TECshow Nebula 6 Manuale utente

USER MANUAL / MANUAL DE USUARIO / MANUAL DO USUáRIO

PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE /

POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR

LEIA AS INSTRUçõES CUIDADOSAmENTE ANTES DE USAR

English Version

Compare LED Par light with traditional par light, Led par light

have more rich color eects, color mixing eect rich, color

mixing eect of trichromatic LED of up to 16700000, the clas-

sication of LED par light: use is divided, One,It is a commer-

cial lighting, also called the spotlight, mainly plays the role of

illumination, high power LED Bulb,LED bulb usually use a sin-

gle color, small size, are oen used in shopping malls, hotels,

guesthouses, square fountain etc.. Two,Stage lighting, main-

ly to lighting, color change, making the stage atmosphere,

the size of the power LED has, LED Bulb color has red, green,

blue, white. Oen used for stage performances, wedding eti-

quette, exhibition and conference time.

NEBULA 6 - 12W * 6PCS LED PAR LIGHT

English Version

p. 2

p. 3

Safety instructions

WARNING!

• Please keep this User Guide for future consultation. If

you sell the unit to another user, be sure that they also

receive this instruction booklet.

• All xtures are intact from the manufacturer, please op-

erate follow up the user manual, articial fault are not

under guarantee repair.

• Unpack and check carefully that there is no transporta-

tion damage before using the unit.

• The unit is for indoor use only. Use only in a dry location.

• Do install and operate by operator.

• Use safety chain when xes the unit. Don’t handle the unit

by taking its head only, but always by taking its base.

• The unit must be installed in a location with adequate

ventilation, at least 50cm from adjacent surfaces.

• Be sure that no ventilation slots are blocked, otherwise

the unit will be overheated.

• Before operating, ensure that the voltage and frequency of

power supply match the power requirements of the unit.

• It’s important to ground the yellow/green conductor to

earth in order to avoid electric shock.

• Maximum ambient temperature TA : 40°C. Don’t operate

it where the temperature is higher than this.

• Don’t connect the device to any dimmer pack.

• First run, there will be smoke or smells, and all disap-

pearing a few minutes later.

• Make sure there are no ammable materials close to the

unit while operating, as it is re hazard.

• Look over power wires carefully, replace immediately if

there is any damage.

• Never run on for a long time lest shortening lifespan.

• Avoid any inammable liquids, water or metal objects

entering the unit.

• Once it happen, cut o the mains power immediately.

• Do not operate in dirty and dusty environment, also

cleaning xtures regularly.

• Do not allow children to operate the xture.

• Do not touch any wire during operation as there might

be a hazard of electric shock.

• Avoid power wires together around other cables.

• Disconnect mains power before fuse/lamp replacement

or servicing.

• Replace fuse only with the same type.

• In the event of serious operating problem, stop using the

unit immediately.

• Never turn on and o the unit time aer time.

• The housing, the lenses, or the ultraviolet lter must be

replaced if they are visibly damaged.

• Do not open the unit as there are no user serviceable

parts inside.

• Never try to repair the unit by yourself. Repairs carried

out by unskilled people can lead to damage or malfunc-

tion. Please contact the nearest authorized technical as-

sistance center.

• Disconnect the mains power if the xture is not used for

a long time.

• Do use original packing materials once transport it again.

• Do not look directly at the LED light beam while the x-

ture is on.

For power supply, do not connect in series much more

than 7 units, use another mains supply for next 7 units.

Please read the instructions carefully which includes important information about the installation, operation and maintenance.

NEBULA 6 - 12W * 6PCS LED PAR LIGHT

English Version

p. 4

Installation

The unit should be mounted via its screw holes on the brack-

et. Always ensure that the unit is rmly xed to avoid vibra-

tion and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is

able to support a weight of 10 times of the unit’s weight. Also

always use a safety cable that can hold 12 times of the weight

of the unit when installing the xture.

The equipment must be xed by professionals. And it must

be xed at a place where is out of the touch of people and has

no one pass by or under it.

Technical Specications

• Three operational modes: DMX, Master/Slave and

Sound Active

• DMX Channel mode: 6/9 CH

• Three built-in programs. Control Master/Slave mode

by voice

• 0-100% smooth dimming function

• Suitable for disco, bar mobile Dj, etc.

• Voltage: AC 100-240V, 50/60Hz

• Power consumption: 165W

• LEDs: 6 x 12W RGBWAUV

• Net weight: 2 Kg.

