Telematrix 9600IP Manuale utente
1
9600IP VOIP Phone
User Manual
TeleMatrix, Inc
2
1 Introduction…………………………………………………………………………5
1.1 Overview of Hardware…………………………………………………………..5
1.2 Overview of Software……………………………………………………………5
2 Keypad of 9600IP…………………………………………………….……………...6
2.1 Function Table of Keyboard ………………………………………………….....6
2.2 Keyboard function and designed catalog………………………………………...7
3 Set the Phone Through WebBrowser……………………………………………….8
3.1 Login..…………………………………………………………………………....8
3.2 Current state……………………………………………………………………...8
3.3 Network…………………………………………………………………….……..9
3.3.1 Wan Config......................................................................................................9
3.3.2 Lan Config…………………………………………………………………...11
3.4 VoIP……………………………………………………………………………..11
3.4.1 SIP Config…………………………………………………………………...11
3.4.2 Iax2 Config…………………………………………………………………..13
3.5 Advance…………………………………………………………………………14
3.5.1 DHCP Server……………………………………………………………..….14
3.5.2 NAT………………………………………………………………………….15
3.5.3 STUN ………………………………………………………………………..16
3.5.4 Net Service…………………………………………………………………..17
3.5.5 Firewall settings……...………………………………………………………18
3.5.6 VLAN Configuration………………………………………………………..19
3.5.7 Digital Map…………………………………………………………………..19
3.5.8 Call Service Settings………….……………………………………………...21
3.5.9 Memory Key ………………………………………………………………...22
3.5.10 MMI Filter………………………………………………………………….23
3.5.11 Audio Settings……………………….……………………………………..23
3.5.12 VPN………………………………………………………………………...23
3.6 Dial-Peer dial rule setting……………………………………………………….24
3.7 Config Manage………………………………………………………………….25
3.8 Update Firmware…………………………………………………………...…...26
3.8.1 Update……………………………………………………………………….26
3.8.2 Auto Update…………………………………………………………………27
3.9 System Manage…………………………………………………………………28
3.9.1 Account Manage…………………………………………………………….28
3.9.2 Syslog Config………………………………………………………………..28
3.9.3 Phone Book………………………………………………………………….29
3.9.4 Time Set…………………….……………………………………………….29
3.9.5 MMI SET…………………………………………………………………….30
3.9.6 Logout & Reboot…………………………………………………………….30
4 Operating Method for Dialing…………………………………………………….31
4.1 How to dial IP Phone…………………………………………………………...31
4.2Set the Phone to Server……………………………………………………….....,31
3
4.2.1 Set WAN Interface…………………………………………………………31
4.2.2 SIP Setting………………………………………………………………….33
4.2.3 IAX Setting………………………………………………………………...34
4.3How to Use Dialing Rules……………………………………………………….34
4.4 Voice mail……………………………………………………………………….36
Under off-hook status:
Dial “**47”
, the phone broadcasts the IP address
of Wan
Dial “**85”, the phone broadcasts Vlan ID
After the broadcast, please hang-up.
4
Function
1.
Support two SIP server working at the same time
2.Provide a Backup SIP Server
3.
Support NAT, Firewall
4.Support DHCP assign IP address, etc automatically
5.Support PPPoE（used while connecting ADSL，cable modem）
6.It can update the program through HTTP ,FTP and TFTP
7.Check the dynamic voice; Soft the noise; Buffer technique of voice
8.
Hold Function
9.Hotline Function
10.Speed-dial
11.Call-forward
12.Caller ID display
13.DND(Do Not Disturb), Black List, Limit List
14.Auto-answer.
15.Set through standard Web Browser
16.Remote Management Function
17.Classification management for common user’s password and
superuser’s password.
