TeleAdapt PowerHub E Manuale utente
1
PowerHub E TA-7531US
INSTALLATION GUIDE
2
PowerHub E Installation Guide
1
PowerHub E Installation Guide
Table of Contents
2 Products Covered By This Installation Guide
2 PowerHub E Part Numbers
3 Important Safety Instructions
3 Approval Information
4 What Is Included In The Box
5 Preparation For Installation
6 Installation
7 Additional Information
8 Warranty
9 Contact Details
Products Covered By This Installation Guide
The TeleAdapt PowerHub E (TA-7531US) is a furniture power
distribution unit which provides two tamper-resistant US NEMA
receptacles and 2 USB-A charging sockets.
The use of a tamper-resistant receptacles gives industry leading
protection against the accidental insertion of foreign objects into the
power sockets and provides enhanced safety for all users.
The TA-7531US is provided with 2 trims (Slimline black and Slimline
metallic) and a duplex power plug so the number of available
outlets in a room is not reduced when it is tted.
Installation is simple as the TA-7531US only requires a single
connection to a US 120V/60Hz outlet, so tting can be undertaken
by anybody who has a screwdriver and does not require a qualied
electrician.
PowerHub E Part Numbers
TA-7531US-USN2 PowerHub E for USA, 2 metre power cable.
2Important Safety Instructions
• Read these instructions carefully before attempting any
installation. Follow all instructions and heed all warnings.
These instructions should be kept for future reference.
• This equipment must be securely attached to furniture in strict
accordance with these installation instructions.
• This equipment is designed for indoor use only.
• Only use with attachments and accessories as specied by
the manufacturer.
• The mains plug used to disconnect this equipment from its
power source must be readily accessible at all times.
• Ensure the power cord is uncoiled before installation.
• Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles and the point
where they exit from the equipment.
• The power cord must be plugged into a mains socket outlet
with protective earthing.
• Clean only with a dry cloth.
• Refer all servicing to qualied service personnel. Servicing is
required when the equipment has been damaged in any way,
for example if the power supply plug or cord is damaged,
liquid has been spilled or objects have fallen into the
equipment, the equipment has been exposed to rain or
moisture, does not operate normally or has been dropped or
damaged.
• Unplug this equipment during lightning storms or when
unused for long periods of time.
• Do NOT defeat the safety purpose of the grounded plug. If
the provided plug does not t into your outlet consult a
qualied electrician to replace the obsolete outlet.
• Do NOT install or use this equipment near water.
• Do NOT expose this apparatus to rain or moisture.
• Do NOT expose to dripping or splashing. No objects lled
with liquid such as vases shall be placed on the equipment.
• Do NOT install near any heat sources such as radiators,
convection heaters or other apparatus such as ampliers that
produce heat.
• Do NOT exceed the maximum load of 10 amps.
Approval Information
The TA-7531US conforms to UL962a, UL1310 and CSA 22.2. The
NEMA outlet is UL listed and conforms to UL 498. The internal PSU
conforms to FCC Part 15b.
PowerHub E Installation Guide
3
PowerHub E Installation Guide
What Is Included In The Box
1 x PowerHub E with Power Cord and Duplex Plug
1 x Black trim
1 x Black Metallic trim
4 x Fixing screws
1 x Installation Guide
4Preparation For Installation
The PowerHub E is designed to be installed in furniture.
Ensure the location chosen for the equipment complies with the
requirements of the “Important Safety Instructions”.
A cutout will need to be made in the furniture, cutout dimensions
are given shown below. After the cutout is prepared the only tools
you will need are a medium sized cross head screwdriver.
The PowerHub E requires power from a standard 3-pin US 120V
outlet.
136mm (max)
5.35in
73mm (max)
(2.87in)
50mm (min)
(1.97in)
65mm (min)
(2.56in)
Front of
furniture
Cutout
Rear of
furniture
PowerHub E Installation Guide
5
PowerHub E Installation Guide
Installation
Before starting installation make sure you have read and
understood the “Important Safety instructions”.
Step 1
Conrm the furniture cutout dimension to accommodate the
PowerHub E is within the limits shown below. Note that in addition
to the minimum depth requirement of 60mm (2.36in) there should
also be at least 50mm (1.97in) clearance below the unit to allow
cabling to exit cleanly.
Step 2
Remove the PowerHub E, trims and screws from the box.
Step 3
Thread the rear power cable through the cutout in the furniture.
Step 4
Lean the PowerHub E on the bottom of the cutout in the furniture
and push it into the cutout by rotating it slightly
Step 5
Fasten the 4 cross head screws to x the PowerHub in the furniture.
Step 6
Align the selected trim (black or metallic) with the PowerHub E
ensuring that the 2 small cutouts on the trim are on the bottom.
Press rmly and evenly to clip the trim into place.
Step 7
Finally insert the plug on the end of the rear power cable into an
appropriate 120V mains outlet.
Installation is now complete.
6
Fitting PowerHub E through the cutout
Additional Information
USB Charging
The PowerHub E provides 2 USB-A sockets for device charging.
The left hand socket charges at 5V/2.4A and the right hand socket
charges at 5V/1A.
Safety Cutout
In the event of an overload the safety cutout may trip. In this case
unplug any devices and wait 5 minutes. The cutout (situated on the
front of the PowerHub) can then be manually reset.
Rotate Push Back
Fix Screws and
Attach Trim
Step 4 Steps 5 and 6
PowerHub E Installation Guide
7
PowerHub E Installation Guide
Removing the PowerHub E from Furniture
If you need to remove the equipment for any reason, rst ensure the
equipment is disconnected from the mains power source.
1. Unplug the PowerHub E from the mains supply.
2. Use a medium at blade screwdriver to release the 2 clips on
the bottom of the trim.
3. The trim can now be gently removed by hand. Be careful not
to bend the trim excessively or it may deform or break.
4. Unscrew the 4 cross head screws and carefully withdraw the
unit from the furniture being careful not to damage any
cables.
Warranty
Please see TeleAdapt “Sales Terms & Conditions” which are
available at http://www.teleadapt.com/teleadapt/sales-terms-
conditions.html
8Contact Details
Americas
TeleAdapt Inc
1315 Greg Street
Suite 110
Sparks
NV 89431
USA
Tel: +1 775 355 8585
Asia
TeleAdapt (Hong Kong) Limited
Hong Kong
Kowloon
Tel: +852 2155 1383
Email: [email protected]
PowerHub E Installation Guide
9
PowerHub E Installation Guide
Visit our website at: www.teleadapt.com
PowerHub E US Installation Guide_06/2023_REV-1.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali TeleAdapt Accessori