• Dimensions: 26x26x36 Cm.

How to Set the Fixture

1- The indicating light

2- Function display: display menu and the selected function

3- Menu button

4- Microphone

5- DMX signal output

6- Power supply socket

7- DMX signal input

NEBULA 6 - 12W * 6PCS LED PAR LIGHT

English Version

p. 5

DMX Mode

Channel slection mode

Master/Slave mode

Backlight mode

show positive and negative direction

manual mode

Auto-test

Machine using time

Performance mode

NEBULA 6 - 12W * 6PCS LED PAR LIGHT

English Version

p. 6

DMX Mode

Select the Addr menu, press the ENTER key to conrm. Then

use the initial address code DOWN/UP button to set this light

(A001 ~ A512). Once you have set your initial address code,

press ENTER to dene and save. Not to make any changes,

wait a minute to automatically exit the menu and save. The

main menu, please press the MENU button.

Channel selection mode

Select the Chnd menu, press the ENTER key to determine.

To use the DOWN/UP button to channel mode: 5Ch (5 Chan-

nel).9Ch (9 Channels) mode. Select the desired channel

mode, press ENTER to determine and save. Not to make any

changes, wait a minute to automatically exit the menu and

save. The main menu, please press the MENU button.

Master/Slave mode

Select the SLnd menu, press the ENTER key to conrm. To

use the DOWN/UP key set of Master-Slave mode need: NASt

(Master). SL 1 (Slave 1). SL 2 (Slave 2) mode. Select the de-

sired mode, press ENTER to determine and save. Not to make

any changes, wait a minute to automatically exit the menu

and save. The main menu, please press the MENU button.

Performance mode

Select the Shnd menu, press the ENTER key to determine.

To use the DOWN/UP button to Performance mode: SoUo

(Sound).CoLo (color).StCo (Strobe).Fade (Gradient) mode.

Select the desired mode, press ENTER to determine and

save. Not to make any changes, wait a minute to automati-

cally exit the menu and save. The main menu, please press

the MENU button CoLo (color) Co1 ~ Co12 12 program mode,

use the DOWN/UP button to select the desired mode, press

ENTER to determine and save. Not to make any changes,

wait a minute to automatically exit the menu and save. The

main menu, please press the MENU button StCo (STROBE)

have 0 ~ 255 to adjust the speed, use the DOWN/UP button

to select the desired speed, according to ENTER, determine

and save. Not to make any changes, wait a minute to auto-

matically exit the menu and save. The main menu, please

press the MENU button Fade (Gradient) SP1 ~ SP8 8 fade

speed selection, use the DOWN/UP button to select the gra-

dient speed required, according to ENTER, determine and

save. Not to make any changes, wait a minute to automati-

cally exit the menu and save. The main menu, please press

the MENU button.

Backlight mode

Select the LED menu, press the ENTER key to determine.

Then use the DOWN/UP button to set the backlight mode: ON

(Open).OFF (Close). Select the desired mode, press ENTER to

determine and save. Not to make any changes, wait a minute

to automatically exit the menu and save. The main menu,

please press the MENU button.

Show positive and negative direction

Select the dISP menu, press the ENTER key to determine. To

use the DOWN/UP button to display mode: dISP (positive).

DSIP (reverse). Select the desired mode, press ENTER to de-

termine and save. Not to make any changes, wait a minute

to automatically exit the menu and save. The main menu,

please press the MENU button.

Manual mode

Select the NAnu menu, press the ENTER key to determine. To

use the DOWN/UP button to display mode: Red (red), Gree

(green), Blue (blue) and Ublt (white). Select the desired mode,

press ENTER to determine and save. Not to make any changes,

wait a minute to automatically exit the menu and save. The

main menu please press the MENU button Red (red) with 0 to

255 using the DOWN/UP button to brightness press ENTER to

dene and save. Not to make any changes, wait a minute to

automatically exit the menu and save. The main menu please

press the MENU button Gree (green) with 0 to 255 using the

DOWN/UP button to brightness press ENTER to dene and

save. Not to make any changes, wait a minute to automat-

ically exit the menu and save. The main menu please press

the MENU button Blue (blue) with 0 to 255 using the DOWN/

UP button to brightness press ENTER to dene and save. Not

to make any changes, wait a minute to automatically exit the

menu and save. The main menu please press the MENU button

Ublt (white) with 0 to 255 using the DOWN/UP button to bright-

nessm press ENTER to dene and save. Not to make any chang-

es, wait a minute to automatically exit the menu and save. The

main menu please press the MENU button Ambe (amber) with

0 to 255 using the DOWN/UP button to brightnessm press EN-

TER to dene and save. Not to make any changes, wait a min-

ute to automatically exit the menu and save.