18.Broadcast the IP address and Vlan ID in voice
19.Cordless Handset, 1.9GHz Operation, with Handshake Technology
Standard and Protocols
IEEE 802.3 /802.3 u 10 Base T / 100Base TX
PPPoE
DHCP Client and Server
Support G.711a/u,G729, G7231 5.3/6.3 audio Codec
SIP RFC3261, RFC 2543
Support IAX2
TCP/IP: Internet transfer and control protocol
RTP: Real-time Transport Protocol
RTCP: Real-time Control Protocol
VAD/CNG save bandwidth
Telnet: Internet's remote login protocol
DNS: Domain Name Server
TFTP: Trivial File Transfer Protocol
5
1. Introduction
This is the user manual of 9600IP. Some configuration should be done before
use the 9600IP phone, then it can work normally. This manual will illustrate how to
set the phone through keyboard and web service.
1.1 Overview of Hardware
1.1.1
The two RJ-45 network interface support the 10/100M Ethernet. The default WAN
interface is a DHCP Client server. User connect the WAN interface toADSL or
switch, Lan is web-bridge mode, and bridged the LAN and WAN into the same network..
You can use the administrator’s user name “admin” and password“admin”to login
and set.
1.1.2
Only the WAN interface support the POE.
1.2 Overview of Software
Network Protocol Tone
Ring Tone
Ring Back Tone
Dial Tone
Busy Tone
Phone Function
SIP v1(RFC2543)
V2(RFC3261)
IP/TCP/UDP/RTP/RTCP
IP/ICMP/ARP/RARP/SNTP
TFTP Client/DHCP Client/PPPOE
Client
Telnet/HTTP Server
DNS Clients
Codec
Volume Adjustment
Speed dial key
Phonebook
IP Assignment
G.711：64K bit/s(PCM)
G.723.1：63k/5.3k bit/s
G.726：16k/24k/32k/40k
bit/s(ADPCM)
G.729A：8k bit/s(CS-ACELP)
G.729B：adds VAD & CNG to
G.729
IP (Static IP)
DHCP
PPPoE
Voice Quality Security
HTTP 1.1 basic/digest
authentication for Web setup
MD5 for SIP authentication
(RFC2069/RFC2617)
QoS
VAD：Voice activity detection
CNG：Comfortable noise
generator
LEC：Line echo canceller
Packet Loss Compensation
Adaptive Jitter Buffer QoS field
Call Function NAT Traversal
STUN Call Hold
Call Waiting Configuration
6
Call Forward
Caller ID
3-way conference
Web Browser
Console/Telnet
Keypad
DTMF Firmware Upgrade
DTMF RELAY
DTMF RFC 2833
DTMF SIP Info
SIP Server
TFTP
HTTP
FTP
Support two SIP server working at
the same time
Provide a Backup SIP Server
2 9600IP phone keyboard
2.1 Function Table of Keyboard
2.1.1 Function Table of Base Keyboard
Name Status Function
Store On-hook To enter storage mode for speed dialing
Flash On-hook To enter the deleting mode for pressing down 3
seconds
Redial Dialing Re-dial the last called number
On-hook It’s calling handset for press down for a little time and
registering with handset for pressing down 3 seconds
Locate Call calling the handset
Volume + Call Increase the volume
Volume - Call Decrease the volume
Speak Hands free
Mute Call Mute
On-hook
M1~M10 Dialing 10 speed dial numbers
On-hook
Voicemail Dialing Pick up voicemail
1 Dialing “1”
2 Dialing “2”
3 Dialing “3”
4 Dialing “4”
5 Dialing “5”
6 Dialing “6”
7 Dialing “7”
8 Dialing “8”
9 Dialing “9”
0 Dialing “0”
* Dialing “*”
7
# Dialing It can be regarded as the first number being dialed out
or the end mark for ending number.
2.1.2 Function table of handset keyboard
Name Status Function
ON/OFF Switch for ON and OFF
Hold Call Call waiting
Mute Call Mute
Redial Dialing Re-dial the last called number
Volume + Call Increase the volume
Volume - Call Decrease the volume
Flash Off-hook Hung up the phone and then pick up the phone
Dialing “1”
1 On-hook Holding down of “1” key for messages
2 Dialing “2”
3 Dialing “3”
4 Dialing “4”
5 Dialing “5”
6 Dialing “6”
7 Dialing “7”
8 Dialing “8”
9 Dialing “9”
0 Dialing “0”
Dialing “*”
* Off-hook Press for 3 seconds and into the registration status
# Dialing It can be regarded as the first number being dialed out
or the end mark for ending number.
