Teldat T200 Manuale utente

Teldat T200 Router Family

Teldat-Dm 418-I

Teldat S.A. Manual

Teldat T200 Router Family 1

Legal Notice

Warranty

This publication is subject to change.

Teldat S.A. offers no warranty whatsoever for information contained in this manual.

Teldat S.A. is not liable for any direct, indirect, collateral, consequential or any other damage connected to the deliv-

ery, supply or use of this manual.

Manual Teldat S.A.

2Teldat T200 Router Family

Table of Contents

I ImportantInformation................................ 1

Chapter1 Installation...................................... 2

1.1 Introduction...................................... 2

1.1.1 Recycling and the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.2 Connections...................................... 3

1.2.1 PowerSourceConnection................................ 3

1.2.2 DataConnections.................................... 4

1.3 MeaningoftheLEDs.................................. 6

1.4 Programming the microswitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.4.1 Procedure to ignore the configuration, or establish the default configuration . . . . . . . . . . 7

Chapter2 Appendix...................................... 9

2.1 TroubleShooting.................................... 9

2.2 SoftwareUpgrading................................... 9

2.3 Connectors ...................................... 9

2.3.1 LAN Connector (FE 0 and Switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.3.2 SERIALConnector.................................. 10

2.3.3 ConfigurationConnector................................ 11

2.4 TechnicalSpecifications................................ 11

2.5 Translated safety warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Teldat S.A. Table of Contents

Teldat T200 Router Family i

Table of Contents Teldat S.A.

ii Teldat T200 Router Family

I Important Information

Note

The manufacturer reserves the right to make changes and improvements in the appropriate features in

either software or hardware of this product, modifying the specifications of this manual without prior no-

tice.

The images showing the front and back panels of the device are for information purposes only. Some

small modification may exist in the actual device.

The equipment is intended to be installed by Service Personnel and only handled by qualified person-

nel. If not, the device may be damaged and malfunction.

This device contains elements that are sensitive to electrostatic surges and shocks. Therefore, it is es-

sential when handling the equipment that an antistatic wriststrap is connected to the device chassis and

that this is placed on an antistatic mat. Furthermore, it is crucial to avoid any kind of contact between

the device components and necklaces, bracelets, rings, ties etc.

Teldat S.A. Important Information

Teldat T200 Router Family 1

Chapter 1 Installation

1.1 Introduction

The Teldat T200 is a general-purpose IP router, suitable for a wide range of applications (personal, SOHO/SME and

corporate environments). It adapts perfectly to plenty of IP scenarios, providing simultaneous access to Internet for

private LAN users and accommodating teleprocess networks and SNA support.

The Teldat T200 router has a 4 or 8 port Ethernet LAN Switch and a Fast Ethernet port that behaves as WAN. You

can configure a serial port in the 4-port model, which can be used in X.25, SDLC, Frame Relay scenarios or with an

external backup device.

This manual shows you how to install and connect the router.

Fig. 1: Teldat T200G: External aspect

Fig. 2: Teldat T200: External aspect

1.1.1 Recycling and the Environment

Please do not, under any circumstances, throw away any Teldat T200 routers with normal domestic waste. Ask your

local town hall for information on how to correctly dispose of them in order to protect the environment against e-

waste. Always respect the current laws regarding waste material. Anyone found violating the environmental laws will

be subject to fines and any additional steps established by law.

All the packing materials i.e. the cardboard box, plastic and any other packaging, together with the pieces making up

aTeldat T200 , must be recycled complying with the current active laws regarding recycling materials.

The symbol shown below with a cross over the rubbish container can be seen on the device. This means that, when

a device reaches the end of its life, it must be taken to the official recycling/disposal centers where it must be dis-

posed of in an environmentally responsible manner and separately from normal domestic waste.

1 Installation Teldat S.A.

2Teldat T200 Router Family

1.2 Connections

Note

BEFORE INSTALLING THE ROUTER, PLEASE READ THE FOLLOWING INSTRUCTIONS CARE-

FULLY

Workplace Conditions. Main Characteristics

• Excessive cold and heat should be avoided, as should humidity and dust.

• Avoid direct exposure to sunlight and any other heat sources. Do not place the device between papers, magazines

or other items that could hinder natural air circulation.

• Do not place the device near strong electromagnetic fields such as those produced by speakers, motors, etc.

• Avoid knocks and/or strong vibrations during operation, storage and transport.

Warning

The electric current in power cables, telephone lines and communication cables is dangerous. To pre-

vent electric shocks, before installing, handling or opening the equipment covers, connect and discon-

nect the cables following the steps set forth in the following section.

To Connect To Disconnect

Make sure the device’s power supply is OFF. Switch off the device.

Connect all data cables. Disconnect the power supply.

Connect the power supply to the device. Disconnect the data cables.

Turn the switch ON.

1.2.1 Power Source Connection

The Teldat T200 does not require any special conditions regarding voltage stability or protection against power loss,

as it is already protected.

To avoid electric shocks, residual current circulation and any other unwanted effects that may disrupt communica-

tion, the following is recommended:

Warning

All interconnected communication devices should be plugged to THE SAME GROUNDED POWER

OUTLET, which should, at the same time, be of good quality (lower than 10 ohms).

