliance from the gas and electric mains. After having

removed the control panel, all the functional parts of the appliance are easily accessible.

Only order spare parts from the manufacturer or an authorised dealer.

FAULTS

Malfunctions are not always due to the quality of the components used. These appliances are manufactured using top-quality components.

Malfunctions may be caused by voltage surges or by infiltrations of dust and/or dirt. In any case, if you suspect their is a fault, ALWAYS turn the

appliance off and call the authorised repair service.

Unauthorised persons should never attempt to repair the appliance or carry out

maintenance. Tampering with the appliance voids the warranty.

MAINTENANCE – TESTS – CHECKS – CLEANING FREQUENCY USER

SUPPORT

SERVICE

Cleaning

General cleaning of the appliance and the

surrounding areas

Daily or based on the

degree of use

Yes -

Safety devices

Check the safety devices function correctly Monthly Yes Yes

Mechanical protective

devices

Check condition. Check that there are no

deformations or loose/missing parts.

Monthly Yes Yes

Controls

Check the readability and condition of the

inscriptions and symbols. Repair if necessary.

Yearly

Yes Yes

Appliance structure

Check the mechanical part to make sure that

it is not broken or deformed. Check the screws

are tightened.

Yes Yes

Tighten the main bolts (screws, fasteners, etc.)

on the appliance

- Yes

Safety signs

Check the readability and condition of the

safety signs.

Yes Yes

Electrical control panel /

electronics

Check the condition of the electrical parts

installed on the electrical control panel.

- Yes

Check the wiring between the electrical panel

and the parts of the appliance.

Electrical connection

cable and plug socket

Check the condition of the connection cable

and plug socket.

Yes Yes

Replace if defective.

Yes

Motor bearings (if

present)

Replace motor bearings Every three years - Yes

EN - 7

5410.256.08

Cleaning and care

Only clean the appliance once it has

cooled.

Only use products that are food safe.

Use personal protective equipment (PPE)

when cleaning.

Do not wash the appliance with jets of

water. Any water entering the electric

components could lead to a malfunction.

Read the warnings provided on the detergent safety data sheets.

Keep the appliance clean to ensure it functions correctly and lasts

for a long time. Wash the removable parts separately with warm

water and detergent, then rinse them under running water. Clean

the steel parts with a damp cloth and a non-abrasive detergent,

then dry them using a soft, dry cloth. For stubborn deposits, use

hot water and vinegar. Do not use harsh or abrasive detergents to

clean the stainless steel parts. Do not use iron cleaning pads as they

may cause rust to form. For the same reason, avoid contact with

ferrous materials, heavy or coarse cloths, or steel wool.

When cleaning, avoid using abrasive paper or cloth. Only in special

cases, use pumice stone powder instead. For stubborn deposits,

we recommend using a sponge (e.g. Scotch-Brite). You can also

use oven and grill cleaning sprays, readily available on the market,

to remove stubborn deposits. If you use spray products, please

follow the manufacturer’s instructions. Do not use abrasive or acid

products on enamelled parts and do not clean using steel wool or

metal pads. Clean the oven after use. This will make it easier to

remove any residue, which would otherwise burn and cause bad

odours the next time you use the oven. To minimise emissions of

polluting substances into the environment, clean the appliance

with products that are at least 90% biodegradable.

Ecology and the environment

Our appliances are studied and optimised via testing to provide

high performance and yields. To reduce energy consumption

(electricity, gas and water), do not use the appliance for long

periods of time without food inside or in conditions that may

compromise optimum yield.

All of the following materials are used for the packaging:

•Polyethylene: external packaging film and/or bubble wrap

•Polypropylene: straps

•Expanded polystyrene: corner pieces, protective sheets and

blocks

•Cardboard

•Wooden base frame

These materials are environmentally friendly and can be safely

stored or reused/recycled. Should you wish to dispose of them,

please adhere to the waste regulations in force in your country.

Dispose of the appliance responsibly at the end of its

useful life.

In compliance with the regulations in force in your

country, dispose of the waste product by taking it to an authorised

collection and treatment site, after removing the power cable.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Tecnoinox Piano cottura

Tecnoinox

Tecnoinox PC70G7A Manuale utente

Tecnoinox

Tecnoinox PFRX12VE7 Manuale utente

Manuali Piano cottura popolari di altre marche

Bonnet

Bonnet OPTIMUM 700 Manuale del proprietario

Jenn-Air

Jenn-Air JGCP430 Manuale utente

Frigidaire

Frigidaire FES367FCC Guida rapida

Ztove

Ztove EZ2 DUO Manuale utente

Kleenmaid

Kleenmaid cooking GCTK9011 Guida all'installazione

Casselin

Casselin CSASRE24 Manuale utente

Jenn-Air

Jenn-Air JGC2536EB00 Manuale utente

Waldorf

Waldorf RN8603E-B Manuale di istruzioni

Whirlpool

Whirlpool SMP658CNEIXL Manuale utente

Wolf

Wolf CI243C/B Manuale utente

Fulgor Milano

Fulgor Milano F5PGK305S1 Manuale utente

GE JP389 Manuale utente

Wells

Wells WV-2HFG Manuale utente

IKEA

IKEA Lagan HGA4K Manuale utente

Samsung

Samsung NA36N9755 Manuale utente

Miele

Miele KM 404 Manuale utente

Lacor

Lacor 69562 Scheda tecnica

Keating Of Chicago

Keating Of Chicago MG-2 Manuale utente