Tekkeon MP3450 Manuale utente
MP3450/MP3450-10 User Guide
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 1
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 2
USER GUIDE
Contents
Overview ......................................................................................................2
Getting Started..............................................................................................2
Unpacking myPower ALL Plus..................................................................2
Getting to Know myPower ALL Plus ........................................................3
Charging myPower ALL Plus ....................................................................3
Using myPower ALL Plus ............................................................................4
Select/Connect the Adapter Plug ..............................................................5
Connect the Power Output Cord ..............................................................6
Adjust the Voltage Level............................................................................6
Connect the Portable Device ....................................................................8
Connect the 5V Device ..............................................................................8
View myPower ALL Plus Battery Capacity ................................................9
Recording Device Information ................................................................10
Obtaining Adapters..................................................................................10
Using the Extended Battery (MP3450-10) ..................................................10
Adding the Extended Battery ..................................................................10
Charging the Extended Battery................................................................11
Troubleshooting ..........................................................................................11
Limited Warranty ........................................................................................12
Customer Support ......................................................................................13
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 1
2
Overview
You can use myPower™ ALL—the universal rechargeable battery—to power just about any portable
device. Simply connect myPower ALL to your notebook computer, portable DVD player, digital
camera, digital camcorder, portable CD player, PDA, mobile phone, or other portable device to
extend the battery life. As an added bonus, myPower ALL will charge the internal battery on some
devices, while also powering the device.
myPower ALL MP3450 can be used alone, or with the optional extended battery (MP3450-10) to
double the capacity. The extended battery with mounting brackets is sold separately.
Getting Started
Unpacking myPower ALL Plus
Your myPower ALL Plus package includes the following:
User guide (not shown)
Adapter plug kit with drawstring bag
(8 adapter tips)
Power output cord
Power adapter Device At-A-Glance
Card
myPower ALL Plus
lithium polymer
rechargeable battery
Retractable
USB cable
Mini USB tip
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 2
3
USER GUIDE
Getting to Know myPower ALL Plus
Charging myPower ALL Plus
myPower ALL Plus will charge in four hours when completely empty. The green CHARGE indicator will
turn on after the battery is 80% charged. Therefore, you should view the actual battery capacity before
disconnecting the power adapter to stop charging. (Before using myPower ALL Plus for the first time,
you must charge the device for four hours.)
1. Remove the output cord from the DC OUT jack, if connected.
2. Plug the power adapter into the DC IN jack on the end of myPower ALL Plus.
3. Plug the power adapter into a wall outlet.
The red CHARGE indicator will turn on to indicate the
battery is charging and is less than 80% charged.
4. When the green CHARGE indicator turns on, set the voltage lock to LOCK, and press the voltage
selector to view the battery capacity. If the capacity does not indicate full (green LEDs on), continue to
charge the battery until the battery capacity indicates full.
Voltage Indicators/Capacity Indicators
Voltage
Lock/USB
Power
DC OUT
For connection
to device
DC IN
For connection
to power adapter
Voltage Selector USB Port for connection
to 5V device
Battery port for connection
to MP3450-10
Charging/USB Indicator
MP3450 MP3450-10
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 3
4
5. When the battery capacity indicates full, unplug the power adapter and slide the voltage lock right to the
unlocked/off position (UNLOCK/OFF) to turn off the USB power when myPower ALL Plus is not in use.
NOTE: myPower ALL Plus will automatically shut down the power input when fully charged, so you can
charge it overnight.
Using myPower ALL Plus
myPower ALL Plus can be used to power and/or charge up to two portable devices simultaneously.
With devices that require higher voltage levels, like notebook computers and portable DVD players,
we recommend that you use myPower ALL Plus only to power the device. You will find that powering
without charging your higher voltage device will maximize the battery life of myPower ALL Plus, thus
letting you use your portable device even longer.
To use myPower ALL Plus to power and/or charge your device, take these steps which are described in
detail in the following sections.
• Select an adapter plug for your main device and connect the plug to the output cord.
• Connect the power output cord to myPower ALL Plus.
• Adjust the voltage level to match that of your main device and lock the voltage setting.
• Connect the adapter plug/output cord to your main device.
• Connect a second 5V device.
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 4
5
USER GUIDE
Select/Connect the Adapter Plug
1. Select the adapter plug that fits securely into the power jack on your
portable device.
2. Locate the polarity symbol on your device in the area around the
power connector jack:
WARNING: myPower ALL Plus supports Center Positive polarity only. If your device has a Center
for assistance.
3. Connect the adapter plug to the power output cord (but not the device).
If you are using a UA-xxx adapter (rather than
PA-xxx), you must insert the L34 adapter that
came with your myPower ALL Plus between the
adapter cord and UA-xxx adapter as shown.
CAUTION: If you change the adapter plug while the
power adapter cord is connected to myPower ALL
Plus, the voltage setting will reset to the lowest
voltage, which is the default voltage setting.