2.2 Functions of keyboard
2.2.1 Store numbers:
Press “STORE” key to enter into the setting state of storing keys, and input
the storing number, then press the corresponding storing key to store the
numbers.
2.2.2 Call volume control
Press “VOL+” to increase the volume, and “VOL-“ to decrease the volume.
2.2.3 Hold function
It is used for holding the current line or forwarding to other handset, for
example:
When you use the #1 handset and want to use the #2 in a call, now you
need to hold the #1 handset then pick up the #2 handset.
2.2.4 Register handset
Under On-Hook status, pressing the “Locate” key on the base unit for three
seconds to enable the handset register mode, and the Charge indicator light
flashes at the same time; then press the “*”key for three seconds to enable the
8
handset register mode, then the ON/OFF indicator light starts to flash, if then the
base unit and handset have found each other, the Charge indicator light will stop
flashing as well as the ON/OFF indicator light on the handset, and will give the
prompt tone for successful registration.
2.2.5 Delete handset:
Keep pressing the “FLSAH” key on the base unit for three seconds, the
Speaker will give “beep” sound, then
Press “0” on the base unit to delete all the handsets.
Press “1” on the base unit to delete the first handset.
Press “2” on the base unit to delete the second handset.
Press “3” on the base unit to delete the third handset.
Press “4” on the base unit to delete the fourth handset.
Press “5” on the base unit to delete the fifth handset.
After pressed the number keys, Charge indicator light will flashes, which
means the handset is being deleted by the phone. When Charge indicator light
stops flashing, it means that the deletion is finished.
3 Through web browser to set phone
Insert one end of net wire to interface of network card of computer, then insert the
other end to LAN interface of the phone, and set IP of computer 192.168.10.xxx or
automatically get IP. Then open the IE, input 192.168.10.1 on the address field. At this
time you will enter web setting page of phone IP100.
3.1 Login：
The default user name and password are admin/admin and guest/guest.
3.2 Current state
This page layout shows the work state of VoIP phone. The network part shows the
connection state of WAN interface and LAN interface and the network setting; the work
state of Public SIP service of VoIP part, and here you can see the registration and whether
registered to the server or not. The Phone Number part shows the telephone numbers in
Private SIP server and Public SIP server.
9
3.3 Network
3.3.1 Wan Config
WAN port network setting page.
Support static IP, dynamic obtain IP and PPPoE.
Configure Static IP:
----Enable Static;
10
----Set 9600IP’s IP address in the IPAddress;
----Set netmask in the Netmask field;
----Set router IP address in the Gateway;
----DNS Domain:
----Set local DNS server in the Preferred DNS and the Alternate DNS。
Configure to dynamic obtain IP
----Enable DHCP;
If there is DHCP server in your local network, 9600IP will automatically obtain WAN
port network information from your DHCP server.
Configure PPPoE:
----Enable PPPoE
----PPPoE server: Enter “ANY” if no specified from your ITSP.
----Enter PPPoE username and pin in the username and password.
9600IP will automatically obtain WAN port network information from your ITSP if
PPPoE setting and the setup are correct.
Notice: If user accesses the IP phone through WAN port. He/She should use the new
IP address to access the IP phone when the WAN port address was changed.
Indice
Altri manuali Telematrix Telefono IP
Telematrix
Telematrix 3300IP MWB Manuale utente
Telematrix
Telematrix IP550 Manuale utente
Telematrix
Telematrix MARQUIS 9600 Series Manuale utente
Telematrix
Telematrix 3300IP Manuale utente
Telematrix
Telematrix 9700IP Manuale utente
Telematrix
Telematrix 3300IP-TRM Manuale utente
Telematrix
Telematrix NDC2110S Manuale utente
Telematrix
Telematrix 9602IPMWD Manuale utente
Telematrix
Telematrix SIP Phone Manuale di istruzioni
