Teknion transit Manuale utente
Flush End (TLFE), Flush End Bracket (TLMK3F) Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 01
FLUSH END AND FLUSH END BRACKET
WORKSURFACES & COUNTERTOPS
May 2018 4 of 4
TST_251
transit
Installation Guides
E2
E1
C
A
D
A1 - Flush End
(TLFE) x1
C - Flush End Bracket
(A15-9257) x1
B1 - 1/4" - 20 x 5/8" Machine
Screw Quad. Pan Washer
(E01-0098) x4
B2 - #10 x 0.875" LG. Screw,
Quad. Pan Washer
(E01-0077) x4
D - Worksurface
(TWRR) x1
A2 - 1/4" - 20 x 5/8" Mach Scr,
Black, Quad, Truss
(E01-0113) x6
E1 - FS Main Modesy Panel
Sub-Assembly
(N30-0011\X) x1
E2 - FS Wire Tray Modesty Panel
(N30-0008\X) x1
F1 - Reinforcement
Channel
(A15-6956) x1
C - Flush End Bracket
(TLMK3F) x1
E - FS Modesty Panel (TLMO) x1
E3 - 1/4" - 20 x 5/8" Mach Scr,
Black, Quad, Truss
(E01-0113) x4
F - Worksurface Reinforcement Channel (Only required
for Worksurfaces 48" and up)
(UNRC) x1
F2 - #10 x 0.875"
LG. Screw,
Quad. Pan
Washer
(E01-0077)
xqty. varies
STEP 2: For Worksurfaces 66" or wider follow the isntallation step for the Support on Step 1,
then install a Reinforcing Channel as shown above.
NOTE: Channel location (L) = 1.75"
STEP 1: Flip the Worksurface onto a clean surface. Flip the Flush End Support upside down
and align the holes on the support with the holes on the Worksurface. Secure the support with
Screws provide in the kit.
Section:
Description: Page No:
Date:
INSTALL SUPPORT INSTALL SUPPORT (FOR WORKSURFACE ≥ 60")
TST_251
4 of 4
May 2018
FLUSH END AND FLUSH END BRACKET
WORKSURFACES & COUNTERTOPS
transit
Installation Guides
A1
B1
B1
A1
D
F2
F1
STEP 4: Install the Flush End Bracket and secure it with the Screws removed on Step 3.STEP 3: Remove Screws located at the back on the Flush End Support as shown above.
Section:
Description: Page No:
Date:
PREPARATION FOR FLUSH END BRACKET INSTALL FLUSH END BRACKET
TST_251
4 of 4
May 2018
FLUSH END AND FLUSH END BRACKET
WORKSURFACES & COUNTERTOPS
transit
Installation Guides
A2
A1
C
A2
STEP 5: Align the whole on the Modesty Panel with the holes on the Flush End Bracket.
Secure the Modesty Panel with Screws provided.
STEP 6: Align the holes on the Wire Tray with the holes on the Modesty Panel. Secure it with
Screws provided.
NOTE: FS Wire Tray Modesty Panel is adjusted to position the vinyl trim flush to the
underside of the Worksurface.
STEP 7: Using a leveler, adjust the Gable Leveler to level the assembled Worksurface.
Section:
Description: Page No:
Date:
INSTALL MODESTY PANEL INSTALL WIRE TRAY
LEVEL THE ASSEMBLED WORKSURFACE
TST_251
4 of 4
May 2018
FLUSH END AND FLUSH END BRACKET
WORKSURFACES & COUNTERTOPS
transit
Installation Guides
C
E3 E1
E2
E3
Altri manuali Teknion Rack e supporto
Teknion
Teknion Interpret Istruzioni operative e di manutenzione
Teknion
Teknion YMSTR Manuale utente
Teknion
Teknion JNSASW Manuale utente
Teknion
Teknion interpret WWSTW Manuale utente
Teknion
Teknion YMSTA Istruzioni operative e di manutenzione
Teknion
Teknion THSCD Manuale utente
Teknion
Teknion HNBEBF Istruzioni operative e di manutenzione
Teknion
Teknion Interpret Istruzioni operative e di manutenzione
Teknion
Teknion district SUPPORT FOOT FOR DISTRICT FREESTANDING WITH GLASS PANEL... Manuale utente
Teknion
Teknion complements CEREBRO Istruzioni operative e di manutenzione
