Teledyne P series Manuale utente
Part Number 203359-01
REV: C
October 2013
© 2013 Teledyne BlueView, Inc. All rights reserved. Printed in USA
All product names are trademarks of their respective companies.
Install ProViewer Software
Insert the CD and run the Setup.
If prompted by a firewall, click “Do not block.”
Configure your PC network interface card
Set your PC Network IP address to 192.168.1.3.
Set the Net Mask to 255.255.255.0.
Bench Test the Sonar
Connect the sonar as shown below.
1) Connect the RJ45 on the Sonar cable to port labeled “Sonar” on POE box.
2) Connect the Ethernet cable to the port labeled “PC” on the POE box and
connect to the computer.
3) Apply AC power to the POE box. The connection will be made in
approximately 60 seconds.
4) Start the ProViewer Software. Click the “Connect” button to connect to sonar.
Quickstart Guide
P-Series Sonar with VDSL
Part Number 203359-01
REV: C
October 2013
© 2013 Teledyne BlueView, Inc. All rights reserved. Printed in USA
All product names are trademarks of their respective companies.
Bench Test the Sonar + VDSL
Connect the sonar as shown below.
1) Connect the RJ45 on the Sonar cable to port labeled “Sonar” on POE box.
2) Connect the RJ11 on the Sonar cable to port labeled “VDSL” or “Line” on the
VDSL box.
3) Connect the Ethernet cable to the port labeled “Ethernet 1” or “LAN 1” on the
VDSL box and connect to the computer.
4) Apply AC power to the POE box and the VDSL box. Connection will be made
in approximately 60 seconds.
5) Start the ProViewer Software. Click the “Connect” button to connect to sonar.
Part Number 203359-01
REV: C
October 2013
© 2013 Teledyne BlueView, Inc. All rights reserved. Printed in USA
All product names are trademarks of their respective companies.
Sonar Cabling
TABLE 1- BURTON INTERCONNECTION TABLE
SIGNAL
CONNECTOR
CONDUCTOR
COLOR
Rx+
1
ORG/WHT
Rx-
2
ORG
Tx+
3
GRN/WHT
12-48V
4
RED (20 AWG)
WHT (20 AWG)
VDSL A
5
BRN
Tx-
6
GRN
GROUND
7
BLK (20 AWG)
GRN (20 AWG)
VDSL B
8
BRN/WHT
TABLE 2- MKS INTERCONNECTION TABLE
SIGNAL
CONNECTOR
CONDUCTOR
COLOR
Rx+
1
ORG/WHT
Rx-
2
ORG
Tx+
3
GRN/WHT
12-48V
4
RED (20 AWG)
12-48V
5
WHT (20 AWG)
Tx-
6
GRN
GROUND
7
BLK (20 AWG)
GROUND
8
GRN (20 AWG)
VDSL A
9
BRN
VDSL B
10
BRN/WHT
For Ethernet, use the Rx+,Rx-,Tx+,Tx- lines.
For VDSL, use the VDSL A and B lines.
Part Number 203359-01
REV: C
October 2013
© 2013 Teledyne BlueView, Inc. All rights reserved. Printed in USA
All product names are trademarks of their respective companies.
Mount the Sonar
The sonar images like a camera out the front of the nose cone. It should be mounted
looking forward, preferably on the same pan-and-tilt as the ROV’s main camera.
Shutdown
To avoid data loss, be sure to close and save any sonar data files before removing
the sonar power.
When power cycling the sonar, be sure to allow at least 10 seconds of ‘off time’
before turning the sonar back on.
Comments
If you have any questions or comments, please contact us.
Teledyne BlueView, Inc.
www.blueview.com
(425) 492-7376
Altri manuali per P series
1
Indice
Altri manuali Teledyne Sonar
Teledyne
Teledyne BlueView M Series Manuale utente
Teledyne
Teledyne UI Manuale utente
Teledyne
Teledyne Sonar UI SeaBat T Series Manuale utente
Teledyne
Teledyne BlueView BV3200 Manuale utente
Teledyne
Teledyne BlueView BV3200 Manuale utente
Teledyne
Teledyne SeaBat T-Series Manuale utente
Teledyne
Teledyne SeaBat T Series Manuale utente
Teledyne
Teledyne P series Manuale utente