Whether the workplace is provided with an uninterrupted power supply system (UPS), regulated supply,

or it is independent from the rest (such as lighting, etc.), it is highly recommended that all data devices

should be connected to the same power source. This will avoid operating and premature aging prob-

lems of drivers and other components.

To connect the power source to the device: ensure the switch is OFF (0) and the power supply is NOT connected to

the main electricity supply; find the POWER plug (located on the rear panel of the device) and plug it into the power

source. Both the connector and the receptacle are designed to ensure their proper installation.

Teldat S.A. 1 Installation

Teldat T200 Router Family 3

Fig. 3: T200G Power connection and switch

Fig. 4: T200 Power connection and switch

1.2.2 Data Connections

The Teldat T200 is equipped with the following connectors (although some of these may not be available depending

on the model):

SWITCH:

The Teldat T200 incorporates a 4 or 8 port Switch 10/100BaseT with automatic MDI/MDIX for LAN (local area net-

work) connection. It also has a LED indicating connectivity.

Please pay close attention to the labelling to avoid confusing the switch with other port types.

Fig. 5: T200G 8 port Switch (LAN)

Fig. 6: T200 4 port Switch (LAN)

FE 0:

The Teldat T200 has one female RJ45 connector in order to connect to the Ethernet 10BaseT / 100BaseT networks

through shielded twisted pairs (STP) or unshielded (UTP) cables.

Depending on the design of the network, the connection is carried out through a HUB or directly to another terminal

device Ethernet interface through a crossover cable (please consult your supplier for information on crossover Ether-

net cables).

Fig. 7: T200G Fast Ethernet Port (FE 0)

1 Installation Teldat S.A.

4Teldat T200 Router Family

Fig. 8: T200 Fast Ethernet Port (FE 0)

SERIAL:

Multistandard serial interface to connect an external modem, POS, or to connect to a WAN (wide area network) such

as X.25, Frame Relay, PPP, etc.

It requires an insertable driver (V.24, V.35, V.36, X.21, RS-485) to operate.

Fig. 9: SERIAL connector

1.2.2.1 Connecting for configuration

The Teldat T200 has a RJ45 female connector on the rear panel labeled CONF. ,which provides access to the

router’s local console. For configuration purposes, connect the CONF. port to an asynchronous terminal (or

to a PC with terminal emulation).

Fig. 10: T200G Configuration connector (CONF.)

Fig. 11: T200 Configuration connector (CONF.)

The terminal configuration is as follows:

- Speed: 9600 bps

- Eight data bits

- One stop bit

- No parity bit

- No type of flow control

To connect to the configuration port, use the RJ45 connector cable and the RJ45 female-DB9 female adaptor, both

provided with the router. In cases where the terminal has DB25 connections, you must use an additional adapter.

Teldat S.A. 1 Installation

Teldat T200 Router Family 5

Fig. 12: Connecting for configuration

1.3 Meaning of the LEDs

Fig. 13: Teldat T200 : Front panel

Fig. 14: Teldat T200 : Front panel

ON Power-on indicator. It lights up when connected to the power.

SRouter operation:

OFF: System off.

GREEN: System initialized and operating.

YELLOW: System with Telnet session established.

FE 0 Fast Ethernet - WAN:

OFF: Interface not supported or not available.

RED: Interface is not available either because it is not enabled or there is a mal-

function in the auto-test.

YELLOW: Interface initialization in process.

GREEN: Interface available. Blinking: Maintenance frame being sent.

(T200G)

Switch(es) LAN Ethernet:

OFF: Switch(es) not available.

RED: Active Switch(es), there are no active devices connected.

GREEN: Active Switch(es), there is at least one active device connected.

Blinking: “heartbeat”.

LAN Switch(es) LAN Ethernet:

1 Installation Teldat S.A.

6Teldat T200 Router Family

Indice

Altri manuali Teldat Router di rete

Teldat

Teldat ATLAS 160 Manuale utente

Teldat

Teldat ATLAS 300 Manuale utente

Teldat

Teldat Teldat-3Ge-USB Manuale utente

Teldat

Teldat Router Manuale utente

Teldat

Teldat RXL14000 Manuale utente

Teldat

Teldat C+ Series Manuale utente

Teldat

Teldat C1+L Manuale utente

Teldat

Teldat iM8 Manuale utente

Teldat

Teldat 4Ge Manuale utente

Teldat

Teldat H1 RAIL Series Manuale utente

Teldat

Teldat TLDPV00A1 Manuale utente

Teldat

Teldat C Manuale utente

Teldat

Teldat H2 RAIL Manuale utente

Teldat

Teldat iM8-Cx Manuale utente

Teldat

Teldat SDE Manuale utente

Teldat

Teldat H2 RAIL Manuale utente

Teldat

Teldat Edge Router Atlas-840 Manuale utente

Teldat

Teldat Connect 104KF TLDPM00A1 Manuale utente

Teldat

Teldat 5Ge-Rail Manuale utente

Teldat

Teldat H2 RAIL Lite Manuale utente

Teldat

Teldat M1 Manuale utente

Teldat

Teldat Regesta Smart PLC Manuale utente

Teldat

Teldat Connect-4GePlus Manuale utente

Teldat

Teldat H1 HSDPA Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza