Telecrane F21 Series Manuale utente
F21-2S/2D/4S/4SB/4D/E1/E1B
Table of Contents
Chapter 1 Warranty ------------------------------------------------ 2
Chapter 2 Attention & Precaution ------------------------------- 3
Chapter 3 Installation & Operation ------------------------------ 4
Chapter 4 Software Installation ---------------------------------- 8
Chapter 5 Software Instruction ---------------------------------- 11
Chapter 6 Supplement -------------------------------------------- 25
1
Chapter 1. Warranty
Warranty
Lee’s Hi-Tech Enterprises Co., Ltd. guarantees that this product meets its
published specifications at the time of shipment from the factory. Under
proper installation it should work as expected.
Warranty Period
This equipment is warranted against defects in material and
manufacturing for a period of one year from the date of shipment. During
the warranty period, TELECRANE is responsible for necessary repairs as
long as the product can be proven to be defective.
For warranty service or repair this product must be returned to a service
facility designated by TELECRANE. Buyer will pay shipping charges to
TELECRANE while TELECRANE will pay return shipping charges.
Excluded Items
This warranty does not include consumable parts such as batteries, fuses,
buttons, relays. Also this warranty does not cover defects caused by
improper installation, improper or insufficient maintenance, unauthorized
modification, improper operation, ignorance of environmental
specifications, or improper software or interfacing.
Remarks
◎No other warranty is expressed or implied, except for the above
mentioned.
◎The remedies provided herein are the buyer’s sole and exclusive
remedies. TELECRANE shall not be liable for any direct, indirect,
special, incidental or consequential damages.
2
Chapter 2. Attention & Precaution
Attention
◎Never dismantle the equipment by any unauthorized personnel, or it
may be damaged.
◎After finishing operation of TELECRANE shut off main power to the
crane, power to receiver, and remove transmitter key. If the
transmitter’s power is controlled by a rotary key switch, turn the key to
“OFF” position first, then remove it.
◎The crane should be equipped with main power relay, limit switch and
other safety devices.
Precaution
A. To avoid any interference, the Receiver must be away from motors,
frequency converter and power cable as far as possible.
B. The Receiver should be installed on the top of the electrical control
box. Don’t mount the receiver inside the electrical control box.
C. There are 4.3 billion ID Codes for each complete unit with an
unique one prior to shipment. To avoid any interference, please
manage the remote controls with the different ID Codes at a
working site when installing.
D. It is not allowed to use the same series models with the same
frequency in the range of 200 meters.
Procedures of emergency
In case of an Emergency, please follow the steps below and ask a
distributor for service immediately.
A. Press EMS button.
B. Turn the rotary key switch to the “OFF” position and remove the
magnetic key out of the transmitter.
C. Switch off the main power of crane.
D. Advise the distributor to find out the reason.
3
Chapter 3. Installation & Operation
General Operation
A. Remove the cover of battery box.
B. Install Fresh AA-size batteries in the battery box. Make sure the
“+” and “-” directions are correct.
C. Turn on the power according to the “Power-On Modes”.
Note: LED indicator will flash in red color if proper procedures are
not followed.
D. Operate transmitter by pressing each pushbutton.
E. After operation, perform the following procedures in sequence:
(1) Press EMS mushroom, (2) rotate key counter-clockwise to the
“OFF”position, (3) remove key and keep it in a safe place, (4)
remove batteries if not used for a long period.
Transmitter Batteries
The AA size alkaline batteries are required for the transmitter. DO
NOT use rechargeable batteries. The LED will flash green when the
battery power is sufficient. The LED will flash red when the battery
power is low, and it is required to replace with fresh batteries
immediately.
Receiver Power Supply
There are two type of receiver decoder/relays board for DC and AC
power supply.
A. The voltage range for the DC power supply is DC12 ~ 24V.
B. There are five different transformer with different voltages for the
AC power supply containing AC24/48, 48/110, 48/220, 110/220
and 220/380V, each transformer has two kind of voltage which will
be selected by a Jumper set at HI or LO position on the pc board as
shown on the following Fig.
4
Please find on the following, if the Jumper is set at HI position, the
voltages can be AC48, 110, 220, 220 or 380V; if the Jumper is set at
LO position, the voltage can be AC24, 48, 48, 110 and 220V.
T R A N S F O R M E R
J U M P E R
AC24/
48V
A C4 8 / 1 1 0
V
A C4 8 / 2 2 0
V
AC110/220
V
AC220/380
V
LO
AC24
V
AC48V
AC48V
A C1 1 0 V
A C2 2 0 V
HI
AC48
V
A C1 1 0 V
A C2 2 0 V
A C2 2 0 V
A C3 8 0 V
Changing the Frequency
There are two different PC board for using in two different frequency
range were called VHF and UHF. For each frequency range, by
changing the Crystal of the transmitter and receiver can obtain the
required frequency/channel.
NOTE: Do not replace the crystal for VHF into the UHF PC board
and vice versa. The indication for VHF or UHF is shown
on the PC Board with a check mark “v”.
INSTRUCTIONS:
(1) Pry up the crystal unit with a flat screwdriver.
(2) Remove the crystal unit from the system.
(3) Use a needle nose pliers to straighten both pins of the new crystal
unit.
JUMPER is used as
a voltage selector
(4) Insert the new crystal unit vertically into the PC board.
(5) Press the new crystal down into the socket.
(1) (2)
(3) (4)
5
(5)
The frequencies shown on the same Crystal for the transmitter and
receiver will be different as below:
Replacing the Fuse
Press the fuse cover and turn counter-clockwise with flat screwdriver
to open up the fuse cover, then remove the old fuse. Insert the new
correct fuse into the cover first, place this fuse along with cover into
the fuse holder base, and press the fuse cover and turn clockwise with
flat screwdriver.
T: 321MHz
R: 331.7MHz
If this crystal is used for the transmitter,
then the frequency is 321MHz for the
transmitter.
If this crystal is used for the receiver,
then the frequency is 331.7MHz for the
receiver.
LED Malfunction Alert
A. TX red LED is flashing quickly when any function pushbutton is
pressed, then the problem could be:
(a) One of the pushbutton is jammed.
(b) The EMS mushroom has not been released.
(c) The system is not properly powered on according to the
instructions. If a problem on the above is found, please contact
the distributor for repair.
B. TX LED will flash slowly if the memory of the transmitter is
defective. Please contact the distributor for repair.
C. RX Error LED will flash slowly if the memory of the receiver is
defective. Please contact the distributor for repair.
6
Troubleshooting
A. If TX LED remains with “ON”in red , please remove the batteries
and insert again.
B. If the RX does not respond at all, please turn off the power supply
for 20 seconds and then turn it on again to the receiver.
7
Chapter 4. Software Installation
1-1. The installation function will run automatically after inserting the
software program CD into CD ROM.
Note: If the installation function doesn’t work automatically, please click
“SETUP.EXE”in “My Computer”to complete the software
program installation.
1-1-1. The software installation process is illustrated below:
a. The installation function runs automatically.
b. Click “OK”and continue the installation.
8
c. Click the Computer-like “icon”and continue the installation.
Questo manuale è adatto per i seguenti modelli
7
Indice
Altri manuali Telecrane Controllori