Auto-test

Select the Test menu, press the ENTER key to determine. The

machine will start automatically detect color. Not to make

any changes, wait a minute to automatically exit the menu

and save. The main menu, please press the MENU button

NEBULA 6 - 12W * 6PCS LED PAR LIGHT

English Version

Fhrs

Select the Fhrs menu, press the ENTER key to determine. You

can see the use of machine time / h. Not to make any chang-

es, wait a minute to automatically exit the menu and save.

The main menu, please press the MENU button

Temperature

Select the Tenp menu, press the ENTER key to determine. You

can see the machine light board temperature / degree. Not

to make any changes, wait a minute to automatically exit the

menu and save. The main menu, please press the MENU button

p. 7NEBULA 6 - 12W * 6PCS LED PAR LIGHT

English Version

DMX-512 Connections

The DMX-512 is widely used in intelligent lighting control with a

maximum of 512 channels.

Temperature reduces signal error and avoids signal transmis-

sion problems and interference. It is always advisable to con-

nect a DMX terminal.

(Resistance 120 ohm 1/4W) between pin2 (DMX-) and pin3

(DMX+) of the last xture

6CH Channel mode

p. 8NEBULA 6 - 12W * 6PCS LED PAR LIGHT

English Version

9CH Channel mode

p. 9

Fixture Cleaning

The cleaning of internal must be carried out periodically to

optimize light output. Cleaning frequency depends on the

environment in which the xture operates: damp, smoky or

particularly dirty surrounding can cause greater accumula-

tion of dirt on the xture’s optics.

• Clean with so cloth using normal glass cleaning uid.

• Always dry the parts carefully.

• Clean the external optics at least every 20 days. Clean

the internal optics at least every 30/60 days

NEBULA 6 - 12W * 6PCS LED PAR LIGHT

English Version

NEBULA 6 - 12W * 6PCS LED PAR LIGHT

Versión Español

p. 10

Versión Español

En comparación con el producto PAR tradicional, este nuevo

equipo PAR LED ofrece efectos con colores más ricos, lo que

permite mezclas de colores de LED tricromáticos de hasta

16 700 000 variantes. El producto PAR LED puede tener dife-

rentes usos. Por un lado, en aplicaciones comerciales (como

spotlight), donde podrá utilizarlo principalmente para fun-

ciones de iluminación con una bombilla LED de alta poten-

cia. La pequeña bombilla LED, de un único color, se utiliza,

por lo general, en establecimientos comerciales, hoteles y

fuentes de agua, entre otras aplicaciones. Por otro lado, este

equipo se utiliza para aplicaciones de iluminación en esce-

narios, principalmente dado que aprovecha las funciones de

cambio de colores, lo que genera una puesta en escena ini-

gualable, gracias al poder de la iluminación LED. La bombilla

LED cuenta con cuatro colores: rojo, verde, azul y blanco. Se

utiliza, por lo general, en representaciones teatrales, bodas,

exhibiciones y conferencias.

Indice

Lingue:

Altri manuali TECshow Proiettore

TECshow

TECshow Octobeam RGBW Manuale utente

Manuali Proiettore popolari di altre marche

VIZULO

VIZULO Micro Martin Guida utente

EuroLite

EuroLite LED IP FL-100 SMD Manuale utente

Cooper Wheelock

Cooper Wheelock XB12 Manuale utente

Allen + Roth

Allen + Roth 17624-000 Manuale utente

ADJ

ADJ 4 STAGE PAK Manuale utente

Cooper Lighting

Cooper Lighting EGL91SW233 Manuale utente

Max

Max 37496 Manuale utente

BEGA

BEGA 85 143 Manuale utente

Beamz

Beamz 151.226 Manuale utente

EuroLite

EuroLite LED IP FL-8 Manuale utente

Ledj

Ledj PERFORMER 36 RGB Manuale utente

Perel

Perel ELS3 Manuale utente

Perel

Perel ELS3WD Manuale utente

LumX

LumX LM 36130 Manuale utente

Xtricity

Xtricity 4-80053 Manuale utente

Stahl

Stahl 6521/4 Series Manuale utente

Ecosense

Ecosense EcoSpec Manuale utente

Ayrton

Ayrton minipanel FX Manuale utente