Tektronix TDS6UP Manuale utente
Instructions
TDS6UP, TDS7UP, and CSA7UP Option CPU
Upgrade Kit
071-1244-00
*P071124400*
071124400
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com
Copyright ©Tektronix, Inc. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Tektronix, Inc., P.O. Box 500, Beaverton, OR 97077
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit 1
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary in the product service manual
or the instruction manual.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
Service Safety Summary
2TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit 3
Kit Description
This document supports upgrading the NLX CPU board and microprocessor. To
upgrade your NLX CPU board and microprocessor perform each of the
following procedures in order.
Products
TDS6000 Series All serial numbers
TDS7000 Series All serial numbers
CSA7000 Series All serial numbers
Minimum Tool and Equipment List
Table 1: Equipment list
Required tools and equipment Part number
Screwdriver handle 620-440
T-20 Torx tip 640-250
T-15 Torx tip 640-247
1/8inch flat-bladed screwdriver Standard tool
#0 Phillips screwdriver Standard tool
3/16 inch open-end wrench Standard tool
Kit Description
4TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
Kit Parts List
Circuit/figure
number Quantity Part number Description
11ea 650--4562--00 COMPONENT KIT;MOTHERBOARD/
MICROPROCESSOR UPGRADE;TDS6/7UP
OPTION CPU
21ea 407--4880--01 BRACKET; CD--ROM, REAR DRIVE BAY
CHASSIS, 0.035 CRS
1ea 020--2349--XX SOFTWARE KIT; LICENSE CERTIFICATE,O/S
EASY RESTORE,CERTIFICATE AUTHENTIC-
ITY,WIN98 RESTORE CD
1
2
Figure 1: CPU upgrade kit parts
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit 5
Installation Instructions
This section contains all procedures needed to install TDS6UP, TDS7UP, or
CSA7UP Option CPU in the TDS6000, TDS7000, and CSA7000 Series
instruments.
These instructions are for personnel who are familiar with servicing the product.
If you need further details for disassembling or reassembling the product, refer to
the appropriate product manual. Contact your nearest Tektronix Service Center
or Tektronix Factory Service for installation assistance.
CAUTION. To prevent static discharge damage, service the product only in a
static-free environment. Observe standard handling precautions for static-sensi-
tive devices while installing this kit. Always wear a grounded wrist strap,
grounded foot strap, and static resistant apparel while installing this kit.
Remove
This section contains procedures for removal and installation of all mechanical
and electrical modules.
HLine Cord
HTrim (all)
HBottom cover
HLeft and Right covers
HNLX board
HRear chassis
HCD drive bracket
Preparation
WARNING. Before doing this or any other procedure in this manual, read the
Safety Summary found at the beginning of this manual.
Installation Instructions
6TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
This subsection contains the following items:
HThis preparatory information that you need to properly do the procedures
that follow.
HList of tools required to remove and disassemble all modules.
HProcedures for removal and reinstallation of the electrical and mechanical
modules.
WARNING. Before doing any procedure in this subsection, disconnect the power
cord from the line voltage source. Failure to do so could cause serious injury or
death.
NOTE. Read Equipment list for a list of the tools needed to remove and install
modules in this instrument. See Table 1, on page 3.
Equipment Required. Most modules in the TDS6000, TDS7000, and CSA7000
Series Instruments can be removed with a screwdriver handle mounted with a
size T-15, Torx screwdriver tip. Use this tool whenever a procedure step instructs
you to remove or install a screw unless a different size screwdriver is specified in
that step. All equipment required to remove and reinstall each module is listed in
the first step of the procedure.
Procedures for External Modules
The following procedures are found here and are listed in the order presented.
HLine Cord
HTrim (all)
HBottom cover
HLeft and Right covers
Installation Instructions
TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit 7
1. Assemble equipment and locate modules to be removed: Locate the power
switch and AC power cord connector in Figure 2 on page 7.
2. The instrument has a built-in soft power-off function that safely powers off
the instrument when you press the On/Standby switch.
3. Power off the rear panel power switch before servicing the power cord.
4. Orient the instrument: Set the instrument so that the bottom is down on the
work surface and the rear is facing you.
5. Remove line cord: Find the line cord on the rear cover. Pull the line cord
away to remove from the AC power connector.
6. Reinstallation: Do in reverse step 5 to reinstall the line cord.
AC power
cord
Line fuse
holder
Line fuses
AC power cord
connector
Power
switch
Figure 2: Line cord removal
Line Cord
Installation Instructions
8TDS6UP, TDS7UP, and CSA7UP Option CPU Upgrade Kit
1. Locate module to be removed: Locate the Trim in the locator diagram. See
Figure3,onpage9.
2. Remove the front panel trim: Use Figure 3 on page 9 as a guide.
a. To prevent the power button from falling out of the front panel trim,
place a piece of tape over the button.
b. Grasp the trim ring by the top edge and pull toward you to detach the
three plastic snaps. (Alternatively, you can use a flat-bladed screwdriver
or other small prying tool to help you detach the snaps.)
c. Swing the bottom of the ring upward and off the front panel.
3. Remove the acquisition trim: Use Figure 3 on page 9 as a guide.
a. Remove the three T-15 Torx screws that secure the acquisition trim to
the instrument.
b. Remove the acquisition trim from the instrument.
4. Remove the top cover trim: Use Figure 3 on page 9 as a guide.
a. Remove the accessory pouch; it snaps off.
b. Remove the four T-15 Torx screws that secure the top cover trim to the
instrument. The T-15 Torx screws also secure the snap studs to the top
cover.
c. Remove the top cover trim from the instrument.
5. Remove the carrying handle and the right/left side trim panels: Use Figure 3
on page 9 as a guide.
a. Remove the T-20 Torx screws that secure the handle to the instrument.
Remove the handle from the instrument.
b. Slide the side trim panels towards the rear of the instrument allowing the
tabs to clear the cover openings, and then pull out to remove the panels
from the instrument.
6. Reinstallation: Do in reverse steps 2 through 5 to reinstall the appropriate
trim.
Trim and Carrying Handle
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Tektronix Hardware per computer
Tektronix
Tektronix Colorado Data Systems 53A-334 Manuale utente
Tektronix
Tektronix TMS 101 Manuale utente
Tektronix
Tektronix WVR6020 Manuale di istruzioni
Tektronix
Tektronix Socket 7 TMS109A Manuale utente
Tektronix
Tektronix TMS 440 SH-3 7708 Manuale utente
Tektronix
Tektronix XD88F14 Manuale utente
Tektronix
Tektronix IPB220 Manuale operativo
Tektronix
Tektronix TMSST1 Manuale utente
Tektronix
Tektronix 067-0832-01 Manuale utente
Tektronix
Tektronix BERTScope Manuale
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