Center Negative
Center Positive
L34 Adapter for
myPower ALL Plus
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 5
6
Connect the Power Output Cord
1. Plug the large end of the power output cord into the DC OUT jack on the end of myPower ALL Plus.
The 5V voltage indicator will turn on to indicate that the voltage is set to the lowest setting.
(If you have previously selected a voltage, the voltage selection will be returned to the lowest setting.)
Adjust the Voltage Level
1. Locate the voltage specification for your portable device. This can be found
on the device power adapter label or device specification label which
typically is found on the bottom of the unit.
(If available, use the voltage specification shown on the power adapter.)
2. With the voltage lock in the unlocked position (switched right to UNLOCK),
set the voltage output to the voltage selection that is equal to or one
increment higher than the voltage identified for your device. To do this,
press the voltage selector until the voltage indicator turns on under the
appropriate voltage selection (5, 6, 7.5, 9, 12, 14, 16, 19). For example, if
your device requires 6V, set the voltage to 6. If your device requires 7.2V,
set the voltage to 7.5.
CAUTION: It is important to set the voltage selector NO MORE than one step higher than the voltage
requirement for the portable device as an incorrect setting may prevent myPower ALL Plus from working
with your device, or may harm your device in the rare instance that the device accepts the higher voltage.
However, for all devices, adjusting the voltage ONLY one step higher than required will not harm the
device.
3. Slide the voltage lock to the locked position (switched left to LOCK). This will prevent you from
accidentally selecting a different voltage while your device is connected.
4. To change the voltage, slide the voltage lock to the unlocked position (UNLOCK), and select a new
voltage. Be sure to relock the voltage.
Sample Power Adapter Label
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 6
7
USER GUIDE
TIP: You can optimize the use of myPower ALL Plus with your notebook computer or portable DVD
player by setting the voltage on myPower ALL Plus to less than the required voltage shown on the
notebook computer power supply. This prevents myPower ALL Plus from charging the device, thus
extending the amount of time you can use myPower ALL Plus to power your notebook computer.
Most notebook computers have a battery voltage of 11.1V or 14.8V, allowing them to be powered with
12V or 14V. Therefore, it is recommended that you set the voltage to 12V first, and then test to see if it
will power your notebook. If not, increase the voltage to 14V, and retest. For MP3400 repeat this process
until you reach the voltage that will power your notebook.
Most portable DVD players require 9 or 12 volts. Set the voltage to 7.5V and test to see if myPower ALL
Plus will power your device at this setting. If not, increase the voltage by one level and retest.
Device Type Voltage on Device Suggested Voltage on
Power Adapter myPower ALL Plus
Notebook Computers
14V 12V
16V 14V
19V 14 - 16V
24V 19V
Portable DVD Players 9V 7.5 - 9V
12V 9 - 12V
Digital Cameras 5 - 6V 5 - 6V
CD Players 4.5 - 5V 5V
PDAs 5V 5V
Mobile Phones 3.7 - 6V 5 - 6V
Digital Camcorders 9V 7.5 - 9V
12V 9 - 12V
MP3/MP4 5V 5V
myPower ALL Plus VOLTAGE SELECTION
This table
provides
recommended
voltage
settings by
device type.
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 7
8
Connect the Portable Device
1. Connect the adapter plug into the power jack on the portable device.
2. Turn on the portable device and use it as you would normally.
While connected, myPower ALL Plus
will power and charge your device. (As mentioned earlier, myPower ALL Plus will not charge a device
if the voltage setting is lower than that required.)
or
Leave the portable device turned off and myPower ALL Plus will charge the device battery.
3. When finished, unplug the power output cord from myPower ALL Plus and your device and slide the
voltage right to the unlocked/off position (UNLOCK/OFF) to turn off the USB power when myPower
ALL Plus is not in use.
NOTE: If your portable device displays a low voltage/low capacity or double-beep warning while
myPower ALL Plus is connected, adjust the voltage setting to one level higher
.
TIP: For most portable devices, myPower ALL Plus can be used to power the device even when the
device battery is not installed.
Connect the 5V Device
1. Connect the USB adapter tip (or other optional adapter tip UA-xxx) into the retractable USB cable.
2. Connect the retractable USB cable into the USB port on myPower ALL Plus.
3. Connect the adapter tip into your 5V device.
4. Slide the voltage lock to the lock/on position (LOCK/ON) to turn on the USB port.
While connected,
myPower ALL Plus will power and charge your device.
5. Slide the voltage lock to the unlocked/off position (UNLOCK/OFF) to turn off the USB power when
myPower ALL Plus is not in use.
NOTE: The USB port provides only 5V of power, so the voltage cannot be changed. When using this port,
you will not select the voltage.
MP3450_ug_0507_rev3_r1 6/6/07 10:08 AM Page 8
Altri manuali per MP3450
5
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Tekkeon Accessori per laptop
